Axis T90C10 Manuel utilisateur

ENGLISH DEUTSCH ITALIANO ESPAÑOL

USER GUIDE

FRAN

AIS

AXIS T90C10 Fixed Dome IR-LED

AXIS T90C20 Fixed Dome IR-LED

ENGLISH

Safeguards

Please read through this User Guide carefully before installing the product. Keep the User Guide for further

reference.

CAUTION!

• When transporting the Axis product, use the original packaging or equivalent to prevent damage to the

product.

• Store the Axis product in a dry and ventilated environment.

• Only use handtools when installing the Axis product, the use of electrical tools or excessive force could

cause damage to the product.

• Do not use chemicals, caustic agents, or aerosol cleaners. Use a damp cloth for cleaning.

• Only use accessories and spare parts provided or recommended by Axis.

• Do not attempt to repair the product by yourself, contact Axis or your Axis reseller for service matters.

IMPORTANT!

• This Axis product must be used in compliance with local laws and regulations.

AXIS T90C10/T90C20 Fixed Dome IR-LED User Guide Page 5

ENGLISH

AXIS T90C10/T90C20 Fixed Dome IR-LED

This guide provides instructions for installing the AXIS T90C10/ AXIS T90C20 IR-LED with the

following fixed dome cameras:

• AXIS P3343-VE

• AXIS P3344-VE

• AXIS P3346-VE.

To install the camera, refer to the installation guide supplied with the product.

The contents of this guide are as follows:

Package Contents

. See below.

Installation

, on page 8.

Specifications

, on page 12.

Package Contents

Item Models/variants/notes

Lighting Module • PoE Cat 5 cable

(for AXIS T90C20 Fixed Dome IR-LED)

• 18-56V DC Power Control cable

(for AXIS T90C10 IR-LED)

Printed materials AXIS T90C10/T90C20 Fixed Dome IR-LED User Guide

(this document), Axis Warranty Document

Page 6 AXIS T90C10/T90C20 Fixed Dome IR-LED User Guide

Hardware Overview

AXIS P33 Fixed Dome camera

Photocell

IR-LED

PoE Cat 5 or 18-56 V DC Power

(pre-mounted)

5-meter cable

Specifications subject to change without notice. Installation to be carried out by trained and qualified personnel.

AXIS T90C10/T90C20 Fixed Dome IR-LED User Guide Page 7

ENGLISH

Recommendations

This Axis product is delivered with the LED block facing the front and this positioning is appropriate

for most installations; it is however possible to move the LED block to face other directions. See

page 10.

Use screws appropriate for your wall material.

20-30m

Max illumination

Less illumination Less illumination

120˚

Page 8 AXIS T90C10/T90C20 Fixed Dome IR-LED User Guide

Installation

Notes:

• When the IR-LED is installed, the camera cables can only be routed through the wall (not along the wall).

•The

IR-LED is controlled by the level of ambient light which is detected by the unit's photocell. Ensure that

the photocell is not obstructed or covered.

1. If the camera is already installed, disconnect power from the camera; remove the weather

shield, and the dome cover on the camera; remove the unit casing from the mounting bracket;

detach the camera unit.

If the camera is not already installed, attach the mounting bracket to the wall. Please check the

camera’s installation guide for this and further installation procedures.

2. Remove the side lid from the unit casing; save the screw.

If the camera lens is to face right or left, please read the information on page 10 before you

proceed.

3. Remove the gasket from one of the side holes and

from the corresponding back hole in the unit casing,

for cabling. (The cable for the IR-LED should enter

the hole to the left in the unit casing)

Route the IR-LED cable through the side hole and

through the back hole in the unit casing.

4. Force the 2 gaskets on the cable through the side

hole.

Mounting bracket

Unit casing

Dome cover

Weather shield

Side holes

Back hole

Side lid

Screw

Unit casing

Gaskets in side

and back holes

AXIS T90C10/T90C20 Fixed Dome IR-LED User Guide Page 9

ENGLISH

5. Plug the gaskets into the side and back holes. The gaskets should fit snugly in the holes with no

folds or bends.

6. Place the IR-LED beneath the unit casing

aligning the screw hole on the back of the

IR-LED with the screw hole in the unit

casing; screw the IR-LED on to the unit

casing with the single screw.

7. Attach the unit casing to the mounting

bracket.

8. For vandal-resistant installation do the following:

a. Detach the cover on the IR-LED.

b. Screw the IR-LED to the wall with 2 screws.

c. Replace the cover after ensuring the gasket is in place.

9. Connect the network cable from the IR-LED to the PoE switch or midspan (AXIS T90C20); or

connect the DC cable to the PSU (AXIS T90C10).

10. To complete the camera installation please refer to the installation guide provided with the

network camera.

Screw IR-LED

Back view

Screw here

Front view

Page 10 AXIS T90C10/T90C20 Fixed Dome IR-LED User Guide

AXIS T90C20

When camera lens faces left

1. Remove 2 screws located on the top on either side of the LED block.

2. Unscrew the ground wire from the screw hole to the left and attach to a screw hole to the

right.

3. Align the LED block with the screw holes to the left and fasten the 2 screws again.

When camera lens faces right

1. Remove 2 screws located on the top on either side of the LED block.

2. Unscrew the ground wire from the screw hole to the left and attach to a screw hole to the

right.

3. Loosen the cable gland and pull a greater length of the cable so it can reach the left side of the

IR-LED.

4. Remove 2 screws on the control board and fasten the control board to the left.

5. Fix the LED block where the control board was with 2 screws.

LED block

2 screws on LED block

LED block to the left

LED block to the right

2 screws on control

board

LED block

Control board

LED block to the center

Cable gland

Ground wire

Autres manuels pour T90C10

Ce manuel convient aux modèles suivants

Table des matières

Langues :

Autres manuels Axis Caméra de sécurité

Axis

Axis P5654-E Mk II Manuel utilisateur

Axis

Axis Q1615-E MKII Manuel utilisateur

Axis

Axis Q35 Series Manuel utilisateur

Axis

Axis M4218-LV Manuel utilisateur

Axis

Axis AXIS P3235-LV Manuel utilisateur

Axis

Axis P1343-E Manuel utilisateur

Axis

Axis P5635-E Manuel utilisateur

Axis

Axis Q6035-E PTZ Manuel utilisateur

Axis

Axis Axis 216FD Manuel utilisateur

Axis

Axis P1353 Manuel utilisateur

Axis

Axis S P13-E Manuel utilisateur

Axis

Axis AXIS 212 PTZ-V Manuel utilisateur

Axis

Axis M5013-V Manuel utilisateur

Axis

Axis 211W Manuel utilisateur

Axis

Axis 0530-001 Manuel utilisateur

Axis

Axis M31 SERIES Manuel utilisateur

Axis

Axis M5013 Manuel utilisateur

Axis

Axis M3045-V Manuel utilisateur

Axis

Axis M5000 Manuel utilisateur

Axis

Axis M1033-W Manuel utilisateur

Axis

Axis Q8685-E Manuel utilisateur

Axis

Axis M11 Network Camera Series Manuel utilisateur

Axis

Axis M1135 Manuel utilisateur

Axis

Axis NETWORK CAMERA 2100 Manuel utilisateur

Manuels Caméra de sécurité populaires d'autres marques

Okina USA

Okina USA SIR36-870VF650LP Manuel utilisateur

Divio

Divio NDR155PA Manuel utilisateur

Canon

Canon VB-C500D Manuel utilisateur

Easy Access

Easy Access EasyGuard Manuel utilisateur

Vivotek

Vivotek FD9389-EHV-v2 Manuel utilisateur

TUYA

TUYA COSMO W2 Manuel utilisateur

Eusso

Eusso UNC7500-IR Guide de configuration

urmet domus

urmet domus 1096/204 Manuel utilisateur

VC VC20 series Manuel utilisateur

ieGeek

ieGeek DD201 Manuel utilisateur

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Manuel utilisateur

Vicon

Vicon V662-D-1 Mode d'emploi

Grundig

Grundig GCH-K0274P Manuel utilisateur

Lorex

Lorex VANTAGE LBC7032 Manuel utilisateur

4xem

4xem WPT Manuel utilisateur

Samsung

Samsung SCV-3082 Manuel utilisateur

Vitek

Vitek VTC-C544 Manuel utilisateur

Lumens

Lumens VC-A50PNW Manuel utilisateur