Bacharach Flue-Gas Sample Conditioning System Manuel utilisateur
Introduction
The Bacharach Flue-Gas Sample Conditioning System consists of the
following components:
• Probe with Peltier Cooler
• Condensate Pump with Water Trap
• Power Supply
The function of this system is to remove water vapor from the flue-gas
sample, thus preventing the formation of water droplets inside the
probe hose. If water droplets were to form inside the hose, a portion of
the gas sample could be absorbed by the water, thus resulting in lower-
than-actual readings of NO2and SO2.
Water vapor is removed from the flue-gas sample by passing the sample
through a Peltier Cooler where the sample is chilled, which in turn,
causes the water vapor contained in the gas sample to be removed from
the sample.
The water that was extracted from the gas sample is then pumped out
of the Peltier Cooler and into a water trap.
The now dry, conditioned flue-gas sample is then sent to its associated
combustion test equipment for analysis.
Product Leadership • Training • Service • Reliability
Figure 1. Flue-Gas Sample Conditioning System
Probe w/ Peltier Cooler
Power Supply
Instruction 0024-9415
Flue-Gas Sample
Conditioning System
P/N 0024-7224
Rev. 8 – May 2010
Pump
w/ Water Trap
Instruction 0024-9415 Bacharach, Inc. 3
Flue Gas Sample Conditioning System
Technical Data
Probe:
Standard Length......................................................... 11.5 in (295 mm)
Optional Lengths ............................................................. 7 in (180 mm)
19.5 in (500 mm)
39 in (1000 mm)
Peltier Cooler:
Inlet Sample Dew Point.......................................... 149 °F (65 °C) max.
Outlet Sample Dew Point.................18 °F (10 °C) min. below ambient
Cooling Power ................................................................................. 10 W
Environment Temperature ............................. 32 to 104 °F (0 to 40 °C)
Weight ................................................................................8.5 oz (240 g)
Condensate Pump:
Sample Flow Rate..........................................................1.5 LPM @ STP
Length of Hose ...................................................................... 6.6 ft (2 m)
Reservoir Storage........................................................................... 50 ml
Environment Temperature ............................. 32 to 104 °F (0 to 40 °C)
Weight ..............................................................................12.7 oz (360 g)
Power Supply:
Input ..............................................................100 to 240 VAC, 50/60 Hz
Output ............................................................ 9 VDC, max. @ 4 A, max.
Equipment Setup
Refer to Figure 2. If not already done, attach the Peltier cooler to the
probe assembly by first removing the plastic end cap from the rear of
the probe, and then inserting the cooler’s inlet connector, ensuring first
that a filter is present between the cooler and probe.
Attach the pump’s inlet hose to the bottom of the Peltier cooler. Water
that is condensed from the flue-gas sample will be pumped into the con-
densate pump’s reservoir through this hose. Note that the condensate
pump can be placed in an upright, horizontal, or hanging position. A
magnet mounted in the base of the pump allows the pump to be at-
tached to overhead ductwork.
Connect the power supply’s DC output connector to the condensate
pump; then connect the condensate pump’s DC output power connector
to the Peltier cooler. The Peltier cooler and its associated condensate
pump are started by plugging the power supply into a source of AC
power that is between 100 and 240 VAC, 50/60 Hz.
Connect the probe assembly’s stack-temperature thermocouple con-
nector, pressure fitting, and flue-gas fitting to the combustion analyzer
per the analyzer’s instruction manual.
Flue Gas Sample Conditioning System
4Bacharach, Inc. Instruction 0024-9415
Figure 2. Equipment Setup
PELTIER
COOLER
PROBE ASSEMBLY
PUMP
POWER SUPPLY 100 – 240 VAC
50/60 HZ
Connect to
Combustion Test
Equipment
STACK TEMP.
THERMOCOUPLE
PRESSURE (Blue)
FLUE GAS (Yellow)
Instruction 0024-9415 Bacharach, Inc. 5
Flue Gas Sample Conditioning System
Operation
When ready to conduct a combustion efficiency test, plug in the power
supply of the Flue-Gas Sample Conditioning System. You should hear
the condensate pump start running and see the Peltier cooler’s red LED
turn on and off as the cooler is cycled. Note that the cooler’s operating
time changes according to its temperature.
Set up and configure the combustion analyzer as described in its in-
struction manual. Then insert the probe into the flue stack and begin
testing.
During the combustion test, the condensed water vapor from the flue
gas will accumulate inside the pump’s reservoir. If the water level be-
gins to approach the ends of the tubes inside the reservoir, then stop the
test and empty the reservoir as described in the Maintenance Section of
this manual.
WARNING! The probe tube is hot! In the following step, be
sure to allow the probe tube sufficient time to cool before
handling.
At the conclusion of the combustion test, remove the probe from the
stack; then unplug the Peltier cooler’s power supply.
Flue Gas Sample Conditioning System
6Bacharach, Inc. Instruction 0024-9415
Maintenance
Probe
The probe’s sponge-type filter (Figure 3, Item 9) needs to be inspected at
regular intervals for dirt contamination. Replace filter as necessary by
first pulling out the Peltier cooler from the probe and then exchanging
the filter with a new one.
Peltier Cooler
The cooler’s wadding filter (Figure 3, Item 12) needs to be inspected at
regular intervals for dirt contamination. Replace filter as necessary by
first pulling off the filter chamber’s top cap and then exchanging the
filter with a new one.
Condensate Pump
WARNING! The condensed water will be warm and slightly
acidic. Take all necessary precautions to prevent the water
from splashing into your eyes or contacting your skin.
Empty the pump’s reservoir (Figure 3, Item 15) by first holding the
pump with its reservoir facing downwards. Then twist the reservoir 90
degrees (either clockwise or counterclockwise) to free it from the pump
base. Empty the reservoir; then reattach it to the pump. Before reat-
taching the reservoir, however, make sure that the reservoir’s o-ring
(Figure 3, Item 20) is properly positioned inside its grove in the pump
base.
The pump’s wadding filter (Figure 3, Item 17) needs to be inspected at
regular intervals for dirt contamination. Replace filter as necessary by
first unscrewing the filter chamber cap and then exchanging the filter
with a new one.
Instruction 0024-9415 Bacharach, Inc. 7
Flue Gas Sample Conditioning System
Replacement Parts
Item Description Part No.
(Fig 3)
Probe:
1 Complete Assembly (w/ 11.5 in. probe tube)............. 0024-3038
2 Probe Tubes:
7 in. (180 mm) ...................................................... 0024-1183
11.5 in. (295 mm) ................................................. 0024-1184
19.5 in. (500 mm) ................................................. 0024-1185
39 in. (1000 mm) .................................................. 0024-1186
3 Gas Hose Fitting ........................................................ 0024-0877
4 Draft Hose Fitting...................................................... 0024-0878
5 Probe Stop .................................................................. 0019-3037
6 Thumb Screw ............................................................. 0102-0875
7 Screw, M4 x 6mm....................................................... 0501-3829
8 Retaining Nut............................................................. 0102-3740
9 Filter (Qty. 5).............................................................. 0007-1646
Peltier Cooler & Power Supply:
10 Complete Assembly, Peltier Cooler & Power
Supply (AC Power Cord not included) ................... 0024-1179
11 Plastic End Cap.......................................................... 0106-5454
12 Filter Wadding ........................................................... 0007-1647
13 Power Supply ............................................................. 0304-1713
14 AC Power Supply Cord, 3-Wire................................. 4998-8986
Condensate Pump:
15 Complete Assembly.................................................... 0024-1180
16 Reservoir .................................................................... 0106-5453
17 Plastic Screw-On Cap ................................................ 0106-5455
18 Filter Wadding (Qty. 1).............................................. 0024-1205
19 Plastic Cap w/ Drain .................................................. 0106-5456
O-Rings:
20 9 x 2 mm ..................................................................... 0105-5105
21 4 x 1.75 mm ................................................................ 0105-5106
22 50 x 3 mm ................................................................... 0105-5107
23 11 x 1 mm ................................................................... 0105-5108
Flue Gas Sample Conditioning System
8Bacharach, Inc. Instruction 0024-9415
Figure 3. Replacement Parts
11
20
20
12
Part of Item 10
1
21 96
7852
Part of Item 10
13 14
18
23
17
22
16
20 19
15
Instruction 0024-9415 Bacharach, Inc. 9
Flue Gas Sample Conditioning System
Bacharach Sales/Service Centers
Service can be obtained by contacting a Bacharach Service
Center at the following locations:
United States
Bacharach, Inc.
621 Hunt Valley Circle
New Kensington, PA 15068
Phone: 724-334-5051
Fax: 724-334-5723
Email: help@mybacharach.com
Canada
Bacharach of Canada, Inc.
20 Amber St. Unit #7
Markham, Ontario L3R SP4
Canada
Phone: 905-470-8985
Fax: 905-470-8963
Email: bachcan@idirect.com
Flue Gas Sample Conditioning System
10 Bacharach, Inc. Instruction 0024-9415
Instruction 0024-9415 Bacharach, Inc. 11
Flue Gas Sample Conditioning System
Headquarters:
621 Hunt Valley Circle, New Kensington, PA 15068
Ph: 724-334-5000 • Fax: 724-334-5001 • Toll Free: 800-736-4666
Ce manuel convient aux modèles suivants
1
Table des matières
Autres manuels Bacharach Équipement de test
Bacharach
Bacharach Leakator 10 Manuel utilisateur
Bacharach
Bacharach TRUE-SPOT Fiche technique
Bacharach
Bacharach Fyrite INSIGHT Manuel d'installation et d'exploitation
Bacharach
Bacharach GDC-150 Manuel utilisateur
Bacharach
Bacharach DIOXOR 19-7038 Manuel utilisateur
Bacharach
Bacharach High Performance Oilless Commercial Refrigerant Recovery... Manuel utilisateur
Bacharach
Bacharach ECO-2020 Manuel utilisateur
Bacharach
Bacharach Fyrite Tech 50 Manuel utilisateur
Bacharach
Bacharach 2810 Manuel utilisateur
Bacharach
Bacharach Model 105 Manuel utilisateur
Bacharach
Bacharach Tru Pointe Ultra Mode d’emploi
Bacharach
Bacharach Fyrite Tech 50 Manuel
Bacharach
Bacharach DIOXOR II Manuel utilisateur
Bacharach
Bacharach R-22id Mode d’emploi
Bacharach
Bacharach PUR-CHEK Mode d’emploi
Bacharach
Bacharach ODOROMETER Manuel utilisateur
Bacharach
Bacharach Fyrite INSIGHT Manuel utilisateur
Bacharach
Bacharach ECA 450 Manuel utilisateur
Bacharach
Bacharach Fyrite INSIGHT Instructions d'installation et d'utilisation
Bacharach
Bacharach Monoxor III Manuel d'installation et d'exploitation
Manuels Équipement de test populaires d'autres marques
SMART
SMART KANAAD SBT XTREME 3G Series Manuel utilisateur
Agilent Technologies
Agilent Technologies BERT Serial Manuel utilisateur
Agilent Technologies
Agilent Technologies N3280A Manuel utilisateur
Vernier
Vernier Go Direct Voltage Manuel utilisateur
Lifeloc
Lifeloc R.A.D.A.R. Manuel utilisateur
Fluke
Fluke T5-600 Instructions d'utilisation et d'installation
