Bafo BF-460 Manuel utilisateur

USER’S MANUAL

USB 2.0 PCI Card

BF-460

USB 2.0 PCI Card User’s Manual 1

1. Introduction

BF-460 is a PCI card fully functional of USB 2.0 Host, which supports High-Speed,

Full-Speed, & Low-Speed operation and follows the Enhanced Host Controller

Interface (EHCI) specification.

2. Package Content

Hardware: USB 2.0 PCI Card

Software: Driver software in CD-ROM

User’s Manual

3. Product Features

USB specification revision 2.0 compliant

Data transfer rate up to 480Mbps

Support up to 127 USB devices

Fully compatible with USB 1.1 devices

OHCI specification for USB 1.1 compliant

Five downstream ports (4 external ports and one internal port) support High-

speed (480Mbps), Full-speed (12Mbps) or Low-speed (1.5Mbps)

32-bit 33MHz host interface, PCI specification revision 2.2 compliant

PCI-Bus power management interface specification revision 2.1 compliant

Support hot swap and wake-up

4. System Requirements

IBM PC Pentium II 266MHz CPU or higher or compatible system

Available PCI slot

CD-ROM drive

Windows® 98/98SE, Windows®ME, Windows®2000, Windows®XP

USB 2.0 PCI Card User’s Manual 2

5. Hardware Installation

5.1Turn off your computer, unplug the power cord, disconnect all peripheral devices

and remove the PC case.

5.2Locate the PCI slots on the motherboard; remove any add-on card, which blocks

easy access to the PCI slots.

5.3Take the USB 2.0 PCI card out of its anti-static bag and push it into the first empty

PCI slot.

Note: There is only one way that your USB 2.0 PCI card can fit the slot correctly.

5.4Re-install any add-on card that removed, re-connect all peripheral devices,

assembly the PC case and plug the power cord.

USB 2.0 PCI Card User’s Manual 3

6. Software Installation (Windows®98, ME as example)

6.1Windows®98 Driver Installation

6.1.1 Power on the computer, Windows®will detect an unknown device and

run the “Add New Hardware Wizard” to assist you in setting up the

new device.

6.1.2 Insert the driver of USB 2.0 PCI card into CD-ROM drive, click

“Next” to continue.

6.1.3 Select “Search for the best driver for your device” and click

“Next”

6.1.4 When the Windows®appears as below, click “NEXT” to continue.

USB 2.0 PCI Card User’s Manual 4

6.1.5 Select the updated driver (Recommended), and then click “NEXT”

to continue.

6.1.6 Windows® will detect the suitable driver; click “NEXT” to continue.

6.1.7 Windows® will install the driver to your system.

USB 2.0 PCI Card User’s Manual 5

6.1.8 When the Windows®appears as step 6.1, repeat the steps 6.1.1 to

6.1.7.

6.1.9 When the Windows®appears as below, click “NEXT” to continue.

6.1.10Select “Search for the best driver for your device” and click

“Next”

USB 2.0 PCI Card User’s Manual 6

6.1.11Select Specify a Location and browse the driver’s location

“D:\Win98ME” in the dialog (D: represents the CD-ROM Drive),

then click “NEXT” to continue.

6.1.12 When the Windows®appears as below, click “NEXT” to continue.

6.1.13 After installation is complete, you have to check “My Computer”-

“Control Panel”-“ System”-“Device Manager” and you can see a

“NEC PCI to USB Enhanced Controller”, “NEC USB Open Host

Controller” under the Universal Serial Bus Controller.

USB 2.0 PCI Card User’s Manual 7

6.2 Windows®2000 Driver Installation

6.2.1 Power on the computer, Windows®will detect an unknown device and

run the “Add New Hardware Wizard” to assist you in setting up the

new device.

6.2.2 Insert the driver of USB 2.0 PCI card into CD-ROM drive, click

“Next” to continue.

6.2.3 Select Search for a suitable driver for my device (recommended),

and then click “NEXT”.

6.2.4 Select Specify a location and click “NEXT”.

USB 2.0 PCI Card User’s Manual 8

6.2.5 Browse the driver’s location ”d:\win2kxp\nehcd.inf” in the dialog (D:

represents the CD-ROM Drive), and then click “OK”

6.2.6 Click “NEXT” to continue.

6.2.7 Windows®will install the driver to your system.

6.2.8 Click “Finish” to complete the setup procedure.

USB 2.0 PCI Card User’s Manual 9

6.2.9 After install the driver, you have to check the “Control Panel”-

“System”-“Hardware”-“Device manager” to make sure that the

driver has already installed properly. In the Universal Serial Bus

controller you can see the NEC PCI to USB Enhanced Controller

and NEC PCI to USB Host Controller

Table des matières

Autres manuels Bafo Carte PCI

Bafo

Bafo BF-462 Manuel utilisateur

Manuels Carte PCI populaires d'autres marques

ERMA

ERMA SSI 1417 Manuel utilisateur

SIIG

SIIG CyberSerial Dual PCI Instructions de montage

Moxa Technologies

Moxa Technologies CP-102E Manuel utilisateur

I-Bus

I-Bus IBC2602 Manuel utilisateur

Exsys

Exsys EX-60102 Manuel utilisateur

Chelsio Communications

Chelsio Communications T5 Series Manuel utilisateur

Conrad Electronic

Conrad Electronic 97 46 71 Manuel utilisateur

Micro Innovations

Micro Innovations USB650A Manuel utilisateur

KTI Networks

KTI Networks KF-310 Manuel utilisateur

Asus

Asus SpaceLink WL230 Manuel utilisateur

SIIG

SIIG SC2475 Manuel utilisateur

TRENDnet

TRENDnet TEW-703PI Manuel utilisateur

Belkin

Belkin F5D7000F Manuel utilisateur

Pericom

Pericom PI7C7100 Manuel utilisateur

ADLINK Technology

ADLINK Technology cPCI-3548 Manuel utilisateur

Digium

Digium TE200 Series Manuel utilisateur

Allo.com

Allo.com 2nd Gen E1/T1/J1 Manuel utilisateur

Western Digital

Western Digital FireWire PCI Adapter Manuel utilisateur