Axxess AXTC-FD3 Manuel utilisateur

AXTC-FD3

INSTALLATION INSTRUCTIONS

Product Info

ATTENTION: With the key out of the ignition,

disconnect the negative battery terminal

before installing this product. Ensure that all

installation connections are secure before

cycling the ignition to test this product.

NOTE: Refer also to the instructions included

with the aftermarket radio.

INTERFACE FEATURES

TOOLS & INSTALLATION ACCESSORIES REQUIRED

• Crimping tool and connectors, or solder gun,

solder, and heat shrink • Tape • Wire cutter

• Zip-ties

TABLE OF CONTENTS

Connections ............................................................2

Programming .........................................................3

Troubleshooting .....................................................4

Ford SWC (Steering Wheel Control)

and Data Interface 2020-Up

APPLICATIONS

• Provides accessory power

(10-amp)

• Provides wires for multimedia

radios (park brake, reverse,

speed sense)

• Retains audio controls on the

steering wheel

• Designed for non-ampliﬁed

models only

• Designed to be compatible

with all major radio brands

•

Auto detects vehicle type, radio

connection, and preset controls

• Ability to dual assign steering

wheel control buttons

• Retains memory settings even

after battery disconnection

or interface removal (non

volatile memory)

• Provides illumination output

• Micro-B USB updatable

Ford

E Series 2021-Up

Eco Sport 2020-Up

Escape 2020-Up

F250/F350/F450/F550 2020-Up

Transit 2020-Up

Transit Connect 2020-Up

INTERFACE COMPONENTS

• AXTC-FD3 interface

• AXTC-FD3 harness

• 3.5mm adapter

Note: The AXTC-FD3 does not retain SYNC.

CONNECTIONS

Front

Rear

Sub

AUX-IN

Rear View

SWC

This is to be done only in the Ford

Transit/Transit Connect 2020-Up

without SYNC. To retain backup

camera in anyother application you

must purchase the AXBUCH-FD1.

Vehicle Connectors

Radio Connections

Black - Ground

Yellow - Battery power

Red - Accessory power

Orange/White - Illumination

Blue/Pink - VSS/Speed-Sense

Green/Purple - Reverse signal

Light Green - Parking brake

Gray - Front right speaker +

Gray/Black - Front right speaker -

White - Front left speaker +

White/Black - Front left speaker -

Green - Rear left speaker +

Green/Black - Rear left speaker -

Purple - Rear right speaker +

Purple/Black - Rear right speaker -

Blue/White - Amp turn on from radio

Aftermarket Radio

(radio’s features may vary)

Reset Button

LED Light

3.5mm Adapter (for radios with a wire for SWC)

Boss (with SWC wire): Key 1 (Gray) - Brown

Kenwood / JVC (with SWC wire): Blue/Yellow - Brown

XITE: SWC-2 - Brown

Universal Radio*: Key-A or SWC-1 - Brown

Key-B or SWC-2 - Brown/White

* After programming, assign SWC buttons within radio menu

REV. 10/8/21 INSTAXTC-FD3

PROGRAMMING

Open the driver’s door, and keep open during the programming process.

Cycle the ignition on and wait (5) seconds.

3. Connect the AXTC-FD3 harness to the AXTC-FD3 interface, and then to

the wiring harness in the vehicle.

Locate the Volume Up button on the steering wheel. Program the interface

by tapping the Volume Up button at a heartbeat pace until the LED light

stops ﬂashing.

The LED light will ﬂash Green & Red while the interface programs the

radio to the steering wheel controls. Once programmed, the LED light will

go out, then produce a pattern which will identify the radio type installed

6. The LED light will go out, then once again quickly ﬂash Green & Red

while the interface programs itself to the vehicle. Once programmed,

the LED light will go out again, then turn solid Green.

7. Cycle the ignition off, then back on.

8. Test all functions of the installation for proper operation.

Green & Red LED

Green or Red LED

Green & Red LED

Green LED

VOL

Tap Volume Up

KNOWLEDGE IS POWER

Enhance your installation and fabrication skills by

enrolling in the most recognized and respected

mobile electronics school in our industry.

Log onto www.installerinstitute.edu or call

386-672-5771 for more information and take steps

toward a better tomorrow.

Metra recommends MECP

certiﬁed technicians

INSTALLATION INSTRUCTIONS

AXTC-FD3

Having difﬁculties? We’re here to help.

Contact our Tech Support line at:

386-257-1187

Or via email at:

techsupport@metra-autosound.com

Tech Support Hours (Eastern Standard Time)

Monday - Friday: 9:00 AM - 7:00 PM

Saturday: 10:00 AM - 7:00 PM

Sunday: 10:00 AM - 4:00 PM

Solid Green

Slow Red Flash

Slow Green Flash

Solid Red

Pass

Fail

Pass

Fail

Pass

Fail

Note: If the LED light shows Solid Green for Pass (indicating

everything programmed correctly), yet the steering wheel

controls don’t work, check to ensure that the 3.5mm jack is

plugged in, and also plugged into the correct jack on the radio.

Once corrected, press the reset button, then program again

Final LED Feedback

At the end of programming the LED light will turn Solid Green which

indicates programming was successful. If the LED light didn’t turn

Solid Green, reference the list below to understand which programming

section the problem may stem from.

TROUBLESHOOTING

1. 2.

QR Code Scan Here

If the interface fails to function,

press and release the reset button,

then repeat the programming

process from step 4 to try again.

Further troubleshooting steps and information

can be located at:

axxessinterfaces.com/product/AXTC-FD3

LED Light Radio

Programming

Section

Vehicle

Programming

Section

LED

Light

Reset

Button

I N T E R F A C E

AXTC-FD3

What Fits My Vehicle? See the Vehicle Fit Guide at

SALES 800-221-0932 REV. 10/11/21

Ford

Select Models

2012-Up

SWC (Steering Wheel Control)

and Data Interface

INTERFACE FEATURES

• Provides accessory power (10-amp)

• Provides wires for multimedia radios (park

brake, reverse, speed sense)

• Retains audio controls on the steering wheel

• Designed for non-ampliﬁed models only

• Designed to be compatible with all major

radio brands

• Auto detects vehicle type, radio connection,

and preset controls

• Ability to dual assign steering wheel control

buttons

• Retains memory settings even after battery

disconnection or interface removal (non

volatile memory)

• Provides illumination output

• Micro-B USB updatable

INTERFACE COMPONENTS

• AXTC-FD3 interface

• AXTC-FD3 harness

• 3.5mm adapter

Visit AxxessInterfaces.com for more detailed information about the product and up-to-date vehicle speciﬁc applications.

Ford

E Series 2021-Up

Eco Sport 2020-Up

Escape 2020-Up

F250/F350/F450/F550 2020-Up

Transit 2020-Up

Transit Connect 2020-Up

APPLICATIONS

Note: The AXTC-FD3 does not retain SYNC.

ADVANCED PROGRAMMING

AXTC SERIES

Integrate • AxxessInterfaces.com

The AXTC interface can be used in vehicles without steering wheel controls to provide retained accessory power, and also to provide wires

for multimedia radios (park brake / reverse / speed-sense). Follow the steps below to program the AXTC-CH5 for just these features.

Final LED Feedback

From the 3.5mm adapter, tie the Brown and Brown/White wires together and tape up or use a connector.

2. Connect the 3.5mm adapter to the 3.5mm jack from the AXTC-CH5 harness.

3. Program the AXTC-CH5 per the AXTC-CH5 instructions, page 3. Disregard steps 4 and 5.

•

At the end of programming the LED light will turn solid Green which indicates programming was successful

•

If the LED light turned solid Red instead, this means programming has failed. Reset the interface and try again

•

If still no success after resetting and reprogramming the interface, refer to the Vehicle Troubleshooting document for

the interface.

Ignore the steps referencing steering wheel controls.

Solid Green

Solid Red

Pass

Fail

LED Light Vehicle Programming Secon

CHANGING RADIO TYPE

AXTC SERIES

Integrate • Axxessinterfaces.com

The AXTC interface has the capability to assign (2) functions to a single button except for Volume Up and Volume Down.

This feature can be performed three different ways; through a Windows based computer using the Axxess Updater, through

the Axxess Updater app available from the Android/Apple mobile devices app store, or by following the steps below

Note: Apple mobile devices will require the use of the AX-HUB for this feature.

Attention! If more than 20 seconds elapses between steps, the procedure will abort, and the interface’s LED light

will go out. The interface may not function properly and may need to be reset and reprogrammed.

1. Program the interface to the vehicle following the vehicle specific document.

2. Turn the radio off.

3. Cycle the key off, then back on.

4. Wait until the interface’s light flashes Green one time then goes out.

5. Press and hold the Volume Down button on the steering wheel until the interface’s light turns solid Red,

then release. The light will then go out indicating that the interface is in Changing Radio Type mode.

6. Reference the Radio Legend for the radio number preferred.

7. Press and hold the Volume Up button on the steering wheel until the interface’s light turns solid Red, then

release. Radio number 1 has now been programmed. Repeat this step for the desired radio.

8. Once the desired radio has been selected, press and hold the Volume Down button on the steering wheel

until the interface’s light turns solid Red. The light will remain solid Red for 3 seconds while it stores the new

radio information. After the light goes out, turn the radio on and test the steering control wheel controls.

Pioneer / Jensen 1

Boss (type 1) / Dual / Sony 2

Kenwood 3

JVC 4

Alpine 5

Boss (type 2) 6

Clarion (type 1) 7

Clarion (type 2) 8

Boss (type 3) 9

Insane Audio 10

Magnadyne 11

Visteon / Boss (type 4) 12

JBL 13

Eclipse (type 1) 14

Eclipse (type 2) 15

Philips 16

XITE 17

Parrot 18

Valor 19

LG 20

Kicker 21

Axxera 22

Radio Brand Radio Number Radio Brand Radio Number

Radio Legend

DUAL ASSIGNMENT (LONG BUTTON PRESS)

AXTC SERIES

Integrate • Axxessinterfaces.com

The AXTC interface can assign (2) functions to a single button except for Volume Up and Volume Down. This feature

can be performed three different ways; through a Windows based computer using the Axxess Updater, through the

Axxess Updater app available from the Android/Apple mobile devices app store, or by following the steps below.

Notes:

a) Seek Up and Seek Down come pre-programmed as Preset Up and Preset Down for a long button press.

b) Apple mobile devices will require the use of the AX-HUB for this feature.

Attention! If more than 10 seconds elapses between steps, the procedure will abort, and the interface’s light will

go out. The interface may not function properly and will need to be reset and reprogrammed.

1. Program the interface to the vehicle following the vehicle specific document.

2. Turn the radio off.

3. Cycle the key off, then back on.

4. Wait until the interface’s light flashes Green 1 time then goes out.

Press and hold the desired SWC button for dual assignment for 10 seconds (or until the interface’s light flashes

rapidly Green), then release. The light will turn solid Green indicating the interface is in Dual Assignment mode

6. Reference the Dual Assignment Legend. Press and release the Volume Up button on the steering wheel the

number of times related to the desired feature for a long button press.

7. Press and release the SWC button from step 5. The interface’s light will go out indicating the information has

been stored to memory.

8. Repeat from step 5 to select another SWC button for dual assignment.

To reset an SWC button back to its default state, repeat steps 3 and 4, then press and release the Volume Down

button on the steering wheel. The AXTC-1’s light will go out, and the dual assignment feature for that button will

be erased

Volume Up * 1

Volume Down * 2

Seek Up / Next 3

Seek Down / Previous 4

Mode / Source 5

ATT / Mute 6

Preset Up 7

Preset Down 8

Power 9

Band 10

Play / Enter 11

PTT 12

On Hook 13

Off Hook 14

Fan Up * 15

Fan Down * 16

Temp Up * 17

Temp Down * 18

Feature Desired Volume Up Presses Feature Desired Volume Up Presses

Dual Assignment Legend (Long Button Press)

* Not applicable in this application

LED FEEDBACK

AXTC SERIES

Integrate • AxxessInterfaces.com

Overall LED Feedback

Radio LED Feedback

Pioneer / Jensen

Boss (type 1) / Dual / Sony

Kenwood

JVC

Alpine

Boss (type 2)

Clarion (type 1)

Clarion (type 2)

Boss (type 3)

Insane Audio

Magnadyne

Visteon / Boss (type 4)

JBL

Eclipse (type 1)

Eclipse (type 2)

Philips

XITE

Parrot

Valor

Kicker

Axxera

3 (Boss)

Radio LED Paern Keynotes (reference below)

1) If the LED pattern shows JVC, change the radio type to Kenwood. Refer to the

Changing Radio Type

document.

If the LED pattern shows Alpine, but an Alpine radio isn’t installed, make sure the 3.5mm jack is plugged into the radio.

3) If no SWC, change the radio type to the opposite radio type. Refer to the

Changing Radio Type

document.

4) AX-SWC-PARROT required (sold separately). The software in the radio must be rev. 2.1.4 or higher.

LED Light

Solid Green

Slow Red Flash

Slow Green Flash

Solid Red

Radio Programming Secon

Pass

Fail

Pass

Fail

Vehicle Programming Secon

Pass

Fail

RADIO TROUBLESHOOTING

AXTC SERIES

Integrate • AxxessInterfaces.com

If the AXTC interface’s LED light didn’t go out at the end of the radio programming sequence, or showed the wrong radio installed*, follow the

steps below to trace down where the problem may lie. The final LED feedback light will also flash Red slowly or turn solid Red, instead of turning

solid Green. If any of the following steps are performed, reset and reprogram the interface per the vehicle specific document. Take note where

SWC is worded means Steering Wheel Control.

* Reference the Radio LED Feedback table at the end of this document.

The 3.5mm jack from interface should be plugged into the SWC Input from the radio. Make sure it isn’t

plugged into the Bluetooth Mic or AUX Input. If unsure which input to use, refer to the manual provided with

the radio, or contact the radio Manufacturer.

Note: Some radios use a wire an for SWC instead

Reference the Radio LED Feedback table. Boss, Clarion, and Eclipse have different radio types and the wrong

radio type may have been auto detected. Reference the Changing Radio Type document to change the radio

type. Also refer to the radio specific troubleshooting steps on the following page.

If all troubleshooting steps have been performed and the interface still doesn’t go solid

Green

at the end of

the final programming sequence, update the interface to the latest firmware, then try programming once

more. If the interface still doesn’t go solid

Green

, contact Tech Support at 1-800-253-TECH. Take note to

be prepared to perform some tests in the vehicle when you contact Tech Support, and have the Product ID

Number on the bottom of the interface noted.

Is the

3.5mm jack

connected?

Was the

correct

radio type

detected?

Update

the

interface

Back of interface

Continued on the next page

XXXX-XXX-XXXX

Update

Port

Product

ID Number

Autres manuels Axxess Automobile électronique

Axxess

Axxess AX-DSP-HYKIA2 Manuel utilisateur

Axxess

Axxess AX-LR90102 Manuel utilisateur

Axxess

Axxess AXDIS-BW122 Manuel utilisateur

Axxess

Axxess AX-DSPX-HYKIA4 Manuel utilisateur

Axxess

Axxess AX-LR902 Manuel utilisateur

Axxess

Axxess GMOS-LAN-06 Manuel utilisateur

Axxess

Axxess AXDSPX-HK4 Manuel utilisateur

Axxess

Axxess ASWC Manuel utilisateur

Axxess

Axxess RFASWC Manuel utilisateur

Axxess

Axxess AX-JP901 Manuel utilisateur

Axxess

Axxess AXDSPX-FD3 Manuel utilisateur

Axxess

Axxess AX-MLINK-HD Manuel utilisateur

Axxess

Axxess AX-FT901 Manuel utilisateur

Axxess

Axxess AX-ADDCAM Manuel utilisateur

Axxess

Axxess ASWC-TOY-LEX Manuel utilisateur

Axxess

Axxess ABTI-GM4 Manuel utilisateur

Axxess

Axxess AX-ADXSVI Series Manuel utilisateur

Axxess

Axxess GMOS-MOST-02 Manuel utilisateur

Axxess

Axxess AX-DSPX-HYKIA2 Manuel utilisateur

Axxess

Axxess AX-LR904 Manuel utilisateur

Axxess

Axxess AX-ADFD02 Manuel utilisateur

Axxess

Axxess TRIGGER Manuel utilisateur

Axxess

Axxess ABTI-GM1 Manuel utilisateur

Axxess

Axxess AX-PO904 Manuel utilisateur

Manuels Automobile électronique populaires d'autres marques

GoldCruise

GoldCruise GC90Ci Manuel utilisateur

DRG

DRG LC 120 Manuel utilisateur

Blue Ox

Blue Ox BX8848 Manuel utilisateur

Dometic

Dometic MAGICWATCH MWE890K Manuel utilisateur

Perfect Power

Perfect Power SMT8-T5 Manuel utilisateur

Honeywell

Honeywell Thor VM3A Manuel utilisateur

Waeco

Waeco MagicWatch MWE250 Manuel utilisateur

Rydeen

Rydeen BKM091 Manuel utilisateur

Skoda

Skoda 5E0 054 630 Manuel utilisateur

VDO

VDO SENDER UNIT 2159-0 Manuel utilisateur

iDataLink

iDataLink maestro Rr Manuel utilisateur

Audiovox

Audiovox PRO-PDA15 Manuel utilisateur

Movon

Movon MDAS-3LFFHD Manuel utilisateur

Pioneer

Pioneer Comfort adapter CA-D-PI.150 Manuel utilisateur

Dietz

Dietz 1110 Manuel utilisateur

Crux

Crux RVCFD-79 Manuel utilisateur

Nonda

Nonda ZUS Manuel utilisateur

iDataLink

iDataLink Maestro Manuel utilisateur