Baja Designs 45-7500 Manuel utilisateur

Jeep JK S8/Onx6 Mount Kit

PN: 45-7500, 45-7503

Installation Manual

Baja Designs • 185 Bosstick Blvd. • San Marcos • CA • 92069

Phone 760.560.2252 • Fax 760.560.0383 • info@bajadesigns.com

www.bajadesigns.com

Bracket Installation:

1. Start by remove the factory A-Pillar

bolts on the left and right side of

your Jeep.

2. Next you will want to install the

Baja Designs Jeep JK Mounting

Brackets. These brackets are

designed to use the factory bolts.

3. Once the brackets have been

installed you can mount the S8 or

OnX6 with the power cord located

on the driver’s side of the vehicle. NOTE: For the OnX6 you will use the ½” spacers and

¼-20x1.125 provided in the kit. (See Below)

4. Remove the factory bolts securing the trim between the hood and windshield and route the

power cord as shown in the four photos below.

function of the light. When the momentary button is pushed the light will toggle between medium and

high. When the momentary button is held for two seconds the light will go into strobe mode. To get

out of the strobe mode just push the button and the light will go back to full power.

If you decide to use the switches provided with this kit you will need to find a place in the dash area

to drill two 15/32” holes for mounting purposes. Be certain there is adequate clearance for the body

of the switch behind the mounting location

before drilling. If you choose to run our optional mode switch you will need to drill a 5/8” into the

desired area. Note: Installation of the mode switch is optional so if you do not want to

The wiring harness includes our

toggle switch w/led and momentary button for the “mode”

have a medium and strobe mode you will need to isolate the green and black wires from

each other.

For the installation shown in these photos the customer provided us with a very clean switch panel

made by Daystar.

(http://www.daystarweb.com/productlisting.php?make=Jeep&prodcat=Dash+Panels)

The Daystar panels are designed to accept the Carlisle style switches that most retailer automotive

stores sell.

1. Start by routing our wiring harness with the fuse block side along the firewall as shown in the

two pictures below.

2. Follow the factory wiring harness along the inner fender on the driver’s side and mount the

relay to the factory ground location by removing the 10mm nut located in the engine bay.

3. Once you have mounted the relay route the 3 pin connector along the factor harness and plug

it into the power cord from the light.

There is a bypass that allows you to get the switch wires inside the cab. This can be done by

removing the plastic cover on the end of the dash which is located on the driver’s side.

4. Take a wire coat hanger and push through the foam from the cab side to the outside. Use

electrical tape and secure the harness to the coat hanger then pull the harness through the

foam with the coat hanger like the photos shown below.

5. Once you have the harness inside the cab route the wires under the dash to the area where

you are mounting the switches. Note: Use zip-ty’s to secure the harness.

6. The BLACK wire goes to the terminal labeled “GROUND” on the switch. The BLUE wire goes

to “ACC.” The BROWN wire goes to “POWER.” On the mode switch, polarity is unimportant

for the green and black wires.

7. You will notice a ring terminal on the other end of the black wire that is shared by the

momentary and the toggle switch. This needs to be attached to a metal mounting bolt under

the dash. Make sure the bolt is chassis grounded. This ground is for the LED light in the

toggle switch as well as the ground for the mode function of the momentary button.

8. Before you finish the installation turn your S8 or OnX on to verify the system is working

properly. Once you are satisfied with your work use the provided zipty’s to secure the

harness.

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Baja Designs Accessoires automobiles

Baja Designs

Baja Designs S2 Pro Manuel utilisateur

Baja Designs

Baja Designs Squadron Manuel utilisateur

Baja Designs

Baja Designs S1 Mode d’emploi

Baja Designs

Baja Designs 447575 Manuel utilisateur

Baja Designs

Baja Designs 44-7534 Manuel utilisateur

Baja Designs

Baja Designs S8 Manuel utilisateur

Baja Designs

Baja Designs 448024 Manuel utilisateur

Baja Designs

Baja Designs 44-7807 Manuel utilisateur

Manuels Accessoires automobiles populaires d'autres marques

James Baroud

James Baroud Odyssey Manuel utilisateur

Motorola

Motorola i50sx Manuel utilisateur

Yakima

Yakima 9MM STANDARD BIKE MOUNT Manuel utilisateur

Feniex

Feniex T3 Manuel utilisateur

Renault

Renault 77 11 423 180 Manuel utilisateur

Kia

Kia E8300-4D000 Manuel utilisateur

Brink

Brink 756843 Manuel utilisateur

Whispbar

Whispbar K085W Manuel utilisateur

v.link

v.link CI-VL2-PC-HSD Manuel utilisateur

Viking

Viking Stack-Rack Guide de configuration rapide

Aries

Aries 203015 Manuel utilisateur

Choetech

Choetech AT0005 Manuel utilisateur

ZZ2

ZZ2 ZZAIR-PRO Manuel utilisateur

Holman

Holman 4A80L Manuel utilisateur

Thule

Thule 2075 Manuel utilisateur

Motorola

Motorola T325 Manuel utilisateur

TAUBENREUTHER

TAUBENREUTHER 16-3950 Guide d'installation

DV8

DV8 FBJL-02 Manuel utilisateur