Axis 215 PTZ Manuel utilisateur

ENGLISH FRANCAIS DEUTSCH ESPAÑOL

ITALIANO

AXIS 215 PTZ

Installation Guide

AXIS 215 PTZ Installation Guide Page 3

ENGLISH

AXIS 215 PTZ

Installation Guide

This installation guide provides instructions for installing the AXIS 215 PTZ Network

Camera on your network. For all other aspects of using the product, please see the User’s

Manual, available on the CD included in this package, or from www.axis.com/techsup

Installation steps

1. Check the package contents against the list below.

2. Hardware overview. See page 4.

3. Mount the hardware. See page 5.

4. Assign an IP address. See page 10.

5. Set the password. See page 13.

Package contents

Item Models/variants/notes

Network camera • AXIS 215 PTZ 50Hz (PAL)

• AXIS 215 PTZ 60Hz (NTSC)

Power adapter 12V DC

Power adapter mains

cable

(country-specific)

• Europe

•UK

• Australia

• USA/Japan

•Argentina

•Korea

4-pin block connector For connecting external devices to the I/O terminal connector

Drop ceiling mounting kit 1 inner bracket, 1 outer bracket

Plastic domes x 2 1 x for surface mounting

1 x for drop ceiling mounting

Screwdriver Resitorx T20

Screw kit • 1 x safety wire 1m (3.3 ft)

• 2 x plug 30x3.4-4mm

• 2 x screw ST4.2x38

• 4 x screw M4x10

• 1 x screw M4x4

• 2 x screw M4x10 resitorx

Template Use to mark positions for surface/drop ceiling mounting

CD AXIS Network Video Product CD, including product documentation,

installation tools and other software

Printed Materials AXIS 215 PTZ Installation Guide (this document)

Axis Warranty Document

Important!

This product must be used in

compliance with local laws

and regulations.

Page 4 AXIS 215 PTZ Installation Guide

Hardware overview

Surface mounted unit

Drop ceiling mounted unit

AXIS 215 PTZ Installation Guide Page 5

ENGLISH

Weights

• Camera: 0.60kg (1.32lb)

• Drop ceiling mount 0.54kg (1.19lb)

• Drop ceiling cover 0.12kg (0.26lb)

• Surface mount cover 0.13kg (0.29lb)

• Power adapter, including mains cable: 0.43kg (0.95lb)

Connectors & buttons

Mounting

The AXIS 215 PTZ can be mounted in 2 different ways:

• Surface mounted on a hard ceiling, in which case the unit is fastened directly to the

ceiling material

• Recessed in a drop ceiling, which involves cutting a hole in the ceiling and using

the supplied drop ceiling mount

The front position

The AXIS 215 PTZ can pan (swivel) ±180° from position 0°, i.e. the metal tab to the left of

the connectors, as illustrated above. This position can be thought of as the “front” of the

camera, and is the point to which the camera will return whenever it is (re)started.

!IMPORTANT! - The AXIS 215 PTZ is designed for indoor and outdoor use. To

use the camera outdoors, it must be installed in an approved outdoor housing.

Please see www.axis.com for more information on outdoor housings.

Power connector

(see page 16)

Network connector

(see page 16)

I/O terminal

connector

(see page 16)

Status, Network & Power

Indicator LEDs (see

page 17)

Audio out

Control button

Audio in

Position 0°

Page 6 AXIS 215 PTZ Installation Guide

Surface mounting

If the required cabling is also surface mounted, the cables should enter via the removable

cable inlet on the large plastic dome cover.

1. Use the supplied template to mark

out the positions for the screws that

will fasten the camera to the ceiling.

If required, drill holes for the

supplied mounting plugs.

2. Use the 2 supplied 4.2x38 screws to

fasten the camera to the ceiling.

3. Connect the camera to the network

using a shielded network cable.

4. Optionally connect external input/

output devices, e.g. alarm devices.

See page 16 for information on the

terminal connector pins.

5. Optionally connect an active speaker

and/or external microphone.

6. Connect the supplied indoor power

adapter to the power connector.

7. Using the supplied screwdriver,

attach the large dome cover, using

the 2 M4x10 resitorx screws.

Notes:

• When power is applied, check that the

indicator LEDs indicate the correct

conditions. See the table on page 17 for

further details.

• The dome cover can be fitted with the

clear or the smoked plastic glass. See

Replacing the dome glass, on page 9.

Cable inlet

4.2x38mm

screw

M4x10 resitorx

screw

AXIS 215 PTZ Installation Guide Page 7

ENGLISH

Drop ceiling mounting

1. If possible, remove the ceiling tile in which the drop ceiling mount is to be fitted.

2. Use the supplied template to mark the position for the hole in the ceiling tile. Remove the

protective paper, fix to ceiling tile and cut around the template.

Note: The combined weight of the camera, ceiling mount and cover is 1.26 kg (2.78 lb). Check

that the ceiling material is strong enough to support this weight. The thickness of the

ceiling should be 20-60mm (0.79”-2.36”).

3. Tilt and insert the outer ceiling bracket through the hole, and then pull it into place. The

bracket should be positioned so that the 3 vertical tabs point downwards in the hole.

4. Pull all of the required cables

(network, power, etc) down through

the hole, ready for connection.

5. Using the 4 supplied M4x10 screws,

mount the camera on the inner

ceiling bracket, as illustrated here.

Ceiling tile

Outer ceiling bracket Hole diameter 168-175mm

(6.6-6.9”)

Page 8 AXIS 215 PTZ Installation Guide

6. Adjust the length of the

supplied safety wire and attach

it to both the inner bracket and

the hard ceiling above the drop

ceiling.

7. Connect the camera to the

network using a shielded

network cable.

8. Optionally connect external

input/output devices, e.g.

alarm devices. See page 16 for

information on the terminal

connector pins.

9. Optionally connect an active

speaker and/or external

microphone.

10. Connect the supplied indoor

power supply to the power

connector on the camera.

11. Lift and turn the inner bracket

(with camera) so that the

screws on the outer bracket

enter the screw slots on the

inner bracket. Make sure that the screws go all the way to the back of the slots.

12. Gently tighten the screws so that the ceiling tile is held between the inner and outer

brackets. Check that none of the cabling is trapped by the brackets.

Note: When power is applied, check that the indicator LEDs indicate the correct conditions.

See the table on page 17 for further details.

Safety wire

Align slots

with screws M4x4 screw

AXIS 215 PTZ Installation Guide Page 9

ENGLISH

13. Using the supplied screwdriver, attach the smaller dome cover, using the 2 M4x10

resitorx screws.

Replacing the dome glass

The dome cover can be fitted with the clear or

the smoked plastic glass. To switch covers, use a

torx T6 screwdriver to remove the 4 fastening

screws on the inside of the dome, as shown here.

You are advised to take care when handling the

plastic glass, to avoid scratching it. The wearing

of cotton gloves is recommended.

M4x10 resitorx

screw

Page 10 AXIS 215 PTZ Installation Guide

Assign an IP address

Most networks today have a DHCP server that automatically assigns IP addresses to

connected devices. If your network does not have a DHCP server the AXIS 215 PTZ will use

192.168.0.90 as the default IP address.

If you would like to assign a static IP address the recommended method in Windows is either

AXIS IP Utility or AXIS Camera Management. Depending on the number of cameras you

wish to install, use the method that best suits your purpose.

Both of these free applications are available on the Axis Network Video Product CD supplied

with this product, or they can be downloaded from www.axis.com/techsup

Notes:

• If assigning the IP address fails, check that there is no firewall blocking the operation.

• For other methods of assigning or discovering the IP address of the AXIS 215 PTZ, e.g. in other

operating systems, see page 15.

Method Recommended for Operating system

AXIS IP Utility

See page 11

Single camera

Small installations

Windows

AXIS Camera Management

See page 12

Multiple cameras

Large installations

Installation on a different subnet

Windows 2000

Windows XP Pro

Windows 2003 Server

Autres manuels pour 215 PTZ

Table des matières

Langues :

Autres manuels Axis Caméra de sécurité

Axis

Axis P3365-V Manuel utilisateur

Axis

Axis Q6155-E Manuel utilisateur

Axis

Axis Q1604 E Manuel utilisateur

Axis

Axis M1137 Manuel utilisateur

Axis

Axis Q6052 Manuel utilisateur

Axis

Axis Q60-E Series Manuel utilisateur

Axis

Axis P3265-LVE Manuel utilisateur

Axis

Axis NETWORK CAMERA 2100 Manuel utilisateur

Axis

Axis P47-PLVE Series Manuel utilisateur

Axis

Axis P3715-PLVE Manuel utilisateur

Axis

Axis P39 Series Manuel utilisateur

Axis

Axis P32 Series Manuel utilisateur

Axis

Axis P1364 Manuel utilisateur

Axis

Axis Q1765-LE PT Manuel utilisateur

Axis

Axis P14 Series Manuel utilisateur

Axis

Axis P3344-VE Manuel utilisateur

Axis

Axis P13 Series Manuel utilisateur

Axis

Axis Q1942-E Manuel utilisateur

Axis

Axis M1103 Manuel utilisateur

Axis

Axis Q1615 Mk III Manuel utilisateur

Axis

Axis P32 Series Manuel utilisateur

Axis

Axis P3346 Manuel utilisateur

Axis

Axis Q6315-LE Manuel utilisateur

Axis

Axis M1065-L Manuel utilisateur

Manuels Caméra de sécurité populaires d'autres marques

Okina USA

Okina USA SIR36-870VF650LP Manuel utilisateur

Divio

Divio NDR155PA Manuel utilisateur

Canon

Canon VB-C500D Manuel utilisateur

Easy Access

Easy Access EasyGuard Manuel utilisateur

Vivotek

Vivotek FD9389-EHV-v2 Manuel utilisateur

TUYA

TUYA COSMO W2 Manuel utilisateur

Eusso

Eusso UNC7500-IR Guide de configuration

urmet domus

urmet domus 1096/204 Manuel utilisateur

VC VC20 series Manuel utilisateur

ieGeek

ieGeek DD201 Manuel utilisateur

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Manuel utilisateur

Vicon

Vicon V662-D-1 Mode d'emploi

Grundig

Grundig GCH-K0274P Manuel utilisateur

Lorex

Lorex VANTAGE LBC7032 Manuel utilisateur

4xem

4xem WPT Manuel utilisateur

Samsung

Samsung SCV-3082 Manuel utilisateur

Vitek

Vitek VTC-C544 Manuel utilisateur

Lumens

Lumens VC-A50PNW Manuel utilisateur