Autoleader D0904 Manuel utilisateur

D0904 OWNER’S MANUAL

一、 The dashboard consists of the Monitor(1), the Data Processing Unit(DPU)(2), and

several different types of Sensors. There are two types of Power Cords. Power Cord A(3) can

be plugged into the car's cigarette lighter. Power Cord B(4) can be integrated directly into

the car's circuit. The DPU receives and processes data transmissions from the Sensors, and

sends the processed data to the Monitor via Bluetooth. The Sensors consists of the Oil

Pressure Sensor(5), the Water Temp Sensor and Oil Temp Sensor(6), Boost Gauge Sensor(7)

and its Accessories(8), Exhaust Gas Temp Sensor(9) and its Accessories(10), Sensor Wires(11)

and the Monitor Stand(12).

二、 The Monitor has two sockets, one is on the left edge and the other is on the right edge,

only one socket can be connected to a cord at a time. The sockets are MiniUSB sockets.

(IMPORTANT: This socket is incompatible with normal MiniUSB cords, specialised cords

must be used. Usage of incompatible cords may damage the device.)

三、 The Monitor has four buttons, positioned on the left and right side, two on each side.

Upper-left button reads "Menu/OK", it is used to bring up the Settings Menu, execute the

"confirm" action and other functions. Lower-left button reads "Exit/Cancel", it is used to

Exit the Settings Menu and execute the "cancel" action. Upper and Lower-right buttons are

“↑”、“↓” buttons respectively. They are used to scroll through options and altering the

options when they are selected.

四、 The light sensor is positioned on the top middle of the Monitor. The backlight of the

screen will change in response to the brightness of the environment, there are a total of 4

brightness levels. Two symmetrical rows of LED lights are positioned at the front of tilted

edges on the Monitor, they will turn on from bottom up as the RPM increases. The colour of

the four pairs lights are "green", "green", "yellow", "red".

五、 Wiring the Sensor and DPU

The DPU has 11 sockets, as shown below. Sockets 1 to 11 are connected to the devices with

corresponding numbers:

1. spare socket

2. spare socket

3. power

4. Boost sensor

5. Oil Pressure sensor

6. Air Fuel Ratio sensor

7. Oil Temp sensor

8. Water Temp sensor

9. Exhaust Gas Temp sensor

10. RPM (green wire) and Speed meter (red wire)

11. spare socket

六、Before connecting to power, start the engine of the car. After connecting to power, the

Monitor will search for the DPU automatically and establish connection. Before the connection is

established, the Monitor should look like this:

七、When the connection between the Monitor and the DPU is established, and the dashboard is

receiving the sensor data successfully, it will switch to the normal display, as shown below:

1. RPM

2. Speed

3. Oil Pressure

4. Air Fuel Ratio

5. Turbo

6. Coolant Temp

7. Voltage

8. Time

9. Multi-purpose display section. Displays the date by default. The display can be changed by

using the “↑” and “↓” button.

八、By pressing the “↑” and “↓” button the multi-purpose display section can display different

data:

Press the “↓” button to display to the RPM

Press the “↓” button again to display the Oil Pressure

Press the “↓” button again to display the Oil Temp

Press the “↓” button again to display the Exhaust Gas Temp

The multi-purpose display will memorize which data has been selected to be displayed, and will

display that data the next time when it is connected to power.

九、 Press and hold the "Menu/OK" button to access the Settings Menu. See the figure below.

Now press the “↑” and “↓” button to select the setting that you want to adjust, press the

"Menu/OK" button to begin adjusting the selected setting. Press the "Exit/Cancel" button to exit

Settings Menu, and return to the normal display. The adjustable settings are:

1-SET DATE

2-SET TIME

3-SET UNIT (select to change the measurement unit for pressure)

4-SET LED (select to turn the LED on and off)

5-SET ALARM (select to adjust the speed limit alarm)

6-SPEED CAL (select to calibrate the speed)

Each setting will be explained below:

1. Press and hold the "Menu/OK" button to access the Settings Menu, then press "↓", the

Monitor shows "1-SET DATE", press the "Menu/OK" button again to enter the date settings, as

shown below:

The bottom row displays the current "date-month-year". A dot is located at the bottom right

corner of the "date" section. Now press the “↑” and “↓” buttons to adjust the date. When you

finish adjusting the date, press "Menu/OK" to move dot to the bottom right corner of the

"months" section. Now press the “↑” and “↓” buttons to adjust the month. When you finish

adjusting the month, press "Menu/OK" to move dot to the bottom right corner of the "years"

section. Now press the “↑” and “↓” buttons to adjust the year. When you finish adjusting the

year, press "Menu/OK" to confirm the action and return to the Settings Menu. If you make a

mistake in the previous date selection, you can press the "Exit/Cancel" button to move the dot

backwards, until you exit the setting.

2. Press the "↓" button again to display "2-SET TIME",

press the "Menu/OK" button again to enter the time settings, as shown below:

Adjust the "hour-minute-seconds" by moving the bottom right dot and using the “↑” and “↓”

buttons. When you finish adjusting the time, press "Menu/OK" to confirm the action and return

to the Settings Menu.

3. Press the "↓" button again to display "3-SET UNIT",

press the "Menu/OK" button again to enter the unit settings, as shown below:

The Monitor displays the current pressure unit by default(PSI), press the “↑” and “↓” buttons

to switch between "PSI" and "BAR". Press the "Menu/OK" button to save the change, or press

the "Exit/Cancel" button to cancel the action.

4. Press the "↓" button again to display "4-SET LED",

press the "Menu/OK" button again to enter the LED settings, as shown below:

The Monitor displays the current LED status. Press the “↑” and “↓” buttons to switch between

"ON" and "OFF". (When the LED is selected "ON", the four pairs of LED lights on the front of the

dashboard will light up as the RPM increases.)

A. When LED is selected "ON", press the "Menu/OK" button to set the RPM value for each pair of

lights. See the figure below:

Manuels Moniteur populaires d'autres marques

Linear Acoustic

Linear Acoustic LQ-1000 Manuel utilisateur

AOC

AOC I2579V Manuel utilisateur

Gateway

Gateway FPD1520 Manuel utilisateur

Furuno

Furuno Mu 120c Manuel utilisateur

Asus

Asus VB171D - 17" LCD Monitor Manuel utilisateur

Dell

Dell S2230MX Instructions d'utilisation

Philips

Philips 107C64 Manuel utilisateur

Dell

Dell S2409WFP Manuel utilisateur

EverFocus

EverFocus EN-7517E Manuel utilisateur

Panasonic

Panasonic TH152UX1 - 152" PLASMA TV Manuel utilisateur

Dell

Dell Precision 7680 Mode d’emploi

LG 50PM1M - - 50" Plasma Panel Manuel utilisateur

Bosch

Bosch DDU 9 Manuel utilisateur

Acer

Acer A231HL Manuel utilisateur

Philips

Philips 86BDL4152T Manuel utilisateur

NEC

NEC AccuSync LCD5V Manuel utilisateur

Emay

Emay SleepO2 Manuel utilisateur

IBM

IBM 6360 Instructions d'installation