AWID XR-3600 Instructions de montage
XR-3600 Reader Installation Sheet Version 1.1 Page 1 of 2
Installation Sheet (Wiegand Interface)
XR-3600 UHF Card Reader
hese instructions are for AWID’s Model XR-3600 mullion-mount reader, using compatible UHF credentials
from AWID.
Parts List
(a) 1 Installation Sheet XR-3600
(b) 1 Model XR-3600 Reader
(c) 2 #6-32
X
1” self-tapping screw (for sheet metal, wood, plastic, screw anchor, etc.)
Preparation
Reader Location: Select the reader’s mounting location. he XR-3600 Reader may be screwed to a door
mullion or window mullion, or to a wall or other surface. On a metal surface, read range is reduced about 20%.
he XR-3600 Reader may be exposed directly to rain or snow.
DC Power Supply: DC power for this reader is usually supplied from the +DC and Ground terminals of the
Wiegand reader port on the system’s panel. If this is not possible, use an independent power supply. Power
may be shared with other readers if the supply has sufficient current capacity. he power supply should be
nominal +12 volts DC (as low as +5 volts is OK); 1 ampere capacity; linear-rated; regulated DC output.
Cable to Controller and Power Supply: 4 conductors from reader to the system (2 wires for DC power, and 2
wires for Wiegand data). 22 gauge. Overall 100% shield for both power and data. 500 feet maximum length.
If the DC power supply is independent from the panel’s reader port, the reader’s Black wire must be
connected to both the DC power supply’s Negative terminal and the panel’s Ground terminal.
If the DC power supply is close to the reader, run two 22 gauge cables – 2 wires for DC power, and 3 wires
for Wiegand data. Both cables must be overall-shielded and earth-grounded.
Conduit: If cables are pulled through metal conduit, the conduit should be earth-grounded (like the cables).
(continued)
XR-3600 Reader Installation Sheet Version 1.1 Page 2 of 2
Procedure
1. Connector – Cut off the white 10-pin connector from the end of the reader’s cable. Discard the connector.
2. Wire Connections – Connect the reader’s wires to the cable(s) for power and data.
a. First, connect lack to the panel port’s Ground terminal, and, if separate, to the power supply Negative.
b. Connect green to the Data-0 terminal. Connect white to the Data-1 terminal.
c. Connect the gray drain wire to the shield of the connecting cable.
If power and data are in separate cables, connect all three drain/shields together near the reader.
d. At the end of the cable(s) near the panel (and near the power supply, if separate), connect the shield to a
verified earth-ground.
e. Last, connect red to the DC Positive terminal.
3. Reader Mounting – Feed the reader’s cable through the cable opening in the mullion or wall. Mark and
drill lead-holes in the surface where the reader will be mounted. Fasten the reader to the mullion or wall,
with screws through the holes at the ends of the reader. Use supplied screws if suitable.
4. Screw-Hole Plugs – After you have tested the reader, press the plugs over the screw heads in the reader.
5. Reader est – When power is applied to the XR-3600, the LED initializes to steady-red for standby, and
the beeper sounds. With every presentation of an AWID UHF card to the reader, the LED changes color
momentarily, and the beeper sounds briefly. Read range with a compatible AWID card is up to 6 inches.
6. System est – Wire the reader to the system’s controller. Program the code for the AWID UHF card or
keytag into the host system, with full priority, all doors groups, and all time zones. Present the card or
keytag to the reader. Observe door unlock or gate opening, indicating “Access Granted” by the system.
Technical Support ● Call 408-825-1100, option 1. E-mail S[email protected].
Table des matières
Autres manuels AWID Lecteur de cartes
AWID
AWID SENTINEL-PROX MR-1824 Instructions de montage
AWID
AWID LR-3000 Manuel utilisateur
AWID
AWID Sentinel-Prox DC-1023 Instructions de montage
AWID
AWID LR-3200 Instructions de montage
AWID
AWID SENTINEL-PROX DK-1025 Manuel utilisateur
AWID
AWID Sentinel-Prox MR-1824HiLo Instructions de montage
AWID
AWID SR-2400 Instructions de montage
AWID
AWID SR-2400 Instructions de montage
AWID
AWID SENTINEL-PROX SC-2300 Manuel utilisateur
AWID
AWID MM-6800 Instructions de montage
AWID
AWID MPR-3014WF-QB Manuel utilisateur
AWID
AWID SP-6820 Instructions de montage
AWID
AWID Sentinel-Sense ADB-512 Manuel utilisateur
AWID
AWID MPR-5005 Manuel utilisateur
AWID
AWID XK-3640 Instructions de montage
AWID
AWID SENTINEL-PROX LR-911 Manuel utilisateur
AWID
AWID uAxcess XJ-1023 Manuel utilisateur
AWID
AWID SENTINEL-PROX LR-911 Manuel utilisateur
AWID
AWID LR-2200 Manuel utilisateur
AWID
AWID KP-6840 Instructions de montage
