Auxdio AM8300 Manuel utilisateur
* * Central Audio System
1
Instruction to Product
AM8300 is the partition extended power amplifier used for the multi-room network music
system. Every set of AM8300 is able to provided 4 additional partitions for the user, so as to meet
the needs of the user for multiple partitions. One AM8328 host is able to connect 16 AM8300
extending boxes by the “hand-in-hand” or star connection mode. Any set of AM8300 has its own
address ID, which the user may change according to his/her own needs.
Description of Appearance
1. Description of Front Panel
1) Power switch.
2) Input voltage selecting switch with two voltage levels at 115V and 230V, which the user may
select according to the actual condition of the power supply.
Note: The voltage selecting switch must be turned to the corresponding level; otherwise, the
machine may be burned!
2
1
* * Central Audio System
2
2. Description of Rear Panel
1) RS485 interface: Used to connect BM828R control panel.
2) RJ45 interface: Used to connect the case with AM8328 host (Or previous extending box).
3) RJ45 interface: Use to cascade the next extending box.
4) Partition audio output wiring terminal: Used to connect the partition output wiring terminal of
the extending box; totally, there are 4 stereo wiring terminals, which are used to connect four
partitions.
5) Power socket.
6) Partition numbering: [9 + (Set value) × 4]] ~ [8 + (Set value+1) × 4]
Partition numbering knob: By default, the rotary disk points to “0”; in such case, the
extending box partition numbers as displayed on AM8328 shall be “9, 10, 11 and 12”; if it
points to “1”, the extending box partition numbers as displayed on the host shall be “13, 14,
15 and 16”, and the rest can be done in the same manner. The user may make the
corresponding setting according to the requirements.
Note: Whenever you want to add several sets of AM8300 to AM8328, make sure to set the
address ID of AM8300 and prevent the repeated ID! After setting ID, it is required to reboot
AM8300.
6
7
5
3
2
1
4
* * Central Audio System
3
Description of Connection
1. Connecting AM8300 to host, “hand-in-hand” connection
mode
* * Central Audio System
4
2. Connecting AM8300 to AM8328 host, star connection
mode
If you want to achieve the star connection mode, it is required to provide one exchanger.
In case of the insufficient length of the network cable, you may make the network cable by
yourself in accordance with the connection method as shown below.
Note: Every twisted-pair wire connected to each other shall be <=100m in length.
Exchanger
Spring clip
Back to you
1st pin
RJ45 interface
As connection method, the colors from
left to right are:
Green & white, green, orange & white,
blue;
Blue & white, orange, brown & white,
brown
Corresponding one to one between two
ends
* * Central Audio System
5
3. Connecting AM8300 to BM828R control panel
Remark: In two-channel
input connection, there may
be 15 panel controllers on
any channel connected by
“hand-in-hand” mode
Infrared remote controller
* * Central Audio System
6
Packing List
No.
Product
Quantity
1
AM8300 host
1 set
2
Power line
1 piece
3
Operation instruction
1 copy
4
Quality certificate and warranty card
1 copy
Performance Specification
Item
Indicator
Number of partition
4 partitions
Audio
frequency
indicator
Rated output power
Stereo, 8×30W/8Ω
Frequency response
20Hz-20kHz (±0.5dB)
Total harmonic distortion
<0.3% (f=1kHz, 1/3 of rated output power)
Signal to noise ratio
> 81dB
Room controller interface
Using RJ45 network cable
Power amplifier output protection
Any partition has output short-circuit, overloading and direct
current protection
Power supply
AC115V or 230V/50-60Hz
Consumed power
< 350W
Power protection
AC220V/F6A
Dimension of outer packing (mm)
(L×W×H) 340×340×160
Dimension (mm)
(L×W×H) 230×285×65
Gross weight
3.2kg
Net weight
2.8kg
Table des matières
Autres manuels Auxdio Amplificateur
