AUTOTERM COMFORT CONTROL Manuel utilisateur

v10.2020

Manufacturer: AUTOTERM LLC

Paleju 72, Marupe, Latvia, LV-2167

Warranty Department warranty@autoterm.com

Technical Support service@autoterm.com

www.autoterm.com

COMFORT CONTROL

User’s manual

 
 
CONTENTS 
CONTENTS..................................................................................................................................2 
INTRODUCTION..........................................................................................................................3 
SAFETY INSTRUCTIONS ..............................................................................................................3 
LIABILITY.....................................................................................................................................4 
GENERAL INFORMATION....................................................................................................5 
1. DISPLAY........................................................................................................................5 
2. ROTARY KNOB .............................................................................................................6 
3. BACK BUTTON .............................................................................................................6 
4. QUICK BUTTON............................................................................................................6 
5. LED INDICATORS..........................................................................................................6 
MOUNTING AND CONNECTION..........................................................................................7 
OPERATION AND SETTINGS................................................................................................8 
1. MAIN MENU................................................................................................................8 
2. TIMERS ........................................................................................................................8 
3. HEATING....................................................................................................................10 
4. VENTILATION.............................................................................................................12 
SETTINGS...........................................................................................................................13 
1. TIME/DATE ................................................................................................................13 
2. DISPLAY......................................................................................................................13 
3. HEATER (for air heaters)............................................................................................13 
4. PRE-HEATER (for liquid heaters)................................................................................14 
5. LED.............................................................................................................................15 
6. RESET.........................................................................................................................15 
FAULTS AND ERRORS........................................................................................................16 
 

INTRODUCTION

Dear Customer!

Thank You for choosing control panel AUTOTERM Comfort Control! We are doing everything

to make this product meet Your requirements, so its quality satisfies every customer.

Comfort Control is designed to be intuitive and comfortable to use, to ensure the best

experience when it comes to controlling Your climate.

AUTOTERM Comfort Control is compatible with all AUTOTERM AIR and FLOW heaters.

Some older versions of PLANAR heaters may not support some of the functions.

In case of questions about compatibility with older products please contact Your

local dealer or AUTOTERM Service center.

In case of any problems, we strongly recommend to contact certified service centres. Contact

information and location of certified service centres can be found at our website

www.autoterm.com.

Please read carefully this manual before operating the AUTOTERM heaters.

This manual contains needful information in order to use this product correctly.

Disregard of these instructions can void the warranty of the product, lead to

damage of product and/or property and be a risk to health.

If the heater is handled and/or installed improperly, there is a possibility of a fire

hazard and damage of property because fuel and electrical components are being

used. That is why all safety precautions, operation and installation instructions

must be observed.

For other languages of this manual, please see www.autoterm.com/manuals.

SAFETY INSTRUCTIONS

Risk to health and/or damage of product

-The heater may only be used for the purposes specified in its respective operation

manual.

-DO NOT use the heater in closed and/or poorly ventilated places (e.g. garage, workshop,

etc.)

-Do not step on the heater or put any objects on it and in it.

-Do not put any body parts or items in to any of the air inlets or outlets of the heater.

-For air heaters. Do not allow hot air to be blown directly at people, animals or heat

sensitive objects.

-To avoid burns, do not touch the exhaust lines and the heater while it is operating.

Risk of fire and explosion

-The heater is not designed for installation and use on any type of ADR transportation

vehicle.

-When refuelling heater must be shutdown. Note: shutdown process can take up to 10

minutes.

-The vehicle where the heater is installed must be equipped with a fire extinguisher.

-Do not cover the heater with clothing, pieces of fabric and so on, and do not place such

objects in front of the air intake pipe or inlet and output of the heated air.

-Do not use or install the heater in places, where flammable vapours or gases or large

amounts of dust may form and accumulate.

-Do not use or install the heater in places, where flammable and/or explosive items or

substances are stored.

-Avoid contact of any flammable objects with the heater’s exhaust pipe.

Risk of damage due electrical nature

-Do not connect/disconnect any wiring of the heater while it is connected to the power

supply or operating.

-Do not connect the heater to the power circuit of the vessel, when the engine is

operating and there is no battery.

-The heater can be switched on again 15-20 seconds after disabling indications on the

control panel, which means that the heater has shut down.

Personnel certified by AUTOTERM is needed

-In case of faults in the operation of the heater, contact specialized repair organizations

authorized by AUTOTERM.

LIABILITY

Manufacturer is not liable for any damage as a result of installation and repairs by

uncertified personnel and/or use of third-party parts and accessories without the

approval of manufacturer.

In case of any problems, we strongly recommend to contact certified service centres. Contact

information and location of certified service centres can be found at our website

www.autoterm.com.

1. GENERAL INFORMATION

1. DISPLAY

3. BACK BUTTON

5. LED INDICATORS

2. ROTARY KNOB

4. QUICK BUTTON

1.1. DISPLAY

•While in sleep mode:

odisplay is inactive;

oscreensaver shows:

─temperature;

─current time and date;

─set operation mode, if active.

Control panel goes in to sleep mode after the time of inactivity set

in display settings.

Sleep mode is cancelled by pressing any button or turning the knob either direction.

•While active display shows:

ocurrent time;

opower supply voltage;

otemperature;

oset operation mode, if active;

oactive timers.

To access the main screen control panel has to be woken from sleep

mode.

For air heaters temperature displayed depends on the temperature sensor

selected.

For liquid heaters temperature of the coolant is displayed.

Description of each symbol and screen layouts can be found in their respective

sections of the manual.

When an operation mode is active, respective symbol is displayed on the main screen (under

the current time) and it works as a quick menu. By rotating the knob three options can be

accessed:

•Active operation mode

settings

•Shut off the heater

•Access the main menu

Confirm selection by pressing the knob.

1.2. ROTARY KNOB

The rotary knob is the main button for navigation through the interface.

•When control panel is active pressing the knob enters the main menu. After that

pressing the knob confirms selected item or setting.

•Turning right selects next item or increases value of selected setting.

•Turning left selects previous item or decreases value of selected setting.

1.3. BACK BUTTON

Back button is used to return to the previous screen by pressing it once.

1.4. QUICK BUTTON

Quick button can be used to start or stop the heater without entering the main menu or

quickly enabling or disabling timers.

•While heater is off, pressing the button once opens the “Heating” menu.

•While the heater is off, long-pressing the button for 2 seconds starts the heater with

previous settings (Display message: “Starting…”).

•While the heater is operating, long-pressing the button for 2 seconds switches off the

heater (Display message: “Switching off…”).

•While the heater is operating, pressing the button once opens the settings of the

active operation mode.

•In the menu “Timers” pressing the button once enables/disables the selected timer

(for this action timer has to be set beforehand).

1.5. LED INDICATORS

LED indicators are used to indicate the operating mode or status of the heater:

•RED –heater is working in heating mode;

•BLUE –heater is working in ventilation mode;

•GREEN –heater is switching off (purge mode);

•RED (blinking combined with display message) –an error has occurred.

•LIGHT GREEN (one blink every 5 seconds) –a timer has been enabled.

2. MOUNTING AND CONNECTION

Control panel can be mounted using screws or double-sided adhesive tape.

For mounting with screws, gently remove the back panel using a thin flat screwdriver, by

prying it from the middle of one of the sides. Then screw the back panel to your desired

surface.

For mounting with double-sided adhesive tape, before installation degrease the back of the

control panel and the desired surface.

When connected to the power supply control panel turns on automatically.

When turned on LED indicators light up, while showing AUTOTERM logos on the display.

Connection process takes approx. up to 20 seconds. If connection is established display shows

main screen. If connection fails message “No connection!”is displayed.

After disconnecting the control panel form the power supply time and date must

be reset. Rest of the settings, such as set timers, remain saved.

3. OPERATION AND SETTINGS

3.1. MAIN MENU

Main menu can be accessed from main screen by pressing the rotary knob once. Navigate

through the menu by turning the knob. To enter the selected menu, press the knob once.

TIMERS

Is used to set and enable/disable up to 3 timers.

HEATING

Is used to set different heating modes, depending on the

connected heater.

VENTILATION

Is used to set ventilation mode (except for AIR 8D and liquid

heaters).

SETTINGS

Is used to change general settings of the control panel and

heater.

3.2. TIMERS

In “Timers” menu up to 3 timers can be set to start the heater at specific

time in desired mode for desired duration.

To set timers select the “Timers” menu from the main menu by pressing

the knob once.

Choose one of three timers by rotating the knob and pressing the knob

once to confirm the selected timer.

Quick button ( ) can be used to enable/disable previously set timers.

After selecting a timer, choose to enable, edit or delete the timer by

rotating the knob and pressing the knob once to confirm one of the

options.

Editing the timer

Set the time of day for heater to start:

•Set hours and confirm;

•Set minutes and confirm.

Set working duration of the heater.

Duration can be set from 30min to 720min* with increasing step of

5min.

*up to 120min for liquid heaters

Set days for heater to start, where:

•ED (Every Day) –heater starts every day of the

week;

•EW (Every Workday) –heater starts every day

from Monday to Friday;

•SEL (Select specific day) –heater starts only on

specified days, where:

1 –Monday

3 –Wednesday

5 –Friday

7 –Sunday

2 –Tuesday

4 –Thursday

6 –Saturday

Set the operation mode for air heaters:

•Heating mode

•Heat + Ventilation mode

•Ventilation mode

Set the operation mode for liquid heaters:

•Pre-heating mode

•ECO mode (only for FLOW 14D)

When all the parameters are set message “Saved” is shown on the display

and the timer is enabled automatically. Enabled timers can be seen on the

bottom part of the main screen. LED indicators will blink light green once

every 5sec when timer is enabled.

3.3. HEATING

In “Heating” menu different operation modes for heating can be set,

depending on the connceted heater.

To set heater modes select the “Heating” menu from the main menu by

pressing the knob once and then select one of the heating modes:

Temperature can be set in a range from 0°C up to 30°C, with step of 1°C.

Work time can be set in a range from 30 min up to infinity, with step of:

•5min up to 2h;

•20min up to 12h;

•after 12h next step is ∞.

Heating modes for air heaters:

TEMPERATURE MODE

–

Heater will maintain set temperature by reducing the heating

power, without shutting off the combustion process.

POWER MODE

–

Heater will operate constantly at set power level.

HEAT + VENTILATION

–

Heater will operate till the temperature is reached 1°C above

the set temperature, shut off the combustion process and

start to ventilate till the temperature drops 5°C below the set

temperature. When temperature drops, heating starts again.

THERMOSTAT MODE

–

Heater will operate till the specified temperature is reached

then shuts off the combustion process and ventilation. After

the temperature drops by specified degrees heating will start

again.

Setting Temperature mode

Select “Temperature mode” from the menu.

Set temperature and confirm.

Set work time and confirm.

When mode is active, respective symbol is shown on the main

screen

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels AUTOTERM Panneau de contrôle

AUTOTERM

AUTOTERM PU-5 Manuel utilisateur

AUTOTERM

AUTOTERM PU-27 Manuel utilisateur

AUTOTERM

AUTOTERM CP-27 Manuel utilisateur

AUTOTERM

AUTOTERM PU-27 Manuel utilisateur

AUTOTERM

AUTOTERM PU-28 Manuel utilisateur

Manuels Panneau de contrôle populaires d'autres marques

RDZ

RDZ PC-HRX Manuel utilisateur

STG-BEIKIRCH

STG-BEIKIRCH MZ3 Manuel technique

Efka

Efka Variocontrol V810 Manuel utilisateur

Cebora

Cebora 208-10 Manuel utilisateur

AMX

AMX AutoPatch CP-15 Manuel utilisateur

Satel

Satel CA-6 KLED-S Manuel utilisateur

Evolution

Evolution IQ plus 800 Manuel utilisateur

Fagor

Fagor 8040 TCO CNC Manuel utilisateur

Trane

Trane ComfortLink II XL950 Control Manuel utilisateur

AKO

AKO PROCool AKO-17635-2 Manuel utilisateur

ABB

ABB 6136/30M-101 Manuel utilisateur

Telikou

Telikou BK-603 Belt Pack Manuel utilisateur

Mapei

Mapei Mapeheat Thermo Touch Manuel utilisateur

Bosch

Bosch D9412GV4 Manuel utilisateur

Mitsubishi Heavy Industries

Mitsubishi Heavy Industries SC-SL4-AE2/1 Manuel utilisateur

Sminn

Sminn BOX L VF1L EI Manuel utilisateur

Balboa

Balboa TP600 Manuel utilisateur

Nice

Nice HSCU1 Caractéristiques techniques