Axis AXIS T95A00 Manuel utilisateur

ENGLISH DEUTSCH ITALIANO ESPAÑOL

INSTALLATION GUIDE

FRAN

AIS

AXIS T95A00 Dome Housing

AXIS T95A10 Dome Housing

AXIS T95A00/T95A10 Dome Housing Page 3

ENGLISH

AXIS T95A00/T95A10 Dome Housing

The AXIS T95A00/T95A10 Dome Housing can be used in both indoor and outdoor camera

installations. Follow these instructions to complete the installation of the AXIS T95A00/T95A10

Dome Housing and Axis network camera.

Warning! High voltage - the electrical connection must be made by an authorized electrician.

Please observe relevant national and local regulations for the installation.

•“Package Contents” on page 4

•“Installation” on page 5

•“Technical Specifications” on page 16

Safety Rules

Only qualified technical personnel may install this device.

• Disconnect power before any technical work on the appliance.

• Do not use old or worn out power cables.

• Never make changes or connections that are not shown in this handbook; improper use of

the appliance may cause serious hazard and may damage the product.

• Use original spare parts. Non-original spare parts could cause fire, electrical discharge, or

other hazards.

• Before installing the device, check the supplied material to make sure it corresponds with

the order specification.

• Please retain this document for future reference.

Axis Network Cameras

The AXIS T95A00/T95A10 Dome Housing supports the following camera models:

Camera Model: Note:

• AXIS 213 PTZ Before you begin, make sure that the AXIS

T95A00/T95A10 Dome Housing package contents, and

the required cables, tools, and documentation are avail-

able. See “Package Contents” on page 4.

• AXIS 214 PTZ

• AXIS 215 PTZ

• AXIS 231D+/232D+

• AXIS 233D

Page 4 AXIS T95A00/T95A10 Dome Housing

Package Contents

Large box:

(1) AXIS T95A00/T95A10 Dome Housing

Small box:

(2) Domes - transparent and smoked

(1) Fastening ring for dome

(1) Rubber gasket for dome

(4) M3x10mm screws for fastening ring

Plastic bag:

(1) Plate for cable glands

(1) Gasket for the cable gland plate

(1) M20 cable gland

(1) M16 cable gland

(1) M12 cable gland

(1) Plastic nut for M20 cable gland

(1) Plastic nut for M16 cable gland

(1) Plastic nut for M12 cable gland

(3) M3x10mm screws

(3) M3x8mm screws

(4) M4x10mm screws

(3) M3 nuts

(4) M4 nuts

(4) Lock washers

(1) 3mm Allen key

Plastic bag:

(1) Desiccant salt bag

Additional parts:

(1) Power cable for AXIS 213 PTZ, AXIS 214 PTZ, and AXIS 215 PTZ

(1) Ethernet cable with 90 degree angle for AXIS 231D+/232D+

AXIS T95A00/T95A10 Dome Housing Page 5

ENGLISH

Tools/ Parts not included

Other required parts

Note:

Not all screws provided are required for all camera installations.

Installation

Follow these steps indoors before the installation outdoor to save time at the installation site.

Attach Universal Adaptor to camera

1. Remove the top cover of the housing (with four screws) from the housing using the 3mm allen

key.

2. For AXIS T95A00 Dome Housing only - remove the two connectors (with black and blue cables)

attached to the circuit board on top of the Universal Adapter.

3. Loosen the three screws holding the Universal Adaptor. Rotate slightly and remove the

Universal Adaptor from the housing.

4. Attach the Universal Adaptor to the camera. For details see page 14.

Note:

Do not install the camera in the housing at this point. Transport it carefully to the place of

installation first.

Phillips screw driver

Ceiling bracket for AXIS 231D+/232D+ (supplied with the network camera)

Adjustable wrench

Mounting bracket See www.axis.com for available brackets and accessories

Power cable Examples:

AWG20, 100-240 VAC cable (AXIS T95A00 Dome Housing)

AWG22, 24 VAC cable (AXIS T95A10 Dome Housing)

Network cable CAT 5 shielded twisted pair (STP) cable recommended

Soft cloth Recommended for protecting the dome while installing the housing

Top cover Black cable Blue cable

Universal Adaptor

Page 6 AXIS T95A00/T95A10 Dome Housing

Fix the dome cover to the housing

Place the fastening ring over the dome. Insert the four

10mm M3 screws, so you hold the ring, the dome

cover, and the gasket together. Fix the dome cover

(transparent or smoked) at the bottom of the housing.

AXIS 213 PTZ, AXIS 214 PTZ, and AXIS 215 PTZ power connection

Connect the (provided) power cable to the 12 VDC output as shown in the picture.

AXIS T95A00/T95A10 Dome Housing output 12V DC

Camera power cable Housing power connector

black

red

GND

12 V

fastening ring

Housing

Rubber gasket

Dome

Fastening ring

Network camera power cable

12V DC

brown cable

power connector

AXIS T95A00/T95A10 Dome Housing Page 7

ENGLISH

AXIS 231D+/232D+ and AXIS 233D power connection

1. Unplug the connector from the 12 VDC power supply opposite the bracket opening as shown in

the illustration below.

2. Remove the 2-pin green connector block from the cables.

3. Connect the cable to the camera’s power connector as described below:

AXIS 231D+/232D+

• AXIS T95A00 Dome Housing (24V DC)

• AXIS T95A10 Dome Housing (24V AC)

Connect the brown cable to the 24V AC/DC pins on the AXIS

231D+/232D+ connection module (see illustration).

Note:

The AXIS 231D+/232D+ connection module contains a

rectifier so the cables can be connected either way.

24V

12 VDC

power connector

Brown cable

remove green

connector

block

AXIS 231D+/232D+ Connection module

24V AC/DC

Page 8 AXIS T95A00/T95A10 Dome Housing

AXIS 233D

As the camera is not yet installed in the housing, this is a preparatory step

showing how to connect the brown cables from the 24V connector to the

8-pin green connector block (supplied with the camera). When the

camera is later installed in the housing, this connector block will then be

connected to the camera itself. Referring to the connection diagram on

the right, connect the brown cables for your version of the T95A.

• AXIS T95A00 Dome Housing (24V DC)

Connect +24V to AC/DC+

Connect -24V to GND/DC-

• AXIS T95A10 Dome Housing (24V AC)

Connect +24V to AC/DC+

Connect -24V to AC.

Prepare the cable gland plate

Fix the 3 cable glands to the cable gland plate and place the cable gland plugs on them. Insert the

four M3 screws through the gasket and plate.

The preparation for the network camera installation is now complete.

AXIS 233D

Connector

AC/DC+

GND/DC-

12V out

GND

Line out

GND

Line/Mic in

AXIS T95A00/T95A10 Dome Housing Page 9

ENGLISH

Install the mounting bracket

Note:

Make sure all cables are in place but not powered, before you install the bracket. Keep

cables unpowered until the installation is complete.

1. Install the bracket for the AXIS T95A00/T95A10 Dome Housing on a wall and make sure that

the screws and plugs are appropriate for the wall (wood, metal, concrete, or any other), and

suitable for the weight of the housing. To install the bracket in the correct direction, see figure

below.

2. Pull a sufficient length of the cables through the bracket for the housing and camera

(approximately 50 cm).

Note:

Visit the Axis web site at www.axis.com for a comprehensive list of the available brackets

and accessories.

3170

182

150

230

140

110

Page 10 AXIS T95A00/T95A10 Dome Housing

Mount the housing to the bracket

Notes:

• Ensure that the bracket is securely fastened, and cables are pulled through it before mounting the

camera housing. Ensure that no power is connected to the cables.

• It is recommended that you place a soft, clean cloth (not included) into the dome to ensure it

remains clean until the time when you need to mount the camera.

1. If the top cover of the housing was attached to facilitate transportation, detach it again at this

point.

2. Position the AXIS T95A00/T95A10 Dome Housing against the bracket, making sure to pull the

cables (power, Ethernet, and I/O cables if applicable) into the housing, and tighten the two

25mm M5 allen key screws (included with the bracket).

3. Pull the cables through the cable glands, and secure the hole in the bracket with the cable

gland plate. Ensure the cables are securely fastened in the cable glands.

4. Remove the protective cloth (if you have used one) from the dome, and remove traces of dust.

Install the camera in the housing

1. Make sure power is disconnected from the housing before installing the camera.

2. Connect the network cable to the Ethernet port in the camera.

3. Connect the power cable to the camera.

4. If applicable, connect the I/O cables to the connectors as described in the installation guide

supplied with the camera.

5. Lower the Universal Adaptor with the attached camera into the AXIS T95A00/T95A10 Dome

Housing and tighten the 3 screws.

6. Connect power to the housing as described below.

•“For AXIS T95A00 Dome Housing” on page 11

•“For AXIS T95A10 Dome Housing” on page 12

Autres manuels pour AXIS T95A00

Ce manuel convient aux modèles suivants

Table des matières

Langues :

Autres manuels Axis Caméra de sécurité

Axis

Axis P3925-LRE Manuel utilisateur

Axis

Axis Q6045-C Mk II Manuel utilisateur

Axis

Axis TNS-2 series Manuel utilisateur

Axis

Axis Q6114-E Manuel utilisateur

Axis

Axis F8214 Manuel utilisateur

Axis

Axis AXIS 212 PTZ Manuel utilisateur

Axis

Axis Q6074-E PTZ Manuel utilisateur

Axis

Axis P3224-VE Mk II Manuel utilisateur

Axis

Axis Q6100-E Manuel utilisateur

Axis

Axis Q3709-PVE Manuel utilisateur

Axis

Axis Q6034-E Manuel utilisateur

Axis

Axis P3344-VE Manuel utilisateur

Axis

Axis M3004-V Manuel utilisateur

Axis

Axis Fixed Dome Network Camera AXIS P3301-V Manuel utilisateur

Axis

Axis Q8685-LE Manuel utilisateur

Axis

Axis Q60 Series Manuel utilisateur

Axis

Axis P5534-E Manuel utilisateur

Axis

Axis 0588-001 Manuel utilisateur

Axis

Axis AXIS M3025-VE Manuel utilisateur

Axis

Axis Q6032 Manuel utilisateur

Axis

Axis D201-S XPT Q6075 Manuel utilisateur

Axis

Axis Q6135-LE Manuel utilisateur

Axis

Axis P33 series Manuel utilisateur

Axis

Axis AXIS 2420 W/Lens Manuel utilisateur

Manuels Caméra de sécurité populaires d'autres marques

Okina USA

Okina USA SIR36-870VF650LP Manuel utilisateur

Divio

Divio NDR155PA Manuel utilisateur

Canon

Canon VB-C500D Manuel utilisateur

Easy Access

Easy Access EasyGuard Manuel utilisateur

Vivotek

Vivotek FD9389-EHV-v2 Manuel utilisateur

TUYA

TUYA COSMO W2 Manuel utilisateur

Eusso

Eusso UNC7500-IR Guide de configuration

urmet domus

urmet domus 1096/204 Manuel utilisateur

VC VC20 series Manuel utilisateur

ieGeek

ieGeek DD201 Manuel utilisateur

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Manuel utilisateur

Vicon

Vicon V662-D-1 Mode d'emploi

Grundig

Grundig GCH-K0274P Manuel utilisateur

Lorex

Lorex VANTAGE LBC7032 Manuel utilisateur

4xem

4xem WPT Manuel utilisateur

Samsung

Samsung SCV-3082 Manuel utilisateur

Vitek

Vitek VTC-C544 Manuel utilisateur

Lumens

Lumens VC-A50PNW Manuel utilisateur