Autoglide MAGRO-35A Manuel utilisateur
INSTRUCTIONS MAGRO-35A
Page 1
SWING GATE OPENER
INSTRUCTIONS MAGRO-35A
Page 2
SWING GATE OPENER
INDEX
1. Features
2. Technical Specifications
3. Mechanical Installation
4. Manual Release
5. Wiring
6. LED Diagram
7. Wiring For Optional Accessories
8. Remote Control Setting
9. Battery Wiring Instructions
10.
Flashing Light Installation
INSTRUCTIONS MAGRO-35A
Page 3
SWING GATE OPENER
1.
Features
1. Manufacturer has patent for manual release mechanism. Use this feature in case of
Power failure, during installation or maintenance
2. Easy Self-learning feature (Page 9)
3. Commercial power & solar energy power source can be connected at the same time
4. Over current immediate stop function (A0~ A1/B0~B1)
5. Adjustable time of fast speed & slow speed (A2~A5/B2~B5)
6. Adjustment of force during fast speed & slow speed (A6~A7/B6~B7)
7. Auto close function with adjustable closing time delay
8. Optional electric lock connection facility
9. Single or dual swing
10. Use Max up to 50 sets of remote controllers
11. Dc 24v backup battery (optional)
12. Flashing Light AC 220V/110V & DC 24V (optional)
13. Optional Device: DC 24V gate lock, photocell, extensional receiver box
2.
Technical Specifications
Electrical
Operating voltage DC 24V
Electronic Controller Microcontroller Based
Safety Detection Over current detection
Safety Barrier Infrared Beam Sensor(Optional)
IP Rating IP66
INSTRUCTIONS MAGRO-35A
Page 4
SWING GATE OPENER
Mechanical
Swing Type Magro-35A
Max. piston stroke 450mm
Max.length of motor 1255 mm
Max.leaf’s weight 350kg/leaf
Suitable Leaf’s Length 2 to 3.5 meter/leaf
Frame Housing stainless steel/aluminum alloy
Driving Method Screw driven piston type
Opening degree 0 to 110 degree
90 degree rotation time 8 to 12 seconds
Temperature -25 degree C to + 55 degree C
3. Mechanical Installation
INSTRUCTIONS MAGRO-35A
Page 5
SWING GATE OPENER
Diagram Installation
Opener Dimension
INSTRUCTIONS MAGRO-35A
Page 6
SWING GATE OPENER
Bracket Dimension
Installation Precautions
1. Please make sure there is some angle between the position of the gate bracket and the
post bracket and these two brackets should not be in parallel position.
2. Make sure the position extend have at least 5 mm allowance when the gate in
Opened / Closed position.
3. There are two small holes in the swing arm motor,please make sure this side face down
when do installation for water proof purpose.
INSTRUCTIONS MAGRO-35A
Page 7
SWING GATE OPENER
4. Manual Release
In case of power failure, the operator can be dis engage from the gate, follow the
directions below to release and rotate the operator to enable the manual release function.
1. Using Allen Key (Special Key) to unlock the manual release function.
2. Toward te “open” direction to rotate 90 degree or ¼ turn.
3. Now the manual release function is enabled when maintaining or no power.
4. After maintaining, rotate 90 degree back to the locked position, then use special
key to lock the moving part.
www.autoglideglobal.com
INSTRUCTIONS MAGRO-35A
Page 8
SWING GATE OPENER
Control Box Setting
1. Wiring
1
.Power Switch.
2
.Accessories and command device’s terminals.
3.
Indicator.
4.
Function Adjustment Button.
5.
Motor A (With Electronic Lock).
6.
Motor B
7.
Output DC 24V (Unstable Voltage).
8.
OV “-“ output
9.
Output DC 15V stable voltage
(load current can’t be over 500 MA)
10.
DC 24V Electric Lock.
11.
DC 24V Flashing Light
* * photocell (see page 1 6)..
12.
Back up Battery (12 v 9 ah x 2 in series)
13.
Connector
for adaptor.
14.
Solar Panel
15.
Switch
(AC 220V & 110V). 16.
Power Supply
(AC220/110V).
17.
Earthed.
18.
AC Flashing Light
LED DIAGRAM
Power on LED 5 will blink. LED 1 Motor A Open LED. LED 2 Motor A close LED.
LED 3 Motor B open LED. LED 4 Motor B close LED. LED 5 Power LED.
LED 6 Received signall for remote control LED. LED 7 Pushbutton LED
INSTRUCTIONS MAGRO-35A
Page 9
SWING GATE OPENER
2. Wiring for Optional Accessories
Item +15V OP/CS 1/2PN GND STOP CLOSE OPEN GND Remarks
Description
Stable
voltage
output
Dual
Open
Single
Open
"-" &
"Concentration
line"
Stop
Close
Normally
opening
signal
"-" &
"Concentration
line"
Extensional
Receiver Box
(single gate)
Extensional
Receiver Box
(dual gate)
Keypad
(single open )
Keypad
(dual open )
Push button (two
buttons)
Push button
(one button)
close gate only
single open
dual open
Photocell
(sender)
Photocell
(receiver)
INSTRUCTIONS MAGRO-35A
Page 10
SWING GATE OPENER
How to Connect the Motors
Motor A:
Connect the two wires from the motor to the “ Motor A” terminals marked on the control
board. If you find the motor is operating in the wrong direction, reverse the motor wires on
the circuit board.
Motor B:
Repeat the above steps except connect to Motor B.
3. Remote Control Setting
3.1 Activating the Remote Control
Press and hold the “F” button for approximately one seconds (With out pressing the button
on the remote control) or until the indicator displays “FF” and keeps flashing, then release
the “F” button.
Press any button on the remote control, if the display stops flashing “FF”, it means the
remote control is programmed to the PCB and is valid (50 remote controls can be set at
most)
*Verify the remote control is operating by pressing a button on the remote. When press
any button on the remote control, the LED 6(on the PCB) will be on.
3.2 Erasing the code
Press and hold “F” button for approximately one seconds (with out
pressing the button on the remote control) or until the indicator displays “FF” and keeps
flashing, then release the “F” button.
Press and hold the “Enter” button until the display stops flashing “FF” this indicates all
remotes have been erased and are invalid.
**pedestrian opening push “p” button to perform single swing opening
(Note: only valid for double swing systems)
Table des matières
Autres manuels Autoglide ouvre-porte
Autoglide
Autoglide CASA-50P Manuel utilisateur
Autoglide
Autoglide CASA-120-O Manuel utilisateur
Autoglide
Autoglide CABRI-30P Manuel utilisateur
Autoglide
Autoglide CABRI-20P Manuel utilisateur
Autoglide
Autoglide FERO 600-M Manuel utilisateur
Autoglide
Autoglide VELOCE 80A Manuel utilisateur
Autoglide
Autoglide Magro-500 J Manuel utilisateur
