Audiovox SP-6CD Manuel utilisateur

MODEL SP-6CD

6 - DISC CD CHANGER SYSTEM

INSTALLATION MANUAL

SP-6CD

5 Meter DIN cable

(8 pin)

1 pc.

Bracket (R)

1 pc.

Bracket (L)

1 pc.

Self-Tapping Screw

(M5 x 12)

4 pcs.

Hexagonal Bolt

with Washer

M5x8

4 pcs.

Owner's

guide

1 pc.

MAIN UNIT

PACKING LIST

Changer

INSTALLATION PARTS

Installation

Manual

1 pc.

Index seal sheet

1 pc.

CD Magazine

1 pc.

Seals

1 pc.

OTHER ACCESSORY

Note

If the changer is to be installed in a car that is equipped with an on-board drive or navigation computer, do not disconnect

the battery cable. If the cable is disconnected, the computer memory may be lost. Under these conditions, use extra caution

during installation, not to cause a short circuit.

Do not install the unit in the following locations.

Locations exposed to direct sunlight.

Where hot air is discharged from the car heater.

When proper installation is not possible and where a great deal of vibration is generated.

Be sure to use the supplied brackets and screws.

Be careful not to snag any wires when tightening screws and installing the ground wire.

When installing the unit, do not use any screws that are part of the brake or steering system.

This unit cannot be installed in any way except that which is authorized (on its side, on its end, at a 45° angle or suspended).

BEFORE INSTALLING THE UNIT

Transport lock screws

The mechanism in the CD changer is "locked" into place during shipment by the

transport screws. Be sure to remove the screws prior to installation.

After removing the transport lock screws, place the supplied seals over the screw

holes. These seals are used to keep dust out of the unit, which could cause a malfunction.

Installation and Wiring Precautions

To prevent a short-circuit,

Be sure to turn off the ignition and remove the negative (-) battery cable, prior to installation.

Connect power wires last.

Caution 

ID (Identity) Switch for 2nd CD Changer

By using the separately sold Divider unit, an additional compatible CD changer can be installed. When an additional CD changer has been

attached in this fashion, the ID switch is used to indicate the number of each respective changer unit.

When changer is used independently.

* The ID switch is initially set to "1" when shipped.

When changer is used as additional changer unit

* Use a ballpoint pen or similar fine-tipped implement to

change the orientation of the switch. 2nd unit (additional

changer unit)

Never mount the unit near the fuel tank.

Secure the unit in place using four self-tapping screws

(M5 x 12).

SETTING THE ANTI-VIBRATION SPRINGS

This unit can be installed horizontally (suspended), vertically, and at a 45° angle. Once the installation position has been decided, it's

necessary to set the position of the built-in anti-vibration springs inside the unit. Please do this before performing the procedure. Vibration

may cause the disc to skip if the unit is used before properly setting the anti-vibration springs.

At the time of shipping, the built-in anti-vibration springs is set for horizontal installation "H".

There are built-in anti-vibration springs on both the left and right sides.

Set the anti-vibration springs position with a screwdriver before attaching the brackets.

For use when unit is installed horizontally or suspended:

Confirm that the built-in anti-vibration springs is set to position "H".

For use when unit is installed vertically:

The built-in anti-vibration springs should be set to position "V".

For use when unit is installed at a 45° angle:

The built-in anti-vibration springs should be set to position "45°".

Self-tapping screw (M5 x 12)

2Determine the mounting location and drill four mounting holes.

Drill holes 4mm in

diameter.

1Confirm that the built-in anti-vibration springs on both the

left and right sides are set to the horizontal installation

position "H".

Attach bracket (L) and bracket (R) using the hexagonal

bolts (M5 x 8).

PROCEDURE FOR HORIZONTAL INSTALLATION

2Determine the mounting location and drill four mounting holes.

Self-tapping screw

(M5 x 12)

PROCEDURE FOR VERTICAL INSTALLATION

PROCEDURE FOR 45° ANGLE INSTALLATION

Confirm that the built-in anti-vibration springs on both the left and right

sides are set to the vertical installation position "V".

Attach bracket (L) and bracket (R) using the hexagonal bolts (M5 x 8).

Never mount the unit near the fuel tank.

Drill holes 4mm in

diameter.

3Secure the unit in place, using four self-tapping screws (M5 x 12).

Drill holes 4mm in

diameter.

Confirm that the built-in anti-vibration springs on both the left and right

sides are set to the 45° installation position "45°".

Attach bracket (L) and bracket (R) using the hexagonal bolts (M5 x 8).

Determine the mounting location and drill four mounting holes.

Never mount the unit near the fuel tank.

Secure the unit in place using four self-tapping screws (M5 x 12). Self-tapping screw (M5 x 12)

PROCEDURE FOR MOUNTING UNDER REAR DECK

Attach the CD changer using four self-tapping screws

(M5 x 12).

Determine the mounting location and drill four mounting

holes.

4mm

Confirm that the built-in anti-vibration springs on both the left and right

sides are set to the horizontal installation position "H".

Attach bracket (L) and bracket (R) using the hexagonal bolts (M5 x 8).

VEHICLE WIRING

DIN cable (8-pin)

CD changer

Car Stereo with

CD Changer Controls

Mating 8-pin DIN socket on rear of

compatible radio chassis (see Note 1 below).

NOTE: 1. Check with your Audiovox car audio dealer to be sure

your stereo is directly compatible with this CD changer.

2. Wiring instructions for use with FM Modulator/Commander

Systems are included with the CDC-MC1, CDC-MCR2,

P-MC3 and P-MCR4 accessories.

Table des matières

Autres manuels Audiovox Lecteur CD

Audiovox

Audiovox CE201R Manuel utilisateur

Audiovox

Audiovox CDA1361 Manuel utilisateur

Audiovox

Audiovox Prestige SP-11CDP Manuel utilisateur

Audiovox

Audiovox DM8900-00 Manuel utilisateur

Audiovox

Audiovox CDA-475 Manuel utilisateur

Audiovox

Audiovox Portable MP3 CD Player Manuel utilisateur

Audiovox

Audiovox SP-10CD Manuel utilisateur

Audiovox

Audiovox CE149MP Manuel utilisateur

Audiovox

Audiovox CE150MP Manuel utilisateur

Audiovox

Audiovox Rampage ACC-52 Manuel de programmation

Audiovox

Audiovox CE101A - annexe 1 Manuel utilisateur

Audiovox

Audiovox CE270 Manuel utilisateur

Audiovox

Audiovox DM8100_9H_wRW Manuel utilisateur

Audiovox

Audiovox CE1705 Manuel utilisateur

Audiovox

Audiovox DMP8733 Manuel utilisateur

Audiovox

Audiovox CE142AR Manuel utilisateur

Audiovox

Audiovox Rampage ACC-56 Manuel de programmation

Audiovox

Audiovox CE1000X Manuel utilisateur

Audiovox

Audiovox Rampage ACC-31 Manuel utilisateur

Audiovox

Audiovox CE147 Manuel utilisateur

Audiovox

Audiovox CE101C Manuel utilisateur

Audiovox

Audiovox CE144A Manuel utilisateur

Audiovox

Audiovox CE148 Manuel utilisateur

Audiovox

Audiovox CE146B Manuel utilisateur

Manuels Lecteur CD populaires d'autres marques

RCA

RCA RP-7923 Manuel utilisateur

Pioneer

Pioneer DEH-P3550MP XM Manuel utilisateur

Philips

Philips AZ1207 Manuel utilisateur

Philips

Philips CD582 Manuel utilisateur

Philips

Philips AZ 6821 Manuel utilisateur

Lasonic

Lasonic MSU-2020 Manuel utilisateur

THOMSON

THOMSON RCD150 Manuel utilisateur

Denon

Denon DCD-1420 Manuel utilisateur

Panasonic

Panasonic SJ-MR100 Manuel utilisateur

Onkyo

Onkyo DX-7210 Manuel utilisateur

Sony

Sony MZ-R3 Manuel utilisateur

Denon

Denon DVM-4800 Manuel utilisateur

JBL

JBL MR-32 Manuel utilisateur

RCA

RCA RCD152 Manuel utilisateur

Technics

Technics SL-PS770A Manuel utilisateur

Clarion

Clarion compact disc Manuel utilisateur

Sony

Sony MZ-M10 Manuel utilisateur

Philips

Philips Expanium AZ 1538 Manuel utilisateur