AXIWI AT-320 Manuel utilisateur
AXIWI
Digital Wireless Audio System
AXIWI AT-320
User Guide
Safety Precautions
Observe the following precautions to ensure user safety
and proper use of the device.
●Avoid exposing the AXIWI AT-320 to dramatic changes in temperature
or humidity. Otherwise, you may risk distortion of the product
exterior or product malfunction.
●Listening to sound at high volumes may damage your hearing.
Background noise, as well as continued exposure to high volume
levels, can make sounds seem quieter than they actually are.
Turn on the audio and check the volume before inserting anything
in your ear.
●You should also pay attention to how long you listen to audio at
high volume. The louder the volume, the less time required before
your hearing may be affected. If you experience ringing in your
ears or hear muffled speech, stop listening and have your hearing
checked.
●This device is designed for short-distance communication.
Use the device only in countries where the use of 2.4GHz
bandwidth is permitted.
●Ensure that the device’s battery charging terminal does not
come in contact with an electrically charged object.
●Do not disassemble the device.
●Ensure the battery of the device is sufficiently charged before use.
-1-
Index to Product Content:
-2-
How to Turn On/Off; Master/transmitter mode:
Turning On
1. Press the power button for about 2-3 seconds whilst pressing the volume up button.
2. When the device is booted in“master mode”, the LED light remains lit continuously.
Turning Off
1. Press the power button for about 2-3 seconds.
2. The device is turned off when all LED lights are off.
-3-
How to Turn On/Off; Slave/receiver mode:
Turning On:
1. Press the power button for about 2-3 seconds.
2. When the device is booted in “slave mode”, the LED light will blink
and will continue to do so during the time the device is turned on.
.
Turning Off:
1. Press the power button for about 2-3 seconds.
2. The device is turned off when all LED lights are off.
-4-
How to change Channels:
The AXIWI AT-320 can operate on 4 different channels or frequencies. To change channel press the
S-button on the front side while pressing the volume up button.
The channel LEDs will light up in turn by the order of channels.
((Blue -> Orange -> Red -> Green -> back to Blue -> etc.)
* Channel Memory Function:
When you turn off the device and turn it on again, the device will remember
what channel was used before it was switched off.
-5-
Slave Mode - How to request the“permission to speak”:
1. On the device which currently is in slave mode briefly press the S-button on the front side.
2. All LED lights will light up and a beep can be heard through the headset off all devices tuned into
the current channel.
3. The device is now in speak mode, allowing everyone tuned into the channel to hear the temporary
speaker.
* This function is to allow slave mode units to request the permission to speak. Permission is given on
the first come first serve basis and maximum two slave mode units can get the permissions
simultaneously.
Alternative software options are available to change the behavior of the permission to speak function.
Please contact your supplier for more information on the available options.
-6-
Slave Mode - How to cancel the permission to speak:
1. Briefly press the S-button on the front side of the slave device currently in permission to speak
mode
2. A beep will sound and the four lit LED lights will return to a single blinking LED light.
* This function is to allow a slave mode device to cancel its permission to speak by the user
himself/herself. When in normal “listening mode”, only one LED for the specific channel on the unit
will be blinking, instead of four lit LEDs.
-7-
Master Mode –How to cancel the permission to speak for units in slave mode:
1. Press the S-button on the front side of the “master mode”unit to cancel ALL the permissions to
speak granted to “slave mode”units.
2. When the permissions are cancelled successfully, you can hear two beeping sounds.
* Automatic cancellation of the permission to speak mode: When the distance between the master
mode unit and the slave mode unit gets too long and communication between the two units becomes
impossible, the permission to speak for the slave mode unit is automatically cancelled.
-8-
Master Mode –How to cut off the permission to speak function for all slave units:
1. Press and hold the volume down button for about 3-5 seconds on the master mode unit.
2. When the cut-off is made you can hear two beeping sounds through the headset of the master
mode unit.
The cut-off function is to allow the master mode unit to cut off the permission to speak mode from ALL
slave units. When active none of the slave units on the current channel can use the permission to
speak function.
Master Mode - How to release the cut-off of the permission to speak function:
1. Press and hold the volume down button for about 3-5 seconds on the master mode unit.
2. When the cut-off is released you can hear one beeping sound through the headset of the master
unit.
The user with the “Master” unit can switch off the Speak function of all slave units for a short moment.
If so, all slave units are being switched to the same channel, but this is not being communicated. All
units in “Slave” modus cannot use their speak function.
-9-
Autres manuels pour AT-320
2
Autres manuels AXIWI Système stéréo
