Audiovox SRANT-RMSIR Manuel utilisateur

Installation Guide

For the

Roof Mount Satellite Antenna for

SIRIUS/AVX Based Receiver Unit

MODEL SRANT-RMSIR

Contents

1 Introduction......................................................................................................................................2

2 Roof-mount Antenna .......................................................................................................................2

3 General Instructions .........................................................................................................................3

4 Sedans ..............................................................................................................................................4

5 Convertibles.....................................................................................................................................7

6 SUV’s, Minivans and 5 Door Vehicles ...........................................................................................8

7 Pickup Trucks ..................................................................................................................................9

1Introduction

Your new Sirius satellite antenna, approved by

Sirius Satellite Radio, Inc., has been specially

designed to receive signals from Sirius’ three

satellites and Sirius’ network of ground-based

“repeater” transmitters.

Figure 1: Ideal reception pattern

Figure 2: Effect of obstruction on reception pattern

2Roof-Mount Antenna

Figure 3: Low Profile Roof-mount Sirius Antenna

Mechanical data:

Shape “Beveled teardrop”

Color Black

Dimensions 95mm x 70mm x 38mm (approx)

Weight 150 grams (5.25oz) (excl. cables)

Cables 4 meters (13 feet) micro low loss

Connectors 2 x FAKRA / SMB (keyed per specifi-

cation)

Mounting Acrylic foam adhesive pads

Cover Impact resistant glass filled nylon

(paintable)

Electrical data:

Sirius Per specification Sirius

RX000002-010300

Peak Gain (SAT) 6 dBic

3 dB beam width (SAT) 130 degree

4 dB beam width (SAT) 140 degree

Noise figure (SAT) 0.7 dB

Peak Gain (Ter.) 6 dBi

Noise figure (Ter.) 1.1 dB

Environmental data:

Functional operating

temperature -40 to +105 degC

Storage temperature -45 to +120 degC

Humidity Power wash proof

3General Instructions

Satellite antennas are extremely sensitive and

finely specified to facilitate reception of satel-

lite signals under a variety of conditions across

the whole of North America. It is important to

read these “Instructions” carefully to ensure

that the antenna is mounted properly in the best

location in order to provide optimum reception

quality.

3.1 Mounting location

The satellite antenna should be mounted hori-

zontally on a metal surface measuring at least

18 inches by 18 inches. The best reception

quality is achieved at the highest point of the

vehicle (i.e. the roof) but the trunk lid is an al-

ternative location for convertibles and for some

sedans.

It is important that the antenna has a clear

“view” to the satellites and ground-based re-

peaters and should therefore be mounted in an

unobstructed location (i.e. clear of roof racks,

sunroofs, other antennas). Use the table below

as a guide for the required distance (A) between

the antenna placement and a possible obstruc-

tion with a height of (B).

12” 4”

18” 6”

24” 8”

30” 10”

(Glass sunroofs, which open outwards and

cover the rear roof area, should not affect the

location of the antenna module).

3.2 Installation temperature

Installation should be carried out when condi-

tions are at room temperature or above. Firstly,

colder temperatures could affect the curing time

of the antenna module’s adhesive. Secondly,

when mounting the antenna module on a sedan,

it will be easier to work with the rubber mold-

ing around the window.

3.3 Shortening the antenna “tail”

The antenna module is supplied with a 6 inch

tail. For vehicles with flat roofs (SUV’s, Mini-

vans) and for convertibles, it is possible to

shorten the tail by up to 2 inches.

For vehicles with a sloping roof, or if the

module is mounted on the trunk of a sedan,

the tail should not be shortened!

Figure 4: Shortening the antenna tail

As soon as the precise length of the tail has

been determined, the adhesive strip may be cut

to length and applied to the antenna tail.

Figure 5: Applying adhesive tape

3.4 Removing the antenna

The antenna module may be removed, using a

nylon cord (e.g. fishing line) to cut through the

adhesive pad between the antenna module and

the vehicle. Work from the front to the tail in a

side to side cutting motion. Any remaining ad-

hesive may be removed with an appropriate

cleaner.

Figure 6: Removing antenna

4Sedans

Figure 7: Installed antenna

The antenna module should be located along

the centerline of the roof, at least 4 inches from

the rear window.

The antenna cables should be tucked and routed

underneath the rubber molding around the rear

window and into the trunk

1. Clean the general area where the antenna is

to be mounted (using alcohol wipe provided).

2. Identify and mark the precise location of the

antenna module.

3. Peel off protective liner from adhesive pads.

4. Starting with the tail in position, work to-

wards the module while applying pressure of

approximately 12 psi for a minimum of 15 sec-

onds.

Note: Maximum adhesion occurs within 72

hours, during which time car washes and other

contact with the antenna should be avoided.

Fig. 8: Applying the antenna

5. Carefully tuck the cables under the rubber

molding, working from the tail of the antenna,

around the window and into the trunk area.

(A flat tip dental pick or cotter-pin remover is

ideal for lifting the rubber molding and tucking

in the cables.).

Note: Determine whether there is enough space

under the molding to conceal both cables, in

which case they may be run together. If not,

route a single cable around each side of the

window. (If there is no space available, it is

possible to mount the antenna module on the

trunk. Refer to “Convertibles”).

Figure 9: Cables routed together

Figure 10: Cables routed separately

There are two types of window moldings, used

on most vehicles. Both are suitable for conceal-

ing the antenna cable.

Figure 11: Outside rubber molding (most common)

Figure 12: Encapsulated molding (less common)

Note: The window molding will be more flexi-

ble and easier to work with at room temperature

or above. Ensure the molding is clean, and if

necessary apply a small amount of oil to make

the process easier.

Figure 13: Cables routed in standard molding

Figure 14: Lifting up difficult molding for routing each

cable in both directions

6. Route the cable from the lowest point of the

rear window into the trunk area. Take advan-

tage of any existing cable channel or wiring

conduit.

Figure 15: Entering the trunk through cable channel

is important that the coaxial cable is

not damaged or kinked during the instal-

lation procedure. Routing the cable in the

window molding will not affect the sea

ing of the window.

Figure 16: Cables routed directly through the molding

and through the cable channel to the interior

7. If there is no suitable cable channel, the ca-

ble may be routed directly from the window

molding to the right or left corner of the trunk.

Figure 17: Cable routing along the trunk rubber molding

It may be necessary to remove the plastic hous-

ings from the antenna connectors in order to

feed the cables through narrow openings.

Note: Remember to reconnect the correct hous-

ing to its corresponding cable.

Figure 18: Removing connector housings

Most Sirius receivers have two antenna inputs

with the same color-coding as the antenna cable

–white = terrestrial; curry = satellite. However,

some receivers use only one SMB connector, in

which case the plastic housing must be perma-

nently removed and the connector inserted di-

rectly into the receiver.

Figure 19: Connecting the receiver

5Convertibles

Figure 20: Mounted on trunk of sedan

Figure 21: Mounted on trunk of convertible

On convertibles (and some sedans which have

insufficient space under the window molding)

the antenna module should be located on the

centerline of the trunk approximately 6 inches

from the rear window.

1. Follow steps 1 to 4 under “Sedans” to attach

the antenna module to the vehicle.

Figure 22: Routing the cables around the trunk lid rim

2. Route the cable from the rim further under-

neath the lid (use some telephone wire clips) to

the cable channel. Attach the cable to the cable

channel with some zip-ties.

Figure 23: Attaching the cable to the cable channel

3. Drill a small hole or cut a gap into the rub-

ber sleeve and lead the cable through the inte-

rior trim to the receiver.

Figure 24: Entering the interior through the cable chan-

nel

Note:Many convertibles have composite trunk

lids. In such cases it will be necessary to create

a metal “ground plane”. This can be done by

gluing aluminum foil (at least 2 square feet)

underneath the trunk lid between the composite

lid and the liner.

It is important that the coaxial cable is

not damaged or kinked during the in-

stallation procedure.

Figure 25:Antenna mounting on composite

6SUV’s, Minivans and 5 Door

Vehicles

Figure 26: Minivan with Antenna Module

The antenna module should be located on the

centerline of the roof, not less than 4 inches

from the gap between the roof and tailgate.

Note the following:

•If the vehicle is equipped with a roof rack,

the crossbar should be placed at least 6

inches away from the antenna module.

Figure 27: Preferred mounting location

•It may be necessary to locate the antenna to

the right or left of center in order to avoid

“skid ribs” or brake light.

Figure 28:”Skid Ribs” and brakelight

Other roofs have a brake light in the back and

the cable may be routed through the brakelight

(see Pickup Trucks).

1. Follow steps 1 to 4 under “Sedans” to attach

the antenna module to the vehicle.

2. Route the cable between the roof and the

tailgate to the inside. Take advantage of any

existing cable channel or wiring conduit.

3. There are two alternative methods to route

the cable under the headliner and to the re-

ceiver:

a. The cable may be routed to the cable chan-

nel, lift up the channel and go through the

small opening and push the cable directly be-

tween sheet metal and headliner. This option is

recommended. The cable and the receiver may

be concealed behind the interior trim in the

back of the vehicle.

Figure 29: Cable routed through roof end and tailgate

under the rubber molding

b. Alternatively, the cable may be hidden under

the rubber molding following the metal groove

underneath the molding to the interior.

Figure 30: Hiding the cable under the rubber molding

Figure 31: Going inside under the interior trim

7Pickup Trucks

Figure 32: Pickup truck with antenna module

The antenna module should be mounted on the

centerline of the roof approximately 4 inches

from the rear of the cab.

The cables may be routed into the cab through

the brake light cavity.

1. Follow steps 1 to 4 under “Sedans” to attach

the antenna module to the vehicle.

Note: If the molding of the brake light is made

of rigid plastic/composite, it may be necessary

to drill a small hole or slot to route the cable.

Seal the hole with silicone compound after the

installation.

Figure 33: Brake light cavity

Figure 34: Completed installation

2. Route the cable through the interior trim to

where the receiver is located.

3. See Figure 19 under “Sedans” for connec-

tion to the receiver.

It is important that the coaxial cable

is not damaged or kinked during the

installation procedure.

Table des matières

Autres manuels Audiovox Antenne

Audiovox

Audiovox AN125 Manuel utilisateur

Audiovox

Audiovox AN350 Manuel utilisateur

Audiovox

Audiovox Tower Manuel utilisateur

Audiovox

Audiovox DTOC Manuel utilisateur

Audiovox

Audiovox HDTVlp Manuel utilisateur

Audiovox

Audiovox DBS-4500 Manuel utilisateur

Audiovox

Audiovox Skybox Mode d’emploi

Audiovox

Audiovox Terk XM6 Manuel utilisateur

Audiovox

Audiovox Terk SIRMarine Feuille d'instructions

Audiovox

Audiovox TERK XM4 Manuel utilisateur

Audiovox

Audiovox DBS-4800 Manuel utilisateur

Audiovox

Audiovox FM - TERK - Radio Antenna Manuel utilisateur

Audiovox

Audiovox TERK SIR6 Manuel utilisateur

Audiovox

Audiovox HDTVa - TV Antenna - Indoor Manuel utilisateur

Audiovox

Audiovox TERK TV1 Manuel utilisateur

Audiovox

Audiovox TERK SIR4 Feuille d'instructions

Audiovox

Audiovox FDTVO - TERK - TV Antenna Manuel utilisateur

Audiovox

Audiovox ANT3038XR Manuel d'utilisation et d'entretien

Audiovox

Audiovox TERK TV5 Manuel utilisateur

Audiovox

Audiovox HDTVo Manuel utilisateur

Audiovox

Audiovox TERK TV4 Manuel utilisateur

Manuels Antenne populaires d'autres marques

Alfa Network

Alfa Network APA-L01 Manuel utilisateur

Naval

Naval PR-422CA Manuel utilisateur

Feig Electronic

Feig Electronic ID ISC.ANTH200/200 Series Manuel utilisateur

TERK Technologies

TERK Technologies TV44 Manuel utilisateur

Directive Systems & Engineering

Directive Systems & Engineering DSE2324LYRMK Manuel utilisateur

HP J8999A Manuel utilisateur

MobilSat

MobilSat MSP-S Manuel utilisateur

Steren

Steren ANT-UHF 13 Manuel utilisateur

Novatel

Novatel 600-G Manuel d'utilisation

Radio Shack

Radio Shack Amplified VHF/UHF/FM Indoor Antenna Manuel utilisateur

TRENDnet

TRENDnet TEW-AO12O Manuel utilisateur

Radio Shack

Radio Shack 15-1837 Manuel utilisateur

CommScope

CommScope CMAX-OMFX-43M-I53 Manuel utilisateur

Ramsey Electronics

Ramsey Electronics DAP25 Manuel utilisateur

COBHAM

COBHAM SAILOR 800 VSAT Manuel d'utilisation et d'entretien

Trango Systems

Trango Systems AD900-9 Manuel utilisateur

Steren

Steren ANT-100 Manuel utilisateur

Proxim

Proxim 5054-PA-23 Manuel utilisateur