Balanced Audio Technology REX II Manuel utilisateur

REX II Power

WARRANTY REGISTRATION FORM

Unit Serial Number:

_______________________________________

Customer Name:

_______________________________________

Address:

_______________________________________

Date of Purchase:

_______________________________________

Purchased From:

Dealer Name:

_______________________________________

Address:

_______________________________________

IMPORTANT NOTE:

In order to receive the full five year product warranty, please

mail this completed form together with a copy of your sales

receipt to Balanced Audio Technology at the address below,

within thirty days of purchase.

Failure to do so will result in the product being warrantied for

one year from the date of manufacture.

1300 First State Blvd. Wilmington DE 19804 Tel: 302-999-8855 Fax: 302-

999-8818

REX II Power

Special Edition

Balanced Power Amplifier

Owner's Manual

1300 First State Blvd. Wilmington DE 19804 Tel: 302-999-8855 Fax: 302-

999-8818

Introduction

Thank you for your purchase of the Balanced Audio Technology REX II

Power vacuum tube amplifier. Please read this owner’s manual to obtain

the full benefit of the REX II Power in your system. This manual provides

you with necessary safety information and operating procedures for this

exceptional unit.

WARNINGS:

To prevent the possibility of serious injury, electrical shock, or fire:

DO NOT operate with the bottom cover removed.

DO NOT expose to rain or moisture.

DO NOT defeat the ground Power-plug.

DO NOT replace fuses with anything other than the same type and rating

as supplied by the factory.

Package Contents

Included in the box should be the following:

Description Quantity

REX II Power Amplifier 1

6C33C-B Output Tubes 4

6SN7 Signal Tubes 6

6H30 Super Tubes 4

6V6 Power Tubes 2

Power Cord 1

Torx Wrench (T-10) 1

Spare Cover Screws 5

Spare Fuses 2

Owner’s Manual 1

Optional Accessories (as ordered)

Save all the packaging materials in a safe dry area for the unlikely event

that you need to return the REX II Power to the factory for service.

Installing Tubes

1. Install 6SN7 tubes in positions V1 through V6

2. Install 6H30 SuperTubes in positions V7, V8, V15 and V16

3. Install 6C33 tubes in positions V9 through V12

4. Install 6V6GT tubes in positions V13 and V14

NOTE: Care must be exercised when installing the 6C33 output tubes.

While inserting the tubes, please use gentle circular motion in order to

facilitate proper socket pin engagement. Do not use force, as doing this

might damage the socket pins and/or tubes.

Physical Placement

It is recommended that you provide open space above the unit for proper

ventilation, with no electronic components or shelves placed directly

overhead.

Mount the unit on a hard surface with proper ventilation underneath.

Avoid placing the unit directly on a carpeted floor, as doing so will block

the ventilation slots in the unit’s bottom cover.

Connecting the REX II Power to Your System

For Balanced Preamplifiers:

Use balanced XLR interconnects. The left and right channel input

connectors are clearly marked on the back panel of the REX II Power.

Note: The REX II Power XLR inputs are wired as follows:

Pin 1: common/shield

Pin 2: positive

Pin 3: negative

For Single-Ended Preamplifiers:

Single-ended preamplifiers have RCA connectors. The REX II Power power

amplifier is designed to work with either balanced or single-ended

preamplifiers connected to its inputs. All that is required to connect a

single-ended preamplifier with RCA connectors to the REX II Power’s

inputs is the optional balanced to single-ended adapters. These adapters are

available from Balanced Audio Technology.

For Speaker Connections:

The speaker connectors are clearly marked on the back panel of the REX II

Power amplifier. There are three sets of output taps marked LOW,

MEDIUM and HIGH for connecting a variety of speakers to the REX II Power

output. Please note that some experimentation may be required. Try

each output tap until you find the one that gives the most balanced

performance in your system.

Operating the REX II Power

Normal operation of the REX II Power amplifier requires simply turning the

unit on. There are no meters to connect, bias setpoints to remember, or

drifting bias points to adjust. Please read the Autobias Feature section

for more details.

Turning the REX II Power ON:

The main power switch is located at the rear of the unit. When you turn

the unit on, it will go through a gentle power-on sequence. After about

one minute, four LED’s visible from the top of the chassis should light up.

This indicates that full operating bias has been reached and the unit is

now ready to play.

Turning the REX II Power OFF:

The unit can be turned Off at any time (even while playing). If needed,

please wait at least 30 seconds before turning the unit ON again.

Autobias Feature:

The REX II Power implements a sophisticated autobias circuit that

automatically compensates for tube aging and line voltage fluctuations,

as well as marginal mismatching of tubes. The successful operation of

the autobias circuit is noted by individual LED’s that glow visibly next to

each output tube when viewed from the top of the chassis. A total of

four LED’s should light up to indicate proper operation of the circuit. If

one of the LED’s fails to light up (after the unit is warm), there could be

two reasons for this problem:

1. The particular output tube is defective. In this case replacing

this tube with a known good one should turn the LED ON again.

2. The amplifier was overstressed and its thermal protection was

activated. Simply turning it OFF and then ON again will clear that

protection.

NOTE: For more details on the operation of the REX II Power protection

circuit please see the correcponding chapter.

Protection Circuits

Your REX II Power amplifier is equipped with two types of sophisticated

protection circuits.

Thermal Protection. Thermal protection circuits monitor power

dissipation in each of the unit’s four output tubes. Should the power

dissipation in that part of the circuit exceed the preset value, the

protection mechanism will disable that particular tube. The corresponding

green LED will then go out.

When this happens, simply turn the unit OFF using the rear panel power

switch, then turn it back ON after waiting a couple of minutes. That

should clear the thermal protection mechanism.

Overcurrent Protection.There are four independent over-

current protection circuits monitoring the currents flowing through each

output tube. Should the current excee the preset value, the protection

circuit will disable that particular tube, and the green LED will go OFF.

To clear the fault one should simply power cycle the unit OFF and then

back ON.

Understading the Overcurrent Protection.

The REX II Power can enter over-current protection mode if either of the

following conditions take place:

1. The unit is being driven hard into a speaker that represents a

particularly difficult load. At a point of peak demand the over-

current protection may become activated. Power cycling the unit

will restore its operation.

2. An over-current protection due to an intermittent internal

discharge in one of the power tubes.

The internal discharge can take several forms. In some instances the

weak spot in the tube will evaporate, and the tube will continue working

normally for an extended period of time.

In other cases the tube might continue activating the protection circuit,

indicating the need for replacement.

The standard recommendation is to ignore the first occurance, and

replace the tube following any further events.

What to do when the LED light goes out:

If you notice that one or more green LED’s goes out, the first step should

be to RECORD THEIR POSITIONS.

Then turn the unit OFF by using its main power switch, wait a couple of

minutes and turn it back ON.

If the same tubes exhibit the same fault again, they should be replaced.

While it is always best to replace a matched pair of tubes, it is not always

absolutely required. If your unit is farily new, then you might consider

replacing just one faulty tube. The factory can supply a tube with similar

characteristics.

Replacing the Fuse:

WARNING: Please turn the unit OFF and disconnect the power

cord before proceeding.

There are NO internal fuses in the REX II Power amplifier.

The main power fuse is Slow-Blow type, located on the amplifier’s back

panel, and should only be replaced with the same type and rating fuse:

100-120V 10A

200-240V 7A

If the unit still fails to operate properly, please contact the factory for

professional service.

Factory supplied fuse should only be replaced with the same

type and rating part.

Autres manuels pour REX II

Table des matières

Autres manuels Balanced Audio Technology Amplificateur

Balanced Audio Technology

Balanced Audio Technology VK-75 Manuel utilisateur

Balanced Audio Technology

Balanced Audio Technology VK-52SE Manuel utilisateur

Balanced Audio Technology

Balanced Audio Technology VK-250 Manuel utilisateur

Balanced Audio Technology

Balanced Audio Technology VK-300x Special Edition Manuel utilisateur

Balanced Audio Technology

Balanced Audio Technology VK-5SE Manuel utilisateur

Balanced Audio Technology

Balanced Audio Technology VK-1000 Manuel utilisateur

Balanced Audio Technology

Balanced Audio Technology VK-30SE Manuel utilisateur

Balanced Audio Technology

Balanced Audio Technology VK-60 Manuel utilisateur

Balanced Audio Technology

Balanced Audio Technology VK-P3 Manuel utilisateur

Balanced Audio Technology

Balanced Audio Technology VK-P5 Manuel utilisateur

Balanced Audio Technology

Balanced Audio Technology VK-500 Manuel utilisateur

Balanced Audio Technology

Balanced Audio Technology VK-42SE Manuel utilisateur

Balanced Audio Technology

Balanced Audio Technology VK-60SE Manuel utilisateur

Balanced Audio Technology

Balanced Audio Technology VK-3iX Manuel utilisateur

Balanced Audio Technology

Balanced Audio Technology VK-50 Manuel utilisateur

Balanced Audio Technology

Balanced Audio Technology VK-55 Manuel utilisateur

Balanced Audio Technology

Balanced Audio Technology VK-33SE Manuel utilisateur

Balanced Audio Technology

Balanced Audio Technology VK-5i Manuel utilisateur

Balanced Audio Technology

Balanced Audio Technology VK-75SE Manuel utilisateur

Balanced Audio Technology

Balanced Audio Technology REX II Manuel utilisateur

Balanced Audio Technology

Balanced Audio Technology VK-31SE Manuel utilisateur

Balanced Audio Technology

Balanced Audio Technology VK-250M Manuel utilisateur

Balanced Audio Technology

Balanced Audio Technology VK-600M Manuel utilisateur

Balanced Audio Technology

Balanced Audio Technology VK-31 Manuel utilisateur

Manuels Amplificateur populaires d'autres marques

ASTRO

ASTRO HVO V40 P Manuel utilisateur

Marantz

Marantz SUPERSCOPE BLA-545 Instructions de montage

NAD

NAD CI980 Manuel utilisateur

Technics

Technics SE-CH770 Manuel utilisateur

Harman Kardon

Harman Kardon HK6300 Manuel utilisateur

NAD

NAD T975 Manuel utilisateur

McIntosh

McIntosh MA6850 Manuel utilisateur

Electro-Harmonix

Electro-Harmonix ENGLISH MUFF’N Manuel utilisateur

Viatron

Viatron Autrix Manuel utilisateur

GME

GME GA9800 Manuel utilisateur

Atlas

Atlas CP700 Manuel utilisateur

Roland

Roland KC-1000 Manuel utilisateur

Pyle

Pyle PFMRA350BW Manuel utilisateur

Advantage

Advantage S-250 Manuel utilisateur

IRT Electronics

IRT Electronics DVA-3007 Manuel utilisateur

Dimavery

Dimavery BA-100 Series Manuel utilisateur

Sony

Sony XM-S400D Manuel utilisateur

Schertler

Schertler ROY X Manuel utilisateur