Audiosystem X-150.2 D Manuel utilisateur

High-Performance

Car- amplifier

designed and engineered by audio system Germany

owner‘s manual

the sound

since 1988

X-80. 4 D

X-150.2 D

by Audio system

X-150.2 D

X-80.4 d.

- 2-Channel High-Power Full-Range Digital amplifier

- Stable into 2 ohm stereo per channel and 4 ohm bridged mode

- Variable switchable Low Pass Filter from 40 to 450 Hz

- Variable switchable High Pass Filter from 20 to 4500 Hz

- Input Sensitivity: variable 200 mV maximum to 8 V minimum

- Multi-Way Protection Circuitry: overheating, overcurrent, short circuitry and

speaker DC protection

- Operating Voltage : DC 10 ~ 16 V power input

- Wired Remote Control RTC (optional)

- High-Power-Input (normally originial radio) with automatically „Turn-On“

- Adaptercable HLAC and rca hi (optional)

- 4-Channel High-Power Full-Range Digital amplifier

- Stable into 2 ohm stereo per channel and 4 ohm bridged mode

- Variable switchable Low Pass Filter from 40 to 4500 Hz

- Variable switchable High Pass Filter from 20 to 4500 Hz

- Input Sensitivity: variable 500 mV maximum to 4 V minimum

- Multi-Way Protection Circuitry: overheating, overcurrent, short circuitry and

speaker DC protection

- Operating Voltage : DC 10 ~ 16 V power input

- Wired Remote Control RTC (optional)

- High-Power-Input (normally originial radio) with automatically „Turn-On“

- Adaptercable HLAC and rca hi (optional)

READY

features

Congratulation on your purchase of your new x Series amplifier.

IMPORTANT: Before installation your power amplifier, we recommend to read the owner´s manual carefully and to

follow the instructions regarding connection and fitting exactly.

ATTENTION: Pay attention to advices and instructions of the car manufacturer.

IMPORTANT: Your proof of purchase is evidence of warranty claim for repair or replacement. Keep your proof of

purchase, manual and original packaging.

ATTENTION: Use of sound components can impair your ability to hear necessary traffic sounds and may constitute a

hazard while driving your automobile.

Audio SystemGermany accepts no liability for hearing loss, bodily injury or property damage as

a result of use or misuse of our products. We recommend installing the equipment by an authorized service center or

dealer. A professional fitting and connection is the requirement for further warranty and perfect sound.

xby A u dio s y stem

X-150.2 D / X-80.4 D.

+12V REM GND

BATTERY

GROUND remote connection

HEAD UNIT

fuse

Max.

30 cm

Power connection xby A u dio s y stem

3. +12 V Power connection:

Connect the +12 V contact of the amplifier with the supply cable via a fuse directly to the vehicle battery. Keep in

mind, that the length of the cable from fuseholder to vehicle battery has to be maximum 30cm. For the amplifier to

function at its best, use a high quality fuse holder and suitable cable preferably AWG 8-6 cable. This fuse protects the

amplifier and the vehicle against the possibility of a short circuit in the power cable.

4. Remote connection:

Connect the REM-terminal of the amplifier to the remote-output (automatic 12 V antenna-output) of the head unit.

Use a 0,5 - 1,5 mm power cable.

1. Battery disconnection:

First, disconnect the power supply of the

vehicle by removing the ground cable of the

battery.

2. Ground connection:

Connect the GND (ground) connection

of the amplifier with the car chassis.

Keep this cable as short as possible (not longer

than 50 cm) and use a suitable cross section

(AWG size 8-6).

Make sure, that the connection with the

vehicle chassis is free of paint, dirt and

dust.

a) Take care of a professional attachement. Pay attention, that no electrical cable, gas tank, hydraulic

breakes or other components get damaged.

b) There has to be enough cooling and air circulation. Avoid the installation in small closed boxes or close

to heatening parts.

c) Protect the amplifier from fluids, wetness, heat and foreign material as well as from other influences.

d) The amplifier is only to be built into vehicles with a 12 V DC power supply.

e) Never install the power supply cable with other original wires of the vehicle (gas cables), fan motors,

brand control moduls etc.

f) Install the signal cable (cinch cable) as well as the speaker cable far away of the power cables to avoid

troubles with the music signal.

g) The cables of your amplifier have to be installed, so that there is no danger of binding, squeezing or

breaking.

Please follow the instructions during the installation of your amplifier:

ATTENTION

X-150.2 D

The X Series amplifier offers RCA-Inputs, which are connected through cinch cables with the preamplifier-

outputs of the head unit. If the head unit (OEM-RADIO) has no RCA-Output, than it is possible to connect the speaker

output direct to RCA/Cinch-Input. Important: the Gain-Controller has to be adjusted to minimum, then carfully turn up

the volume. Input Mode has to be switched on „HI“. If signal is presented, the amplifier automacally turns on.

Adaptercable HLAC and RCA HI can be purchased at your specialized dealer. The RCA-outputs provide the

possibility to transfer the signal of the head unit to a 2. amplifier via a cinch cable (not possible for x-80. 4 D).

With the aid of the shiftable high- and low pass filter, the gain-controller and the bassboost you are able to adjust the

amplifier on to your prefered taste of hearing, the circumstances of the vehicle and to the speakers.

In this regard, AUDIO SYSTEM germany recommends to adjust your amplifier through a specialized

service center, dealer or a specialist.

X-80.4 D.

HE AD UN IT

Wired Remote Control

RTC (optional)

Wired Remote Control

RTC (optional)

for channel 3 + 4

to INPUT of

additional

AM PLIFIERS

HEAD UNIT

RCA connection

xby A u dio s y stem

1-Channel Bridged

Tri-Mode

2-Channel Stereo

speaker connection

Speaker

Impedance

4 ~ 8 Ohm

Speaker

Impedance

4 ~ 8 Ohm

Speaker

Impedance

2 ~ 8 Ohm

X 150.2 D

X-150.2 D

CH 1 CH 2

Spule

xby A udi o sy ste m

X-80.4 D.

2-Channel Mono

2-Channel Stereo + 1-Channel Mono Bridged

4-Channel Stereo

CH 1/2 CH 3/4

CH 3/4

CH 3CH 1

CH 2

CH 1

CH 2

CH 4

speaker connection

xby A u dio s y stem

Speaker

Impedance

4 ~ 8 Ohm

Speaker

Impedance

4 ~ 8 Ohm

Speaker

Impedance

2 ~ 8 Ohm

trouble shooting

This power amplifier is featured with an efficient protection system to prevent any damages like over-heating,

overvoltage, short-circuit and DC at the loudspeaker output.

Occuring an error the protection-LED will light in red. In order to check the problem, first turn down all levels of

the head unit, afterwards turn it off.

AMPLIFIER IS NOT

POWERED UP, NO LED IS

LIGHTENING

- ground connection professional connected?

- +12V powercable professional connected?

- remote cable professional connected?

- fuses inserted and alright?

- analyze voltage on the amplifier.

- cinch cable alrith and professional connected

- loudspeaker professional connected?

- head unit alright?

- amplifier too hot?

- short-circuit at the loudspeaker output?

- short-circuit caused by loudspeaker cable with vehicle chassi (ground)?

- input voltage too high (e.g.faulty generator)?

PROTECTION LED

ILLUMINATES GREEN

WHILE AMPLIFIER IS

SOUNDLESS

PROTECTION LED

ILLUMINATES RED

WHEN AMPLIFIER IS

POWERED UP

ERROR IN AMPLIFIER FUSE - ground professional connected?

- loudspeaker impedance alright?

! CAUTION !

Make sure when changing fuses to use the same value.

SOUND TOO LOW OR

LOW-DISTORTED SOUND

- input level control “GAIN” is set to match the head unit?

- output level control of the head unit alright?

- loudspeaker error?

- loudspeaker cable checked?

- crossover frequencies has been properly set?

(Check head unit, amplilfier, DSP, soundprozessor, equalizer,

frequency bandpassfilter...)

- ground connection professional connected?

- short-circuit caused by loudspeaker cable with vehicle chassi (ground)?

- cinchcable (RCA) and/or loudspeaker cabel installed too

close to the power connection cable?

- cinch ground (RCA) of the head unit alright?

HIGH HISS-ENGINE NOISE

IN SPEAKERS

Please contact your specialized dealer if the amplifier is still not working after it has been

checked with the error list!

For warranty adjustement / repairs the original invoice has to be attached!

Opening the power amplifier is leading to a lost of warranty in either case!

AT TEN TIO N

OVERHEATING

(PROTECTION LED

ILLUMINATES RED WHEN

AMPLIFIER IS POWERED UP)

- impedance alright?

- loudspeaker error?

- adequate airflow of the amplifier?

! CAUTION !

After cooling down, the amplifier turns on automatically.

xby A u dio s y stem

X-150.2 D

10 - 16 V

4x 80 W

4x 150 W

2x 300 W

>96 dB

40 ~ 4500 Hz

20 ~ 4500 Hz

10 Hz ~ 50 KHz (+/-1 dB)

< 0,029%

75 dB

40 A x 1

200 mV ~ 8 V

180(W) x 45(H) x 150(L) mm

Power Supply Voltage

Rated Power Output at 14,4 V

-RMS power @ 4 ohm stereo

-RMS power @ 2 ohm stereo

-RMS power @ 4 ohm bridged

Signal to Noise Ratio

Low Pass Crossover

High Pass Crossover / Subsonic filter

Frequency Response

THD@RMS Watts

Channel Separation

Fuse Rating

Input Sensitivity

Dimensions

X-80.4 D.

Power Supply Voltage

Rated Power Output at 14,4 V

-RMS power @ 4 ohm stereo

-RMS power @ 2 ohm stereo

-RMS power @ 4 ohm bridged

Signal to Noise Ratio

Low Pass Crossover

High Pass Crossover / Subsonic Filter

Frequency Response

THD@RMS Watts

Channel Separation

Fuse Rating

Input Sensitivity

Dimensions

10 - 16 V

2x 150 W

2x 250 W

1x 500 W

>96 dB

50 ~ 300 Hz

25 ~ 175 Hz

10 Hz ~ 50 KHz (+/-1 dB)

< 0,028%

75 dB

40 A x 1

200 mV ~ 8 V

180(W) x 45(H) x 150(L) mm

specifications

xby A u dio s y stem

Audio System Germany

Falltorstraße 6 - 76707 Hambrücken

designed and engineered by audio system Germany

the sound

since 1988

READY

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Audiosystem Amplificateur de voiture

Audiosystem

Audiosystem H-200.1 Manuel utilisateur

Audiosystem

Audiosystem C Series Manuel utilisateur

Audiosystem

Audiosystem X Series Manuel utilisateur

Audiosystem

Audiosystem Twister F6-360 Manuel utilisateur

Audiosystem

Audiosystem R Series Manuel utilisateur

Audiosystem

Audiosystem H 300.1 Manuel utilisateur

Audiosystem

Audiosystem X-80.4 D Manuel utilisateur

Audiosystem

Audiosystem C0-95.2 Manuel utilisateur

Audiosystem

Audiosystem AS4120 Manuel utilisateur

Audiosystem

Audiosystem H Series Manuel utilisateur

Audiosystem

Audiosystem R-1250.1 D-24V Manuel utilisateur

Audiosystem

Audiosystem C0-70.4 Manuel utilisateur

Audiosystem

Audiosystem H Series Manuel utilisateur

Audiosystem

Audiosystem X 100.2 Manuel utilisateur

Audiosystem

Audiosystem X 120.2 D Manuel utilisateur

Audiosystem

Audiosystem Twister F4 260 Manuel utilisateur

Audiosystem

Audiosystem M Series Manuel utilisateur

Audiosystem

Audiosystem CARBON Series Manuel utilisateur

Audiosystem

Audiosystem Twister F2-190 Manuel utilisateur

Audiosystem

Audiosystem M 75.4 Manuel utilisateur

Audiosystem

Audiosystem R 195.2 Manuel utilisateur

Audiosystem

Audiosystem H Series Manuel utilisateur

Audiosystem

Audiosystem R 1250.1 D Manuel utilisateur

Manuels Amplificateur de voiture populaires d'autres marques

Cyfre

Cyfre CHACDMA-819 Manuel utilisateur

MTX

MTX Thunder Marine TM904 Manuel utilisateur

MTX

MTX Thunder TA Super TA92001 Mode d’emploi

Lanier

Lanier 480-0239 Instructions d'utilisation et d'entretien

Kenwood

Kenwood KAC-642 Manuel utilisateur

Pioneer

Pioneer GM-D8500M Manuel utilisateur

Jensen

Jensen XA4150 Manuel utilisateur

Sony

Sony XM-405EQX Marketing Specifications Manuel utilisateur

Audiopipe

Audiopipe AQX-660.2 Manuel utilisateur

Clarion

Clarion APA2001 APA2001 APA2001 Guide de démarrage rapide

Sony

Sony XM-7547 Manuel utilisateur

Alpine

Alpine PDX11000 - Amplifier Manuel utilisateur

Steg

Steg Qx Mos 105.4x Manuel utilisateur

JL Audio

JL Audio HD900/5 Manuel utilisateur

Memphis

Memphis 16-MC5.700 Manuel utilisateur

Audiopipe

Audiopipe APSM-1150 Manuel utilisateur

Boss Audio Systems

Boss Audio Systems Riot GT1000M Manuel utilisateur

Kenwood

Kenwood KAC-PS811D Manuel utilisateur