Banner Q3X Manuel utilisateur

Laser Description and Safety Information

CAUTION: Use of controls or adjustments or performance of procedures

other than those specified herein may result in hazardous radiation

exposure. Do not attempt to disassemble this sensor for repair. A defective

unit must be returned to the manufacturer.

Laser wavelength: 655 nm

Output: < 0.42 mW

Pulse Duration: 5 µs

Installation

Install the Safety Label

The safety label must be installed on Q3X sensors that are used in the

United States.

NOTE: Position the label on the cable in a location that

has minimal chemical exposure.

1. Remove the protective cover from the adhesive on the label.

2. Wrap the label around the Q3X cable, as shown.

3. Press the two halves of the label together.

Figure 3. Safety Label Installation

Sensor Orientation

Correct sensor-to-target orientation is important to ensure proper

sensing. To ensure reliable detection, orient the sensor as shown

in relation to the target to be detected.

For models with background suppression, make sure the intended

target is inside of the contrast sensing range and that any

background objects are positioned beyond the background

suppression distance.

Figure 4. Optimal Orientation of Target to Sensor

Q3X Laser Contrast Sensor

P/N 181486 Rev. E www.bannerengineering.com - Tel: +1-763-544-3164 3

Sensor-to-Background Position

Target Background

X = Diffuse Sensing Range

Y = Recommended

Background

Distance

Model Number X Y

LD50 50 mm (1.97 in) 60 mm (2.36 in)

LD100 100 mm (3.94 in) 120 mm (4.72 in)

LD150 150 mm (5.91 in) 190 mm (7.48 in)

LD200 200 mm (7.87 in) 280 mm (11.02 in)

Figure 5. Q3XBLD Contrast Detection versus Background Suppression

Sensor Mounting

1. If a bracket is needed, mount the sensor onto the bracket.

2. Mount the sensor (or the sensor and the bracket) to the machine or equipment at the desired location. Do not

tighten at this time.

3. Check the sensor alignment.

4. Tighten the screws to secure the sensor (or the sensor and the bracket) in the aligned position.

Wiring Diagram

10-30V dc

Input

Wire

Load

–

NOTE: Open lead wires must be connected to a terminal block.

Key

1 = Brown

2 = White

3 = Blue

4 = Black

5 = Gray

NOTE: The input wire function is user-selectable; see the Instruction Manual for details. The default

for the input wire function is off (disabled).

Cleaning and Maintenance

Handle the sensor with care during installation and operation. Sensor windows soiled by fingerprints, dust, water, oil, etc.

may create stray light that may degrade the peak performance of the sensor. Blow the window clear using filtered,

compressed air, then clean as necessary using 70% isopropyl alcohol and cotton swabs or water and a soft cloth.

Sensor Programming

Program the sensor using the buttons on the sensor or the input wire (limited programming options; see the Instruction

Manual for details).

In addition to programming the sensor, use the input wire to disable the buttons for security, preventing unauthorized or

accidental programming changes. See the Instruction Manual for more information.

Setup Mode

1. Access Setup mode from Run mode by pressing and holding MODE for longer than 2 seconds.

2. Use or to navigate through the top menu.

Q3X Laser Contrast Sensor

4 www.bannerengineering.com - Tel: +1-763-544-3164 P/N 181486 Rev. E

Autres manuels pour Q3X

Table des matières

Autres manuels Banner Accessoires

Banner

Banner Q4X Series Manuel utilisateur

Banner

Banner T30 Manuel utilisateur

Banner

Banner M12 Manuel utilisateur

Banner

Banner R-GAGE Q130RA Series Manuel utilisateur

Banner

Banner L-GAGE LM Series Manuel utilisateur

Banner

Banner Q3XTBLD150-Q8 Manuel utilisateur

Banner

Banner Q4X Series Manuel utilisateur

Banner

Banner L-GAGE LT7 Series Manuel utilisateur

Banner

Banner PresencePLUS P1B65Q Manuel utilisateur

Banner

Banner Q45 Manuel utilisateur

Banner

Banner Sensors T-GAGE M18T Manuel utilisateur

Banner

Banner PresencePLUS Pro Manuel utilisateur

Banner

Banner L-GAGE LE250 IO-Link Manuel utilisateur

Banner

Banner iVu Plus Manuel utilisateur

Banner

Banner Q4X Series Manuel utilisateur

Banner

Banner MSC 1S Series Manuel du propriétaire

Banner

Banner MINI-BEAM Expert Series Manuel utilisateur

Banner

Banner iVu Plus Manuel utilisateur

Banner

Banner L-GAGE LE250 IO-Link Manuel utilisateur

Banner

Banner WORLD-BEAM QS18E Manuel utilisateur

Banner

Banner Q5X Manuel utilisateur

Banner

Banner World-Beam QS30 Manuel utilisateur

Banner

Banner Q4X Series Manuel utilisateur

Banner

Banner Q4X Series Manuel utilisateur

Manuels Accessoires populaires d'autres marques

Hillco

Hillco 2810 Manuel utilisateur

Siemens

Siemens QSA2700D Manuel de l'opérateur

Contours

Contours ZY024 Manuel utilisateur

Saivod

Saivod VS621 Manuel utilisateur

Virtuox

Virtuox VirtuCLEAN 2.0 Manuel utilisateur

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS Manuel utilisateur

Z-Wave

Z-Wave HSD-200Z Manuel utilisateur

turck

turck FMX-IM-2UPLI63FX Manuel utilisateur

Decagon Devices

Decagon Devices 10HS Manuel utilisateur

UPPAbaby

UPPAbaby Cup Holder Manuel utilisateur

Elko

Elko SmartSensor Leakage Wireless Manuel utilisateur

Grizzly

Grizzly H8371 Manuel utilisateur

Panasonic

Panasonic HG-T Series Manuel utilisateur

IFM Electronic

IFM Electronic Efector 250 Series Guide de référence

DigiDesign

DigiDesign 888/24 I/O Manuel utilisateur

PROZIS

PROZIS QUAY Manuel utilisateur

patagonia

patagonia PSI Vest Manuel utilisateur

SFC Energy

SFC Energy EFOY GO! Manuel utilisateur