AV-CAD AV-5000 LED Manuel utilisateur

Easy L o a der

AV-5000 LED,

AV-5000 GSM

(For LED keypads)

Integrated Alarm Control panel &

Communicator 8 zones

Installation and Operation

Express Manual

Version 1.00

Edition I

This product is subject to continuous enhancements and therefore

specifications may be changed or altered without prior notice

Item: 4765E_LED (A3BKE)

Rev 04: 27-Feb-2022

Table of contents

Introduction series AV-5000 for LED keypad..................................................... 3

Tips to first time installer.................................................................................... 3

Revision changes .............................................................................................. 3

Keypad AV-701, AV-702 short description......................................................... 4

2. Wiring Devices Alarm Panel................................................................................6

2.1 AV-5000 Zone Wiring .................................................................................. 6

2.2 Tamper per zone & EOL wiring ................................................................... 6

2.3 EOL Zone Wiring......................................................................................... 7

2.4 Keypad Wiring ............................................................................................. 7

2.5 PIR as Eye Spy II wiring .............................................................................. 9

2.6 Siren Wiring................................................................................................. 9

2.7 Back-Up Battery .......................................................................................... 10

2.8 DC Power Supply 5014TER ........................................................................ 10

3. Telephone Line (Central Station no available) ....................................................11

3.1 Telephone Line............................................................................................ 11

3.2 AV-5000 with GisMo module ....................................................................... 11

3.3 SVM – Synthesized Voice Module SVM-40, SVM-42................................... 12

3.4 Telephone and SMS address ...................................................................... 12

4. System Codes.....................................................................................................12

4.1 Description of main codes (8 codes)............................................................ 12

4.2 Enter user programming & Set New User Code .......................................... 13

4.3 SMS and dialer number entry by user.......................................................... 13

4.4 Installer Programming mode & Code change (code 33) .............................. 13

4.6 Auto Arming & Passive Auto Arming ........................................................... 14

5. LED Keypad & Hold down Functions ..................................................................14

5.1 Hold-Down Functions .................................................................................. 14

5.2 Group Bypass (home mode)........................................................................ 16

5.4 LED Dual Keys Hold-Down Functions ......................................................... 18

5.5 Keypad Functions at location 200................................................................ 18

5.6 Keypad Main Operations ............................................................................. 19

5.7 Keypad Sounder.......................................................................................... 21

5.8 LED Indicators............................................................................................. 21

7. Programming Sheet Version 1.00 LED ...............................................................23

8. Powering Up & Programming Examples .............................................................26

8.1 Before Powering Up .................................................................................... 26

8.2 Reset System to Default Programming........................................................ 27

8.3 Installer (Engineer) Programming Examples ............................................... 27

9. GisMo GSM module add on................................................................................29

9.1 GSM for series 5000 SMS format ................................................................ 29

9.2 Programming GSM and Dial features .......................................................... 30

10.1 Wiring Diagram.......................................................................................... 31

AV-5009 LED GSM ready Wiring Diagram ........................................................ 31

Introduction series AV-5000 for LED keypad

The series 5000 alarm panels for LED keypads are simple, easy to customize and

programming.

Series 5000 models

This is an express manual for series 5000 alarm panels for LED keypad supplied as

technical reference; with each alarm panel we provide a short format manual.

Model AV5009_GRND is GSM only SMS messaging and dial, not supports PSTN dial.

Alarm panel AV-5009 supports 8 double zones, replace older models AV-3008, AV-

4008, AV-4009.

For GSM versions refer to the GSM section.

Panels with Gismo (GSM on board) are compatible with LED keypads: AV-701, AV-702.

Not compatible with LCD keypads.

Tips to first time installer

If you are a first time installer, do not hook up any remote sensors at first. The most common

confusion comes about when the alarm will refuse to arm, because one or few zones are

“troubled”. Complete the power supply, siren, keypad and strobe wiring, and for the moment

connect ALL the zone terminals to –V. This will simulate a system with all zones looped out

through closed switches. The alarm is supplied already programmed with an “average” list of

settings (default) and can be used straight away, a few of the program locations may have to be

changed to suit the actual sensors and output devices used.

 Read this manual carefully, it looks complicated, but all the information is there

 Do not power up with battery! Use the DC power for start and testing. Default programming code is 1994, user

01 code is 1234 (01, 02...08)

 To start with: Hook up the keypad, connect all zones to –V or apply resistors for 8 zone mode, power-up by

applying DC only

 In case the keypad displays ‘8’ and keys not respond verify the minus (-V) wire and other keypad connection

 Fast test: Verify “Dial LED" Self Test at Initialization (STI) - Blinks for the first 50 seconds after power on,

confirms panel is operative, from keypad wait to six beeps to confirm communication OK.

 Arming is possible if all zones are close, unless delayed zone/s. To test don't enable EOL zone/s.

 Arm and disarm the system, when the Status LED light steady (not blinking), enter your master code; 1234

 Try the hold-down functions. Hold each key for approximately 2 seconds

 Set the system time by holding-down key ‘0’ then ‘1’, set time in 24H format, blinking ‘Set Time’ stop

 The default programming is set for siren alarm device that requires 12V to alarm (Bell Mode)

 Make sure you are using the Earth terminal for Grounding; it is not a -V (minus) terminal

 Typing six erroneous codes will lock the keypad keys for 30 seconds

 In program mode press 200 then 00 to display control panel type & software version

Revision changes

Date Version Contains

05-DEC-2021 1.00 First published

Keypad AV-701, AV-702 short description

F i g u r e 1 : A V - 7 0 1 & A V - 7 0 2 L E D k e y p a d d e s c r i p t i o n

Common Terms in this Manual

 ‘SHUNT‘ and ‘BYPASS’ are interchangeable terms

 Program Mode - Enables features programming, alarm is disabled

 Use Mode – System is disarmed and not in alarm or program mode

 AV-701 and/or AV-702 are identical in operation

 Standard Keypad functions are accessed by pressing keys (short press). The 1 to 0

keys used for Arming/Disarming (ON/OFF), Zone Shunt (Bypass) and other

programming functions.

 A short beep confirms each key press.

A short press on keypad key accesses the following special functions:

Chime Instant Arming, by pressing key ‘5’ (requires programming).

Shunt Zone Bypass, by pressing key ‘0', followed by entering the Zone number/s

Group Bypass explained in the keypad section.

For full details refer to the keypad section in this manual and the keypad manual.

The AV-5000 LED alarm panel board carries a specific identification label (refer to wiring

diagram) that indicates the software version and panel type.

Display control panel model and software

Enter Programming Press 200 and then 00, keypad display control panel type and

software version.

First set shows the control model, then software version, then the software date.

Siren Shunt

Display Status

Delay

Delete Chime

Test Program Reset

Shunt

Telephone

ARMED STATUS SHUNT FIRE

ZONE

DISPLAY

EASYLOADER AV-701

AV-GAD

Warranty and technical support

If end user or a person on his behalf change product, wrong wiring or programming our product he do so on his

own risk, product warranty is void is such case.

Av-Gad Systems Ltd can't technical support such customers, contact local technical or installer. Warranty terms

are published separately.

About electronic fuse Av-Gad use

Series 5000 power and siren/s outputs are protected by automatic reset able (PTC) electronic fuses, read

below overview to get familiar with this fuse type.

Electronic Fuse Overview

The Electronic Fuse device included as a series element in electric circuit. In response to an

over current it protects the circuit by going from a low-resistance to a high-resistance state that

reduces the current to a level that’s safe for the circuit elements. The change in resistance is the result of a rapid

increase in the temperature of the device. Like traditional fuses, Electronic Fuse devices interrupt the flow of

dangerously high current. However, unlike traditional fuses, they automatically reset after the fault cleared and

power to the circuit removed. Because they are solid-state, Electronic Fuses are also better able to withstand

mechanical shock and vibration, and provide reliable protection in a wide variety of applications. In case of over

current, carefully touch the fuse body (yellow round disc), hot body means the Electronic Fuse in protection

mode, disconnect the load and wait 2-3 minutes until the fuse body get cooler.

2. Wiring Devices Alarm Panel

2.1 AV-5000 Zone Wiring

The AV-5000 provides two ways of zone wiring: None EOL (EOL = end of line) resistor

loop (factory default), EOL resistor loop only for zone 4 and 8. The EOL loop protects

the zone lines against tampering.

F i g u r e 2 . 1 : N o n e E O L m o d e zo n e w i r i n g

2.2 Tamper per zone & EOL wiring

Tamper alarm per zone is not available with AV-5009 in eight (8) zones mode. The -V is

common for EOL resistors.

Av-Gad 3000

Series panel

-V Z1

Eye-Spy II

PIR

2.2K 4.7K

Notice wires to -V

Colors

2.2K

Colors

4.7K

Red

Yellow

Purple

Red

F i g u r e 2 . 2 : E O L m o d e z o n e w i r i n g

2.3 EOL Zone Wiring

The AV-5009 factory default is 8 zones none EOL zones. If EOL mode is required move

jumpers as shown in figure 2.2. The zones are referred to –V.

If zone 4 or 8 selected as EOL type add in series with the 2.2.K (zone 4) or 4.7K (zone

8) resistor and the sensor contacts (relay. Refer to figure 2.3.

2.4 Keypad Wiring

Up to three AV-701 or AV-702 Keypads can be connected to AV-5009. When few

keypads are connected, wire each one directly to the panel, not from one keypad to the

other. Refer to drawing in next page.

When using few keypads connect them in parallel. Each keypad has four terminal wires:

 (+) Power, connect to + Aux. Power  System Data, connect to OR

 (–) Power, connect to – Aux. Power  System Strobe, connect to YE

F i g u r e 2 . 3 : W i r i n g m o r e t h e n o n e k e y p a d

Wire length for each Keypad should not exceed 100 meters (when using 0.5 mm2

wires).

For longer then 100 meters (320 feet) keypad wiring, contact manufacturer's consultant.

For AV-701/702TP (keypad with tamper) run five (5) wires. Connect the TMP terminal to

a 24H or Tamper zone.

Power at Keypad should be a minimum of 11.5 Volts.

IMPORTANT! Never run Keypad wires alongside telephone wires, high voltage

wires, or transmitting antennae. Wire the keypad wires separately and not in same

cable with other devices (telephone, PIR etc.)

For proper connection, refer to wiring diagrams at the end of the manual.

F i g u r e 2 . 4 : W i r i n g L E D k e y p a d t o c o n t r o l p a n e l

Wiring terminal of keypad type AV-702 (in above figure) and for AV-701 keypad are

identical.

2.5 Motion detector PIR as Eye Spy II wiring

The PIR (Passive Infra Red) detector is a motion sensor that upon detection opens the

relay contacts, this activated the alarm panel. In higher security installation it's

recommended using EOL resistors that protect the wires from being tampered.

Figure 2.5: W iring PIR or similar detector to control panel

2.6 Siren Wiring

The siren output is protected by Electronic Fuse. Av-Gad Bella sirens are recommended

for high efficiency and low current consumption.

The 5000 series is compatible with 12V DC sirens at maximum 0.3A. Higher current

damage the siren driver.

Connect the Tamper switch to 24H zone (requires programming).

F i g u r e 2 . 6 : W i r i n g s i r e n s t o c o n t r o l p a n e l

Warning, siren/s current should not exceed 0.3 Ampere

Bell mode is factory default; in Bell mode install a 12V DC siren, which contains sound

driver or electronic modules that powered by 12V DC.

Bell Mode converts Siren outputs into 13.6V DC outputs (no sound is issued).

Bell mode is applicable for driving self-powered sirens or bells, or combined sirens and

strobes.

Siren configuration programming address

Address Feature Explanation

068 Siren test/beep upon arming Sounds a short beep to indicate arming

072 Bell mode Send 12V DC to drive the siren

073 Self contained siren Send 12V at idle, drop to zero V at alarm

092 Siren 3 beeps when disarm by

key

Sounds 3 short beeps to indicate

disarming

070, 071 Siren duration times Configures the siren times

2.7 Back-Up Battery

Make sure to connect the Battery in the correct polarity! Wrong polarity may

cause explosion.

The system's Red wire is the positive pole (+) and the Black wire is the negative pole (-).

 The battery will provide power back up in case of AC power failure.

 Connect back-up battery to ensure proper operation of the system.

 Recommended battery: 7 Amperes per Hour (AH), 12V (sealed lead acid) type.

 A 7.2 AH battery backs up the control panel and a single keypad for approximately 6-8

hours, depends on total system current consumption.

 Series 5000 panels accommodates a battery of up to 12V–9 AH maximum.

 An Electronic Fuse rated at 2.5A protects the battery.

 Add an external power supply for installation with over three LED keypad and/or if over

ten high current sensors alarm system. Refer to Av-Gad AV-21, AV-40 power supply and

charger.

The 4AH–12V battery fits in the ABS box, but the door is too tight, why? Note the

following:

1. Notice two small bulges on the ABS box door (designed for supporting and hold

the battery) may displace the battery; place the battery between the bulge and not

on it

2. Make sure that the battery is not laying on the income wiring

2.8 DC Power Supply 5014TER

Each alarm panel requires DC 14V, factory item 5014TER. Check DC or solar voltage

level before connecting the DC power source or solar.

When using DC sources make sure to connect the power in the correct polarity! When

solar panel removed connects other power source like 5014TER. Don't connect higher

voltage then 14V DC power source to prevent internal heat up and total lost.

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels AV-CAD Système de sécurité

AV-CAD

AV-CAD EasyLoader AV-2016D Manuel utilisateur

Manuels Système de sécurité populaires d'autres marques

Inner Range

Inner Range Concept 2000 Manuel utilisateur

Climax

Climax Mobile Lite R32 Instructions de montage

CADDX

CADDX NX-6 Manuel utilisateur

FBII

FBII XL-31 Series Manuel utilisateur

Johnson Controls

Johnson Controls PENN Connected PC10 Manuel utilisateur

Aeotec

Aeotec Siren Gen5 Manuel utilisateur

Blaupunkt

Blaupunkt SA 2700 Manuel utilisateur

IDEAL

IDEAL Accenta Manuel du propriétaire

AJAX

AJAX DoubleButton Manuel utilisateur

Swann

Swann SW-P-MC2 Manuel utilisateur

Ecolink

Ecolink Siren+Chime Manuel utilisateur

Digital Monitoring Products

Digital Monitoring Products XR150 Manuel utilisateur

EDM

EDM Solution 6+6 Wireless-AE Manuel utilisateur

Highway Safety Group

Highway Safety Group EA401 Manuel utilisateur

Siren

Siren LED GSM Manuel utilisateur

Detection Systems

Detection Systems 7090i Instructions de montage

Se-Kure Controls

Se-Kure Controls MicroMini SK-4841 Manuel utilisateur

Siemens

Siemens FDM273 Manuel utilisateur