Autoadapt Carolift 40 Manuel utilisateur

1. PRESENTATION

Carolift 40 is a wheelchair hoist with a lift capacity of 40 kg, designed for installation in vehicles.

The hoist has an articulated arm that folds towards both sides. This feature enables the wheelchair to



narrow rear door openings or behind wide bumpers.

The rotating movement is made manually



use, be easily removed from its base and placed elsewhere.



EMC Direktive 95/54/EC (Electronic disturbances)

Machine Direktiv 2006/42/EC (Risk for injuries, lift capacity, m.m.)

ECE regulations R-17 (Crash test)







procedure has ended and when not in use.

2. SAFETY REGULATIONS

The contents of these instructions must be read and understood before the product is

taken into use. Keep the instructions easily accessible for further reference.

If Carolift is altered, rebuilt or used for other purposes than intended, Autoadapt AB

denies any liability.

Installation and repair of Carolift must, for safety reasons and for warranty conditions,

be made by Autoadapt AB or by a workshop authorized by Autoadapt AB.

Make sure the lift belt is not twisted when retracted on the reel.

3. HOW TO USE CAROLIFT 40

Erecting and folding the hoist

2. To fold the hoist press the catch at the base.

Grab hold of the hoist arm to prevent it from falling





It can also be placed leaning on the loaded wheelchair.

1. To erect the hoist just pull it up until it is locked in an

upright position.

Remove the hoist

1. If the hoist is not needed it can easily be removed by

just lifting it out from its holder on the base.

2.

please refer to ” Erecting and folding the hoist”

above.

Loading the wheelchair

1. Erect the hoist and rotate it outwards. Place the

wheelchair in a suitable position for hoisting it up.

Carolift 40 can pick it up either from the pavement by

the side of the vehicle or from behind.

The illustration shows

a view from above.

This is how the hoist

is moved to provide

the best possible

2. Drive down the lift belt by pressing the toggle switch

on top of the lift arm.

Hook the wheelchair to the lifting device.

Wheelchair

Luggage

compart-

ment

3. Press the toggle switch to lift the wheelchair until it

has reached slightly above the vehicle theshold.

4. Rotate the hoist towards the luggage compartment

and fold the hoist arm inwards to let the wheelchair

pass through the rear door opening.

5. Lower the wheelchair in a suitable position in the

vehicle.



Fold down the hoist on top of the wheelchair according

to the instructions ”Erecting and folding the hoist”

Toggle switch:

Drive down the lift belt

Toggle switch:

Drive up the lift belt

Unloading the wheelchair

1. Erect the hoist and make sure that the lift belt is

hooked to the wheelchair.

Lift up the wheelchair, by pressing the toggle switch,

until it can pass freely over the threshold.

2. Turn the hoist arm outwards and guide the wheel-

chair past the rear door opening to a suitable position

for lowering.

Lower the wheelchair to the ground by pressing the

toggle switch. Unhook it.



to the instructions: ”Erecting and folding the hoist”.

4. MAINTENANCE

4.1 Check-up

If the lift belt is showing signs of tear and wear it

must be replaced by a new.

4.2 Fuse

The hoist has a 10 A fuse that is placed either on

the cable by the plug to the electricity socket or on

the cable just before the connection to the vehicle

battery.

4.3 Lift belt

The lift band shall be replaced every four years.

4.4 Cleaning

Use a vacuum cleaner with a thin nozzle to clean

the hoist base and its cavities.

Use a moist towel to clean from dirt etc.

Symptom Cause Measure

The hoist is not

activeted when

toggle switch is

pressed.

5. TROUBLE SHOOTER

6. TECHNICAL DATA

7. SPARE PARTS

a) The lift belt has been jammed and caused

the fuse to blow.

b) End position is reached.

c) The electricity plug is not connected (applies

for installations via the compartment socket).

d) Vehicle battery is discharged

e) A short circuit has caused the fuse to blow.

Remove the motor and rewind the lift belt

evenly. Replace the fuse.

Activate in reversed direction.

Plug the cable in the socket.

Charge the vehicle battery.

Contact the autorized workshop.

The hoist is working

unusually slow.

Vehicle battery is discharged. Charge the vehicle battery.

In case of an emergency: Try to start

the motor and let the motor run while

unloading the wheelchair.

Lift cacapcity:

Weight (not including the mounting base):

Voltage:

Power consumption at maximum load:

40 kg

11 kg

12 Volt

5 A

The Carolift has a CE-poster where the serial

number is stated.

Please write down this number!

The number is needed when ordering spare parts.

Serial No: ____________________

Art. no: 420157, ed 2

Autres manuels pour Carolift 40

Table des matières

Autres manuels Autoadapt Système de levage

Autoadapt

Autoadapt CAROLIFT 140 Manuel utilisateur

Manuels Système de levage populaires d'autres marques

morse

morse 82H-124 Manuel utilisateur

Braun

Braun NL955 Series Manuel utilisateur

haacon

haacon 1889.10 Manuel utilisateur

Protekt

Protekt AT 252 Manuel utilisateur

R. Beck Maschinenbau

R. Beck Maschinenbau HS 600 Manuel utilisateur

Nova Technology International, LLC

Nova Technology International, LLC NAS Series Manuel utilisateur

Genie

Genie Z-60/34 Manuel utilisateur

Screen Technics

Screen Technics INTERFIT Vertical Up Lift Manuel utilisateur

Mortuary Lift

Mortuary Lift ULTIMATE 1000 Manuel utilisateur

Custom Equipment

Custom Equipment Hy-Brid 3 Series Manuel de programmation

Custom Equipment

Custom Equipment Hy-Brid Lifts 2 Series Manuel de programmation

Hy-Brid Lifts

Hy-Brid Lifts HB-P3.6 Manuel de programmation

BERG

BERG BeNomic EasyLeaf Manuel utilisateur

Powermate

Powermate LiftGate LG-3 Manuel utilisateur

Snorkel

Snorkel TM12 Series Manuel utilisateur

Terberg

Terberg OMNIDEKA Manuel utilisateur

Harmar Mobility

Harmar Mobility AL625 Mode d'emploi

Rotary

Rotary SPO16 Manuel utilisateur