Axis AXIS 207W Manuel

AXIS 207W Network Camera

Technical Information

Version 1.0 page 1 of 5

A few things that should help you get the AXIS 207W

connected to your network.

It’s not always easy to install new products on your network and this document describes some of

the things you may need to configure to get your AXIS 207W connected to your Wireless network.

Access Point/ Routers

The AXIS 207W has been tested with a lot of different Access Points and Routers from different

manufacturers. If you’re having problems with connecting your camera to the network first make

sure that the Access Point/ Router you are using is upgraded with the latest Firmware. Also make

sure that there are no settings in the Access Point/Router preventing the camera to connect. The

best thing is to use the default settings and then add more security features when you know that

the connection is working. A few things to control in the Access Point/Router:

1. ESSID

2. MAC address filtering (don’t forget to add the camera if used)

3. IP address filtering (don’t forget to add the camera if used)

4. Encryption (use the same encryption setting as in the camera)

Picture is taken from the web interface in Netgear WGR 614.

AXIS 207W Network Camera

Technical Information

Version 1.0 page 2 of 5

Signal strength

It’s important to have good signal strength. In the AXIS 207W web interface you can find info

about the signal strength between the Axis 207W and the Access Point/Router:

http://IP-address/admin/wlan.shtml?id=9

You can see the signal strength to Access Point/Router both if you’re connected to the camera

Wirelessly or through a network cable. The recommendation is to have signal strength at 70% or

above and the minimum should be 50%.

If you would like to get better signal strength there are a few options of what you can do to

improve these figures:

1. Move the AXIS 207W closer to the Access Point/Router.

2. Rotate the antennas.

3. Change position of the camera or the Access Point/Router if they are placed behind any

obstacle.

4. Change Wireless channel that are used in the Access Points/Router.

5. Turn off other equipment that might interfere the signal

If many Access Points/Routers are placed in the same environment they will interfere with each

other if they are using the same or nearby channels. By using channel 1, 6 and 11 you can place

the devices in the same area without any interference.

AXIS 207W Network Camera

Technical Information

Version 1.0 page 3 of 5

Managed mode/Ad-Hoc mode

The AXIS 207Ws station mode is default configured to Auto, which means that it will connect to

both Access Points/Router in managed mode and other devices in Ad-Hoc mode. This means that if

you have more wireless equipment such as other wireless cameras or Laptops with the same ESSID

as the AXIS 207W, the camera might connect to them instead of the Access Point/Router.

Note: If the camera is connected to the Access Point/Router and then looses the connection

for a short second it might connect to another device on the network in Ad-Hoc mode

and the other network devices will then loose the connection to it!

Changing the station mode in the AXIS 207W from Auto to Managed mode can prevent this. Go to

Plain Configuration in the web interface and set the correct value and press the save button.

http://IP-address/admin/config.shtml?group=Network

AXIS 207W Network Camera

Technical Information

Version 1.0 page 4 of 5

Encryption

It’s of course extremely important to set up the same configuration in the AXIS 207W as in the

Access Point/Router. If they are not using the same encryption type and key there will be no

communication. First select if you would like to use WEP or WPA/WPA2. If WEP is used it’s

recommended to use open mode since shared key is not secure to use. The best choice would be to

use WPA/WPA2 with a Passphrase though since this method is more secure. Use a Passphrase that

can’t be guessed by anyone and double check that you use the same key in all devices that you

would like to connect.

Network settings

If you’re switching between wired and wireless connection it’s easier if the IP address configuration

is set up with the same IP address in both cases.

AXIS 207W Network Camera

Technical Information

Version 1.0 page 5 of 5

UPnP

In some cases UPnP affects the Wireless connection and in these cases it’s recommended to switch

this feature off. This is done from this page:

http://IP-address/admin/UPnP.shtml

Autres manuels pour AXIS 207W

Table des matières

Autres manuels Axis Caméra de sécurité

Axis

Axis M1143-L Manuel utilisateur

Axis

Axis M5014-V Manuel utilisateur

Axis

Axis P1465-LE-3 Manuel utilisateur

Axis

Axis Fixed Dome Network Camera AXIS P3301 Manuel utilisateur

Axis

Axis Q6055 Manuel utilisateur

Axis

Axis P5512 PTZ Manuel utilisateur

Axis

Axis P33 series Manuel utilisateur

Axis

Axis Q60 Series Manuel utilisateur

Axis

Axis AXIS P1357-E Manuel utilisateur

Axis

Axis AXIS 212 PTZ-V Manuel utilisateur

Axis

Axis P3727-PLE Manuel utilisateur

Axis

Axis M3104-LVE Manuel utilisateur

Axis

Axis P14 Series Manuel utilisateur

Axis

Axis Axis 2130 Manuel utilisateur

Axis

Axis T90C10 Manuel utilisateur

Axis

Axis 0924-001 Manuel utilisateur

Axis

Axis P3245 Series Manuel utilisateur

Axis

Axis P3905-R Mk III Manuel utilisateur

Axis

Axis M5075 Manuel utilisateur

Axis

Axis Q1775 Manuel utilisateur

Axis

Axis 31922 Manuel utilisateur

Axis

Axis P3367-V Manuel utilisateur

Axis

Axis Q3505-V Mk II Manuel utilisateur

Axis

Axis M3011 Manuel utilisateur

Manuels Caméra de sécurité populaires d'autres marques

Okina USA

Okina USA SIR36-870VF650LP Manuel utilisateur

Divio

Divio NDR155PA Manuel utilisateur

Canon

Canon VB-C500D Manuel utilisateur

Easy Access

Easy Access EasyGuard Manuel utilisateur

Vivotek

Vivotek FD9389-EHV-v2 Manuel utilisateur

TUYA

TUYA COSMO W2 Manuel utilisateur

Eusso

Eusso UNC7500-IR Guide de configuration

urmet domus

urmet domus 1096/204 Manuel utilisateur

VC VC20 series Manuel utilisateur

ieGeek

ieGeek DD201 Manuel utilisateur

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Manuel utilisateur

Vicon

Vicon V662-D-1 Mode d'emploi

Grundig

Grundig GCH-K0274P Manuel utilisateur

Lorex

Lorex VANTAGE LBC7032 Manuel utilisateur

4xem

4xem WPT Manuel utilisateur

Samsung

Samsung SCV-3082 Manuel utilisateur

Vitek

Vitek VTC-C544 Manuel utilisateur

Lumens

Lumens VC-A50PNW Manuel utilisateur