Avtech KPC131 Manuel utilisateur

203Z

KPC131_135_V1.0

USER MANUAL

Regular Camera Series

The product image may differ from the actual product.

Please read the instructions thoroughly before using the product.

The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user

to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of

sufficient magnitude to constitute a risk of electric shock to persons.

To reduce the risk of electric shock, do not expose this apparatus to rain or moisture.

Only operate this apparatus from the type of power source indicated on the label.

The company shall not be liable for any damages arising out of any improper use, even if we have been

advised of the possibility of such damages.

This exclamation point within an equilateral triangle is intended to alert the user to the presence of

important operating and maintenance (servicing) instructions in the literature accompanying the

appliance.

ROHS Announcement

All lead-free products offered by the company comply with the requirements of the European law on

the Restriction of Hazardous Substances (RoHS) directive, which means our manufacture processes

and products are strictly “lead-free” and without the hazardous substances cited in the directive.

The crossed-out wheeled bin mark symbolizes that within the European Union the product must be

collected seperately at the product end-of-life. This applies to your product and any peripherals

marked with this symbol. Do not dispose of these products as unsorted municipal waste.

CE Mark

comply with the radio interference. This apparatus is manufactured to

The company does not warrant that this manual will be uninterrupted or error-free. We reserve the

right to revise or remove any content in this manual at any time.

OVERVIEW

Equipped with a 1/3” Color CCD image sensor, this regular camera possesses

satisfactory minimum illumination to provide clear and sharp images and has a

microphone built-in to consolidate the quality of your surveillance system.

FEATURES

1. High quality picture

2. Satisfactory minimum illumination of 0.3 Lux/F2.0

3. Audio function supported

4. Auto Electronic Shutter built-in

5. Signal-to-noise ration of 48dB

SPECIFICATIONS*

Pick up Element 1/3" Color CCD image sensor

Number of Pixel 512(H) x 492(V) <NTSC> / 512(H) x 582(V) <PAL>

Resolution Standard

Min. Illumination 0.5 Lux / F2.0

S/N Ratio More than 48dB (AGC off)

Electronic Shutter 1/60 (1/50) to 1/100,000 sec.

Lens Mount C/CS mount changeable

IRIS Mode D.D./ V.D./ AES

AGC Auto

White Balance ATW

Video Output 1.0 Vp-p composite, 75Ω

Microphone YES

Power Source (±10%) DC12V AC24V / DC12V AC230V

Current Consumption (±10%) 80mA --

Power Consumption (±10%) -- 1.8W max.

Dimensions (mm)** 108(L) x 62(W) x 50(H)

* The specifications are subject to change without notice.

** Dimensional Tolerance: ± 5mm

PACKAGE CONTENT

‧ Camera x 1

‧ User manual x 1

‧ CS-C conversion ring, iris connector, wrench x 1

MAJOR OPERATING CONTROL AND FUNCTIONS

Back Panel of MODEL 1

VIDEO AUDIO

V.D. D.D.

AES AI

LEVEL

L H

AU TO IRI S

12V DC

Back Panel of MODEL 2

AC24V / DC12V AC230V

VIDEO AUDIO

V.D. D.D.

AES AI

LEVEL

AC 24V

DC 12V

VIDEO AUDIO

V.D. D.D.

AES AI

LEVEL

AC 230V 22

1. Flange Back Adjusting Ring

It is suitable for CS-mount lens. When using C-mount lens, please use the CS-C conversion ring.

2. Back Focal Lock Hexagonal Bolt

The camera is set at the standard back focal position. Fine-tuning is inevitable according to the lens types.

Adjust the lens back-focus by turning the focusing knob.

3. Auto Iris Lens Connector

Supplies power and controls signals to an Auto Iris Lens.

Connect to the auto iris lens cable with the supplied iris connector (4-pin male connector).

4. DC Drive Level adjustment V.R.

When using Direct Drive Lens, you can adjust the DC Drive Level for the bright of video output.

5. Power LED Indicator

The Power LED Indicator indicates normal status during operation.

6. Power Input Terminal !

 For connecting to DC12V regulated power supply.

 For connecting to the regulated AC230V power supply.

 For connecting to DC12V / AC24V regulated power supply.

* : For connecting with the ground (earth) of power supply cable.

7. Video Output Connector (VIDEO OUT)

For connecting to CCTV monitor video input with coaxial cable.

8. Function Select

 AES (Automatic Electronic Shutter) / AI (Auto Iris Lens) selectable:

AES – When using a manual iris lens or fixed iris lens, set this switch to AES.

AI – When using an auto iris lens, set this switch to AI.

9. V.D. / D.D. selectable

When using Auto Iris Lens, select Video Drive or Direct Drive depend on the type of lens you used.

10. Audio Output Connector (AUDIO OUT)

Connect to the AUDIO IN connector of the recording device.

INSTALLATION

***The following installation is better accomplished by qualified service personnel or system installer.***

1. Mount a lens onto the camera (By turning it clockwise).

It is suitable for CS-mount lens.

But if the lens you chose is C-mount, please use the supplied CS-C conversion ring to connect the C-mount

lens and the camera.

auto iris lens, please refer to N

1 for installation instructions. If the lens you chose is

2. Switch the lens selection depending on the lens you used.

* Manual iris lens or fixed lens:

AES: When using manual iris lens or fixed iris lens, set switch to AES.

* Auto iris lens:

AI: When using auto iris lens, set switch to AI.

V.D. / D.D.: When using Auto Iris Lens, select VD or DD depend on the type of lens you used.

3. Connect the camera VIDEO output and the monitor video input with a 75Ω coaxial cable.

4. Connect the camera AUDIO output and the monitor audio input with a coaxial cable.

5. Connect the POWER terminal of the camera to a right power supply.

6. Adjust the focus or flange-back (Please refer to N

2 for adjustment instructions).

NOTE 1: Auto Iris Lens Connector Installation

Cut the iris control cable at the edge of the lens connector to remove the existing lens connector.

Remove the outer cable cover of the supplied connector as shown in the diagram.

The pin assignment of the auto iris lens connector is as follows:

Auto Iris Lens V.D. D.D.

Pin 1: Power source Damp －

Pin 2: Video signal Damp ‧

Pin 3: Not used Driver ‧

Pin 4: Ground, Shield Driver －

Solder the lens cable to the pins of the supplied connector

Flange Back Adjusting Ring

Back focal lock hexa

onal bolt

NOTE 2: Focus or Flange-Back Ring Adjustment

1. Mount the lens

by turning it clockwise on the lens mount of the camera.

2. Loosen the screws on the flange-back adjusting ring.

3. Turn the flange-back adjusting ring to the desired position.

4. Tighten the screws on the flange-back adjusting ring.

PRECAUTIONS

 Do not install the camera in an environment where the humidity or temperature is high

 Do not install the camera under the unstable lighting condition

 Do not expose the camera to rain or moisture

 Do not keep the camera face to strong light directly

 Do not touch the front glass of the camera

 Do not use other than specified power source

 Do not disassemble the camera

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Avtech Caméra de sécurité

Avtech

Avtech AVN363 Manuel utilisateur

Avtech

Avtech AVC153 Manuel utilisateur

Avtech

Avtech DGC1104XFT Manuel utilisateur

Avtech

Avtech AVN420 Manuel utilisateur

Avtech

Avtech AVT1104TP Manuel utilisateur

Avtech

Avtech AVM328 Manuel utilisateur

Avtech

Avtech IC-AVM2421 Manuel utilisateur

Avtech

Avtech AVT1206TP Manuel utilisateur

Avtech

Avtech AVT532 Manuel utilisateur

Avtech

Avtech 22X series Manuel utilisateur

Avtech

Avtech AVI321 Manuel utilisateur

Avtech

Avtech AVM332 Manuel utilisateur

Avtech

Avtech AVN80X Manuel utilisateur

Avtech

Avtech dg205b Manuel utilisateur

Avtech

Avtech AVC484A Manuel utilisateur

Avtech

Avtech avn212 Manuel utilisateur

Avtech

Avtech MEGAPIXEL WIRELESS NETWORK CAMERA SERIES Manuel utilisateur

Avtech

Avtech AVN211 Manuel utilisateur

Avtech

Avtech AVT583 Manuel utilisateur

Avtech

Avtech Ezum DGC1304-10 Manuel utilisateur

Avtech

Avtech DGC1125AXT Manuel utilisateur

Avtech

Avtech AVM357A Manuel utilisateur

Avtech

Avtech 960H Manuel utilisateur

Avtech

Avtech IM-132E Manuel utilisateur

Manuels Caméra de sécurité populaires d'autres marques

Okina USA

Okina USA SIR36-870VF650LP Manuel utilisateur

Divio

Divio NDR155PA Manuel utilisateur

Canon

Canon VB-C500D Manuel utilisateur

Easy Access

Easy Access EasyGuard Manuel utilisateur

Vivotek

Vivotek FD9389-EHV-v2 Manuel utilisateur

TUYA

TUYA COSMO W2 Manuel utilisateur

Eusso

Eusso UNC7500-IR Guide de configuration

urmet domus

urmet domus 1096/204 Manuel utilisateur

VC VC20 series Manuel utilisateur

Axis

Axis Q1614 Manuel utilisateur

ieGeek

ieGeek DD201 Manuel utilisateur

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Manuel utilisateur

Vicon

Vicon V662-D-1 Mode d'emploi

Grundig

Grundig GCH-K0274P Manuel utilisateur

Lorex

Lorex VANTAGE LBC7032 Manuel utilisateur

4xem

4xem WPT Manuel utilisateur

Samsung

Samsung SCV-3082 Manuel utilisateur

Vitek

Vitek VTC-C544 Manuel utilisateur