B2 Audio RIOT 3200 Manuel utilisateur

riot 3200/7500

product id: riot3200fr21 / riot7500fr21

riot

Go all the way across. Fullbridges have come to stay. The RIOT 3200 & The RIOT 7500 has now had it’s rst revision, oering even better features than

previously. The V2 has gotten better crossovers, an increased operational voltage, so your LTO battery system can be charged correctly. In addition the

clip protection has been revised for better operation. To top it all o, is the new bass remote with the built in voltmeter.

B2 audio has downsized, but increased the performace with this new RIOT amplier. The side benet is also the power vs cost ratio is by far greater than

before. Riot is for B2 audio equivalent to an uprising and something most can relate to. The entire Riot line oers subwoofers, speakers and ampliers. It

is the most complete series from B2 audio and will be superior in both performance and power. Given the small size of the Riot ampliers they should

also t in any vehicle.

installation 8

*Preparations

*power connectors

*Remote & RCA input

troubleshooting 9

warranty info 10

introduction 2

Design features 3

Panel layout 4

*Control panel

*speaker connection 5

*power terminal 6-7

Panel layout

remote

input

gain hpf lpf bass boost

6v 0.2v 10hz2khz50Hz0 b20khz10b

freq

0 180

bpf

speaker output

Speaker impedance 1 Ohm ~ 8 Ohm

will reach thermal at a faster rate & will eventually go into protect.

Impedance load under 1 ohm is not warranted!

We recommend using minumum10 Ga speaker cables to acquire the intended performance & eciency.

Run the speaker cables from your speakers to the amplier’s mounting location.

Ensure these are ran separately and away from high current cables and if possible the RCA cables as well.

In all cases where cables are penetrating the vechile’s chassis use grommets to protect the cable.

Connect the speaker wires according to the terminals on the speaker(s). Strip 3/8’’ / 1 cm of insulation of the end of

each cable and twist the cable strands together tightly. Make sure there are no stray strands that could touch other

cables or terminals as it can cause a short circut.

Crimp spade plugs over the end of the cable or tin the ends with solder to provide a solid terminal.

Connect the cable ends to the amplier as shown in the diagram.

17 V

6. Both speaker terminals will have rail voltage present, even after the amplier has been turned o for a while.

Measure the terminals before reconguring anything, to make sure there’s no voltage.

10 V ~ 17 V.

Ce manuel convient aux modèles suivants

Autres manuels B2 Audio Amplificateur

B2 Audio

B2 Audio MA 1000.4 Manuel utilisateur

B2 Audio

B2 Audio MANI Series Manuel utilisateur

B2 Audio

B2 Audio RAGE 5000 Manuel utilisateur

B2 Audio

B2 Audio Quattro Manuel utilisateur

B2 Audio

B2 Audio RAGE 1200.2 Manuel utilisateur

B2 Audio

B2 Audio RAGE SERIES Manuel utilisateur

B2 Audio

B2 Audio Zero.5 Manuel utilisateur

B2 Audio

B2 Audio Zero Five The Falcon Manuel utilisateur

B2 Audio

B2 Audio SLD600 Manuel utilisateur

B2 Audio

B2 Audio Quattro Manuel utilisateur

B2 Audio

B2 Audio Zero 9 Manuel utilisateur

B2 Audio

B2 Audio Zero 1 Manuel utilisateur

B2 Audio

B2 Audio Duo Manuel utilisateur

B2 Audio

B2 Audio M 12 Manuel utilisateur

B2 Audio

B2 Audio SLD5K Manuel utilisateur

B2 Audio

B2 Audio M1 Manuel utilisateur

B2 Audio

B2 Audio M1u Manuel utilisateur

B2 Audio

B2 Audio RAGE2500 Manuel utilisateur

B2 Audio

B2 Audio Zero.5 Manuel utilisateur

B2 Audio

B2 Audio RIOT16000 Manuel utilisateur

B2 Audio

B2 Audio M1u Manuel utilisateur

B2 Audio

B2 Audio zero.7 Manuel utilisateur

B2 Audio

B2 Audio Quota MKII Manuel utilisateur

B2 Audio

B2 Audio Mono Manuel utilisateur

Manuels Amplificateur populaires d'autres marques

ASTRO

ASTRO HVO V40 P Manuel utilisateur

Marantz

Marantz SUPERSCOPE BLA-545 Instructions de montage

NAD

NAD CI980 Manuel utilisateur

Technics

Technics SE-CH770 Manuel utilisateur

Harman Kardon

Harman Kardon HK6300 Manuel utilisateur

NAD

NAD T975 Manuel utilisateur

McIntosh

McIntosh MA6850 Manuel utilisateur

Electro-Harmonix

Electro-Harmonix ENGLISH MUFF’N Manuel utilisateur

Viatron

Viatron Autrix Manuel utilisateur

GME

GME GA9800 Manuel utilisateur

Atlas

Atlas CP700 Manuel utilisateur

Roland

Roland KC-1000 Manuel utilisateur

Pyle

Pyle PFMRA350BW Manuel utilisateur

Advantage

Advantage S-250 Manuel utilisateur

IRT Electronics

IRT Electronics DVA-3007 Manuel utilisateur

Dimavery

Dimavery BA-100 Series Manuel utilisateur

Sony

Sony XM-S400D Manuel utilisateur

Schertler

Schertler ROY X Manuel utilisateur