AudioCodes Mediant 3100 Manuel utilisateur

1 |Page

Mediant™ 3100 SBC and Gateway

Quick Setup Guide

Welcome

Congratulations on purchasing your AudioCodes Mediant 3100 Session Border Controller (SBC) and Gateway,

hereafter referred to as device!

This document is only intended to provide basic setup instructions for initial access to the device and

connecting it to your network. For advanced configuration and cabling, refer to the device's User's Manual and

Hardware Manual respectively, which can be downloaded from AudioCodes website at

https://www.audiocodes.com/library/technical-documents.

Before you begin, please read the Safety Precautions on page 9.

Package Contents

Make sure that the following items (in addition to any separate-orderable items that you may have purchased)

are included with your shipped device:

2 x front-mounting brackets with six screws for 19-inch rack mounting

1 x grounding lug

1 x serial cable adapter

2 x AC power cables

Regulatory Information document

2 |Page

Physical Description of Front Panel

PWR

LED indicating power status:

Green On

The chassis is receiving power and the Power Supply modules are

operating normally.

Red On

One of the Power Supply modules is faulty.

Off

The chassis is not receiving any power.

FAN

LED indicating fan status:

Green On

The Fan Tray module is operating normally.

Red On

One or more fans of the Fan Tray module are faulty.

Off

The Fan Tray module is not receiving power.

SYS

LED indicating system status:

Green On

The device is operating normally.

Orange On

The chassis is approaching the high-temperature threshold (but not

critical).

Red On



Fatal error has occurred.

- or -



The chassis is approaching the critical high-temperature threshold.

Off

The device is booting up.

TEL

LED indicating status of E1/T1 PSTN interfaces:

Green On

Normal operation.

Orange On

Temporary out-of-service of one or more E1/T1 interfaces. (A device

reset may resolve the issue.)

Red On

Out-of-service of one or more E1/T1 interfaces.

Off

No power.

BITS

This LED is not used and reserved for future use.

3 |Page

LED indicating High-Availability (HA) status:

Note: HA will only be supported from a specific 7.4 software version.

Green On

The device is running in HA mode and is the Active unit.

Green Flashing

The device is running in HA mode and is the Redundant unit.

Orange On

The device is running in Standalone mode (i.e., HA not configured).

Red On

The device is the Active unit, but an HA synchronization failure exists

(e.g., HA Maintenance link failure).

Red Flashing

The device is the Redundant unit, but a failure exists in HA.

Off

The device is booting up, before HA synchronization.

RST

Reset pinhole button for resetting the device and restoring it to factory defaults:

To reset the device: Using a paper clip or any other similar pointed object, press and

hold down the button for at least 2 seconds (but no more than 10 seconds).

To restore the device to factory defaults: Using a paper clip or any other similar

pointed object, press down the button for at least 15 seconds (but not longer than 25

seconds).

CONSOLE

RS-232 serial port (RJ-45) for connecting to the device's Command-Line Interface (CLI).

USB 2.0 Type-A port, which can be used for storage capabilities using an external USB hard

drive or flash disk (disk on key).

Fan Tray module cover.

4 |Page

Physical Description of Rear Panel

S1 1-16

S2 17-32

RJ-48C ports for connecting T1/E1 PSTN trunk interfaces.

GE 1-8

8 x 100/1000Base-T (Gigabit) Ethernet ports (RJ-45) for connecting to the IP network.

Each port provides LEDs to indicate Ethernet status:

Green On

Ethernet link established.

Green Flashing

Data is being received or transmitted.

Off

No Ethernet link.

PS1 / PS2

2 x Power Supply modules. Each module provides a LED to indicate power supply status:

Green On

DC power output is good.

Orange Flashing

Power Supply module is not operating properly.

Off

Internal power supply malfunction or the power source is

disconnected.

5 |Page

Mounting the Device

The device is designed to be mounted in a standard 19-inch rack. This is done by placing it on a shelf (not

supplied) in a 19-inch rack and then securing it to the rack's posts, using front-mounting brackets (supplied).

1. Install a shelf in the 19-inch rack on which you will place the device.

2. Attach the two front-mounting brackets (supplied) to both sides of the chassis. Each bracket is secured

to the chassis using 9 screws (supplied).

3. Place the chassis onto the rack shelf.

4. Align the holes of the chassis' mounting brackets with the holes of the rack posts, as shown in the

following figure. Secure the mounting brackets to the rack posts, using 19-inch rack bolts (not

supplied). Each mounting bracket is secured to the rack using two bolts.

6 |Page

Powering the Device

The device can be powered from a standard alternating current (AC) electrical wall outlet or a DC power

source.

1. GROUNDING: Ground (earth) the device by crimping an electrically earthed strap of 8-AWG (minimum)

wire into the grounding lug (supplied), and then attaching the grounding lug to the chassis, as shown in

the following figure, making sure that the spring washer is located between the screw head and the

lug. Connect the other end of the grounding wire to the building's protective earth (in accordance with

regulations enforced in the country of installation).

2. AC POWER: For each Power Supply module, connect the line socket of the AC power cord (supplied) to

the device's AC power inlet, located on the rear panel. Connect the plug at the other end of the AC

power cord to a standard electrical wall outlet.

7 |Page

Assigning an IP Address

Use the device's factory default IP address (192.168.0.2/24 and Default Gateway 0.0.0.0) to initially access the

device's Web-based management interface and then change it to suit your network's addressing scheme for

subsequent connectivity.

1. Using a CAT-5e/6 shielded twisted pair (STP) straight-through RJ-45 Ethernet cable, connect Ethernet

port GE 1 or GE 2 (located on the rear panel) to the LAN port of your computer:

2. Change the IP settings of your computer to correspond with the device's default IP address and subnet

mask.

3. On your computer, open a standard Web browser (for example, Google Chrome), and then in the URL

field, enter the device's default IP address; the Web Login screen appears:

4. Type in the default username (Admin) and password (Admin), and then click Log In.

5. Open the IP Interfaces table (Setup menu > IP Network tab > Core Entities folder > IP Interfaces).

8 |Page

6. Select the OAMP interface ('Application Type' with OAMP + Media + Control), click Edit, and then in

the dialog box, modify the device's OAMP interface.

7. Click Apply to submit your changes; your connection with the device becomes unavailable at the

default IP address (due to the new IP address).

8. Change the IP settings of your computer to correspond with the new OAMP IP address and subnet of

the device.

9. Access the device again, but at its' new IP address, and then on the Web interface's toolbar, click the

Save button; the new IP address is now saved to the device's flash memory.

10. Re-cable the device to the required network. You can now access remotely the device's management

interfaces, using the new IP address.

Obtaining Software and Documentation

If you have a maintenance and support agreement with AudioCodes, you can download the device's latest

software version from AudioCodes' Services Portal at https://services.audiocodes.com (registered users only).

You can also view and download documentation relating to the device (such as the User's Manual and

Hardware Manual)on AudioCodes website at https://www.audiocodes.com/library/technical-documents.

9 |Page

Safety Precautions

The device must be installed and serviced only by qualified service personnel.

The device is considered as IPX0 non-water ingress protected and therefore, must be installed only

indoors.

Do not expose the device to water or moisture.

Ethernet cabling must be shielded and routed only indoors, and must not exit the building.

Do not open or disassemble this device. The device carries high voltage and contact with internal

components may expose you to electrical shock and bodily harm.

Make sure the device is installed in a well-ventilated location to avoid over heating of internal

components and subsequent damage.

Do not place any object on top of the device and make sure that sufficient clearance from the front and

rear are maintained to ensure proper airflow to avoid over heating of internal components.

Operate the device in an ambient temperature (Tma) that does not exceed 40°C (104°F).

The device must be installed only in restricted access locations that are compliant with ETS 300 253

guidelines where equipotential bonding has been implemented.

Operate the device only from the type of power source indicated on the chassis.

Installation of the device must be in accordance with national electrical codes and conform to local

regulations.

Use only the supplied AC power cord for connection to the power source.

The device must be connected to an electrical socket-outlet providing a protective earthing connection.

If you are using both Power Supply modules, connect each one to a different AC power supply source.

The two AC power sources must have the same ground potential.

10 |Page

About AudioCodes

AudioCodes Ltd. (NASDAQ, TASE: AUDC) is a leading vendor of advanced communications software, products

and productivity solutions for the digital workplace.

AudioCodes enables enterprises and service providers to build and operate all-IP voice networks for unified

communications, contact centers, and hosted business services.

AudioCodes offers a broad range of innovative products, solutions and services that are used by large multi-

national enterprises and leading tier-1 operators around the world.

International Headquarters

1 Hayarden Street,

Airport City

Lod 7019900, Israel

Tel: +972-3-976-4000

Fax: +972-3-976-4040

AudioCodes Inc.

200 Cottontail Lane,

Suite A101E,

Somerset, NJ 08873

Tel: +1-732-469-0880

Fax: +1-732-469-2298

Website: https://www.audiocodes.com/

MediaPack, What’s Inside Matters, OSN, SmartTAP, User Management Pack, VMAS, VoIPerfect, VoIPerfectHD, Your

Gateway To VoIP, 3GX, VocaNom, AudioCodes One Voice, AudioCodes Meeting Insights, AudioCodes Room Experience

and CloudBond are trademarks or registered trademarks of AudioCodes Limited. All other products or trademarks are

property of their respective owners. Product specifications are subject to change without notice.

Document #: LTRT-89820

Date Published: 26/05/2021

Autres manuels pour Mediant 3100

Table des matières

Autres manuels AudioCodes Contrôleurs

AudioCodes

AudioCodes Mediant 9000 SBC Instructions de montage

AudioCodes

AudioCodes Mediant 2600 SBC Instructions de montage

AudioCodes

AudioCodes Mediant 2600 Manuel utilisateur

AudioCodes

AudioCodes Mediant 4000 SBC Instructions de montage

AudioCodes

AudioCodes Mediant 4000B Manuel utilisateur

AudioCodes

AudioCodes RX-PAD Manuel utilisateur

AudioCodes

AudioCodes Mediant 2600 Manuel utilisateur

AudioCodes

AudioCodes Mediant 4000 E-SBC Instructions de montage

AudioCodes

AudioCodes Mediant 4000 SBC Manuel utilisateur

AudioCodes

AudioCodes Mediant 800C Manuel utilisateur

AudioCodes

AudioCodes Mediant 500 Instructions de montage

AudioCodes

AudioCodes Mediant 9000 SBC Instructions de montage

AudioCodes

AudioCodes RX-PAD Manuel utilisateur

AudioCodes

AudioCodes RX-PAD Manuel utilisateur

AudioCodes

AudioCodes Mediant 4000B SBC Instructions de montage

AudioCodes

AudioCodes Mediant 4000 SBC Manuel utilisateur

AudioCodes

AudioCodes Mediant 4000 Manuel utilisateur

AudioCodes

AudioCodes Mediant E-SBC Guide de démarrage rapide

AudioCodes

AudioCodes Mediant 4000 SBC Manuel utilisateur

Manuels Contrôleurs populaires d'autres marques

Digiplex

Digiplex DGP-848 Mode d'emploi

YASKAWA

YASKAWA SGM series Manuel utilisateur

Sinope

Sinope Calypso RM3500ZB Manuel utilisateur

Isimet

Isimet DLA Series Style 2 Manuel d'installation

LSIS

LSIS sv-ip5a Manuel utilisateur

Rockwell Automation

Rockwell Automation 1769-L31 Manuel utilisateur

Airflow

Airflow Uno hab Manuel utilisateur

ABB

ABB ACS580-01 drives Manuel utilisateur

Panasonic

Panasonic GM1 Series Manuel utilisateur

Emerson

Emerson SW93 Manuel utilisateur

AutoAqua

AutoAqua Smart ATO micro SATO-120P Manuel utilisateur

Panasonic

Panasonic FP? Positioning Unit RTEX Manuel utilisateur

Samson

Samson Type 5824 Manuel de service

Alpha IP

Alpha IP MIOB 21001 Manuel utilisateur

Siemens

Siemens OpenAir GMA 1 Series Manuel utilisateur

Surecom

Surecom SR-629 Manuel utilisateur

Fishman

Fishman TriplePlay Manuel utilisateur

Regulus

Regulus SRS1 T Manuel utilisateur