Audiovox Electronics IPD-SBBT Manuel utilisateur
www.audiovoxproducts.com
128-9136
OWNERS MANUAL
IPD-SBBT
2
INTRODUCTION
Congratulations on your purchase of the IPD-SBBT Sound Bar. The IPD-SBBT Sound Bar
has Bluetooth® capability.
Please read the instruction manual for this product before using. The documentation
provided will allow you to fully enjoy all the features this unit has to oer. Please save
this manual for future reference.
Bluetooth® is a trade mark of Bluetooth Special Interest Group (SIG) Inc.
WARNING! Never install this unit where operation and viewing could interfere with safe
driving conditions.
WARNING! Never disassemble the unit.
WARNING! To prevent injury from shock or re, never expose this unit to moisture or
water.
3
Package Includes:
Sound Bar IPD-SSBT Sound Bar Bracket
Mini USB charging Cable Owner’s Manual 3.5 mm AUX-IN Cable
4
IPD-SBBT FRONT VIEW
1. Previous and Volume Decrease ( ) Button:
Press the previous button to listen to the previous song on your Bluetooth® device. Press and
hold the previous button to decrease the volume.
2. Stop ( ) and Play
31
Button:
a) Bluetooth Audio
Press the button to stop playback. Press the button again to resume playback.
b) Bluetooth Phone
Press the stop button to end a call. Press the play button to answer a call.
3. Next ( ) and Volume Increase Button:
Press the next button to listen to the next song. Press and hold the next button to increase the
volume.
4. Blue LED
When the Sound Bar is turned on the LED will blink rapidly. When call is being received the
LED will blink rapidly. The LED will blink approximately every ve seconds when the Sound
Bar is not paired to a Bluetoooth® device. When the LED is ON the Sound Bar is connected to a
Bluetooth® device.
5. Red LED
When the LED is ON the battery charge is low.
6. Yellow LED
When the LED is ON the battery is being charged. When the LED is OFF the battery is fully
charged.
6 5 4
123
5
IPD-SBBT REAR VIEW
1. Device Holder
When the stand is in the open position, most tablet devices or cell phones can placed and held
within the stand notches.
2. STAND
Opens to hold most tablet devices or cell phones placed within the stand notches.
3. -VOL+ Adjustment
Rotate to increase or decrease the volume.
4. AUX IN Jack
Accepts a 3.5mm jack which is used to accept audio inputs from an external device. (e.g. - Non
Bluetooth players)
5. OFF/ON Switch
Slide switch used to turn the Sound Bar On and O.
6. DC 5V Mini USB Connector
Allows for the connection of a mini USB connector which is used the charge the Sound Bar
battery.
23 5
46
1
6
OPERATING INSTRUCTIONS
Power On/O
Use the rear panel slide switch to turn the Sound Bar ON and OFF. The LEDs on the front panel light
or blink depending on the Sound Bar status.
Battery Charging
To charge the Sound Bar battery, connect the mini USB connector to the rear panel DC 5 V
connector. Connect the USB connector to a USB port on a computer. Allow the unit to charge fully
before using it. The yellow LED is o when fully charged.
Volume Adjustment
Rotate the rear panel volume control to increase or decrease the volume. Also a Bluetooth® device
can also be used to increase or decrease the volume when the device and the Sound Bar are paired.
It is recommended leaving this control at maximum volume and controlling the volume with the
connected device.
AUX-IN Cable for Audio
The Sound Bar has an auxiliary audio input which can accept audio signals from various devices. The
AUX-IN jack on the rear panel accepts a 3.5mm jack.
Bluetooth® Pairing
NOTE: The following procedure is generic. Procedures for pairing Bluetooth® devices may vary slightly
manufacturer to manufacturer.
1. Turn the the Sound Bar ON. The blue front panel LED will blink rapidly.
2. Select the Bluetooth® setup option on the Bluetooth® device to be paired (please refer to the
instruction manual to enter Bluetooth® setup, turn Bluetooth® on/o, and perform pairing).
Access the Bluetooth® function and set the Bluetooth® function to ON.
3. A prompt to pair should appear on your Bluetooth® device. Accept the request and initiate the
pairing process. A prompt to enter a PIN number or passkey may appear. The default passkey
for the Sound Bar is “0000”.
4. At this point a prompt stating pairing complete should appear on your Bluetooth® device.
5. The front panel blue LED will be ON.
6. Once the Sound Bar is paired with the Bluetooth® device IPD-SBBT will appear on the
Bluetooth® device list screen.
7
NOTE: The Sound Bar memory can store a maximum four paired Biuetooth® devices. If a fth
Bluetooth® device is paired, the rst Bluetooth® device will be removed from the memory.
Bluetooth® Functions
Music:
Songs: To change songs press the Previous or Next button.
Volume Control: Press and hold the next button ( ) to increase the volume. Press and hold the
previous button ( )to decrease the volume.
Phone :
Answer/End a Call: When a cell phone is paired with the Sound Bar press the stop ( )/play (
31
)
button to end a call. Press the stop ( )/ play (
31
) button to answer a call.
Redial: Press and hold the stop ( )/ play (
31
) button to redial the last received number.
Voice dial: Press the stop ( )/play (
31
) button twice.
NOTE: The cell phone needs to support voice command functions.
During a phone conversation, pressing the next button ( ) and the previous button ( ) at the
same time, will turn OFF the Sound Bar’s microphone. Pressing and holding the next button ( )
and the previous button ( ) again will turn the Sound Bar’s microphone OFF.
Bluetooth Status Indicator:
Connecting a previously paired device: The blue LED blinks rapidly.
Pairing: The red and blue LEDs alternately.
Paired: The blue is ON.
Stand-by: The blue LED blinks in 5 seconds interval.
Songs: While playing songs the red and blue LEDs blink at the same time in 5 second intervals.
Receiving a call: When paired and receiving a call the blue LED blinks rapidly.
During Conversation: During a phone conversation the red and blue LEDs blink three times in 1
second intervals.
8
Sound Bar Device Stand (may not work with all devices)
1. Place the Sound Bar on a at surface and open
the rear panel stand as shown.
2. Place the device in the Sound Bar holding slot
which provide the best t for your device.`
3. The viewing angle of the device in the stand can be
adjusted by moving the two stands as shown.
9
Sound Bar Vehicle Installation
The Sound Bar can be attached to an optional Audiovox iPad protective case (IPD-1, IPD-2C, IPD-2HP,
IPD-2FM, sold separately) for in-vehicle installations. Refer to the gure below.
The included Sound Bar Bracket and optional Audiovox vehicle kit are required for vehicle
installations. The headrest post mount and protective case are not included in this package. For
further information, refer to the Audiovox website at www.audiovoxproducts.com.
Sound Bar
Sound Bar Bracket
Protective Case
Headrest Mount
Table des matières
Manuels Système de haut-parleurs populaires d'autres marques
Sondpex
Sondpex Active Speaker System and Digital Music... Manuel utilisateur
JVC
JVC NX-PN7 Manuel utilisateur
Marshall Amplification
Marshall Amplification AR-DM61-BT Manuel utilisateur
Yamaha
Yamaha NX-A01 - Speaker Sys Manuel utilisateur
SE Audiotechnik
SE Audiotechnik I-LINE Manuel utilisateur
Gemini
Gemini WRX-843 Series Manuel utilisateur