Auvi WIP20S Manuel utilisateur
www.auvivoip.comwww.auvivoip.com
®®
WIP20S
Instruction Manual
Skype™ Telephone Adapter
Designed
for
Skype™
Table of Contents
www.auvivoip.comwww.auvivoip.com
Section 1: Notices
Regulatory Compliance 01
Trademarks 02
Section 2: Introduction
WIP20 Diagram 03
Package Contents 03
System Requirements 03
Section 3: Skype™ Software
Installing Skype™ 04
Creating a Skype™ Account 05
Adding a Skype™ Contact 06
SkypeIn 08
SkypeOut 08
Section 4: Hardware Connection
Connecting the WIP20 09
Section 5: Auvi Software Installation
Installing the Auvi Interface 11
Section 6: Operations
Using the WIP20 with Skype™ 14
Basic Operations Guide 15
Section 7: Troubleshooting 16
Section 8: Limited Warranty 17
Notices Section 1
0101
Regulatory Compliance Notice
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses, and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there is
no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
• Reorient or relocate the receiving antenna;
• Increase the separation between the equipment and receiver;
• Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected;
• Consult the dealer or an experienced radio/TV
technician for help.
Modifications
The FCC requires the users to be notified that any changes or modifications made to this
device that are not expressly approved by the party responsible for compliance may void the
user’s authority to operate this device.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions:
(1) This device may not cause harmful interference;
(2) This device must accept any interference received, including interference that may cause
undesired operation.
0202
Trademarks
© 2006 Auvi Electronics N.A., LLC. All rights reserved.
Auvi Electronics N.A. “Auvi” shall not be liable for any errors contained herein or for any
damages arising out of or related to this document or the information contained herein, even if
Auvi has been advised of the possibility of such damages. This document is intended for
informational and instructional purposes only. Auvi reserves the right to make changes in the
specifications and other information contained in this document without prior notification. Auvi
disclaims any obligation to update the information contained herein.
Auvi Technologies, Auvi Electronics N.A., Auvi logo and Vision Beyond Sound
are trademarks or registered trademarks of Auvi Technologies, LLC in the United States and/or
other countries. Windows is a trademark or registered trademark of Microsoft Corporation in
the United States and/or other countries. Skype and the Skype logo are trademarks or
registered trademarks of Skype Technologies, S.A. in the United States and/or other countries.
All other product names may be trademarks of the companies with which they are associated.
Warning: To reduce risk of electric shock, do not directly or indirectly (through a phone)
connect the device to a PSTN wall outlet.
Technical Support
For more information regarding the WIP20, please visit our online technical support site at
http://www.auvivoip.com or contact us directly at:
Auvi Electronics N.A.
5988 Mid Rivers Mall Drive
Saint Charles, MO 63304
Telephone: 636-447-4005
Section 1
Introduction Section 2
0303
Diagram
Package Contents
The contents are specifically designed to be used only with the WIP20.
System Requirements:
• IBM PC compatible with minimum 400MHz processor
• 128MB RAM
• 5MB available hard disk space
• Available microphone and audio out jack
• CD-ROM drive
• Windows® XP only
• Analog traditional or cordless telephone
• Broadband or dial-up Internet connection
Power in
Audio in
Mic in
Audio out
Connect telephone cord
Software
Installation CD
3.5mm-to-3.5mm
line-in cords (2)
Quick start guide
WIP20
AC adapter
Skype™ Software Section 3
0404
The first step to using the WIP20 is to install Skype™ on the computer. This section describes
how to download and install Skype™, create a Skype™ account and add contacts.
Installing Skype™ Software
If you already have the latest version of Skype™ on your computer, go to the next section. If
you don’t have the latest version, please follow the steps below.
1. Access the web and go to:
http://www.skype.com.
2. Double-click the download button for
Windows®.
3. Once downloaded, double-click the
setup icon to start the installation.
4. Choose a language.
SkypeSetup
5. If you agree to the License Agreement,
click in the circle next to “I accept the
agreement”, then click NEXT.
6. Save Skype™ on your hard drive.
Creating a Skype™ Account
0505
7. In the next window, set up additional
tasks, if needed, then click NEXT.
8. Click FINISH in the last window to
complete the installation.
1. In the “New Users Create a Skype
Account” tab, enter the required
information. Click NEXT.
2. “Your Skype Personal Profile”
Enter the information in the approiate text
boxes. Click UPDATE.
Section 3
0606
Adding a Skype™ contact
1. Once logged-in to your account, go to the
main Skype™ account window.
2. From the menu at the top of the window,
select Tools, and then Add a Contact.
3. Enter the name of another Skype™ user
in the appropriate text box, then click
NEXT.
4. Make the appropriate selections, then
click OK.
Section 3
0707
5. The contact will be added when
authorized. Click FINISH.
The contact has been added. To view the
contact list, select the Contacts tab from
the main Skype™ window.
Section 3
SkypeIn
SkypeOut
Section 3
0808
SkypeIn is a paid service provided by Skype™. This service allows your Skype™ account to
be called from any traditional landline phone or mobile phone. When you are signed up with
SkypeIn and your phone rings, simply pick up the handset and answer like you would normally
do with a traditional home phone.
To learn more about SkypeIn, please visit http://www.skype.com.
SkypeOut is a paid service provided by Skype™. It is a low cost way to make calls from Skype
to family and friends who still use traditional landlines or mobile phone. Also, SkypeOut offers
great international rates to stay connected with anyone worldwide, 24/7. Before using
SkypeOut, please go to http://www.skype.com to purchase SkypeOut credits.
Once your SkypeOut account is activated and it has a positive credit balance, you will be able
to use the telephone connected to the WIP20 to make domestic and international calls.
To make a SkypeOut call, you must enter the number in the following way (even for local calls):
"country code" + "number" + “#”. You can also use "00" or "011" before the country code.
Example (U.S. Phone Number):
Dial: 1-555-555-5555#
Example (Hong Kong Phone Number):
Dial: 852-1234-5678#
Autres manuels pour WIP20S
3
Table des matières
