Atmel AT88SC-DK1 Manuel utilisateur

AT88SC-DK1 WELCOME AND QUICK START GUIDE

Dear Valued Customer,

Thank you for choosing CryptoMemory®for your security needs. As you may

already know, CryptoMemory provides low-cost powerful security for your product

authentication and secure data storage needs. To ensure you have the most

current information, we ask that you check the CryptoMemory product website at

www.atmel.com/products/SecureMem for any recent updates. We wish you an

exciting development experience and ask that you do not hesitate to contact us at

[email protected] for any assistance we can provide.

Best regards,

Your Atmel CryptoMemory Team

Downloaded from Arrow.com.

ÏÏÏÏ

Package Contents

1. 1 AT88SC-DK1 CD

2. 1 CryptoMemory adaptor board

3. 1 tube of CryptoMemory samples

4. 1 Black-Red patch cord

5. 1 Green-Yellow patch cord

ÏÏÏÏ

ADAPTING AT88SC-DK1 TO YOUR DEVELOPMENT SYSTEM

ÏÏÏÏ

System Requirements:

n1 GPIO header pin for TWI clock, SCL.

n1 GPIO header pin for TWI data, SDA.

n1 header pin for power, VCC.

n1 header pin for ground, GND.

ÏÏÏÏ

Software Setup

1. Install contents of AT88SC-DK1 CD into your PC

2. Check the README ﬁle for information on CryptoMemory Library Integration and Reference.

AT88SC-DK1 WELCOME AND QUICK START GUIDE Everywhere You Are®

Downloaded from Arrow.com.Downloaded from Arrow.com.

ÏÏÏÏ

Hardware Setup

STEP 1:

Insert a CryptoMemory device into

the SOIC socket

STEP 3:

Connect Clock and Data wires

Align PIN 0 of the SOIC package towards

the header-pins side of the adaptor board.

Use Black-Red patch cord

1. Connect the double-header end of the

Green-Yellow patch cord to the SCL-SDA

header pins of the adaptor board. Align

such that Green connects to SCL and

Yellow connects to SDA.

2. Connect the Green cord to your system

TWI clock.

3. Connect the Yellow cord to your system

TWI data.

Use Green-Yellow patch cord

1. Connect the double-header end of the

Green-Yellow patch cord to the SCL-SDA

header pins of the adaptor board. Align

such that Green connects to SCL and

Yellow connects to SDA.

2. Connect the Green cord to your system

TWI clock.

3. Connect the Yellow cord to your system

TWI data.

STEP 2:

Connect Power and Ground wires

www.atmel.com

Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.

ÏÏÏÏ

Troubleshooting

1. Make sure CryptoMemory is properly inserted and aligned in the SOIC socket. The

correct orientation places PIN 0 of the SOIC package towards the adaptor board header

pins. When correctly oriented, holding the adaptor board with header pins towards self

should present the marking texts on the CryptoMemory package right side up.

2. Verify your hardware setup for accurate signal and power connections.

3. Make sure VCC is connected to a high-drive power supply.

4. Make sure your system meets pull-up resistor requirements on signal lines as deﬁned in

CryptoMemory datasheets

5. Make sure to include noise ﬁltering capacitors between Vcc and GND at the device

level, if working with a noisy system.

6. Read and Write CryptoMemory’s Memory Test Zone (MTZ) ﬁeld to verify connectivity.

MTZ is free of all security requirements at all times.

5253-SMEM-05/07

Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.

Autres manuels Atmel Système de sécurité

Atmel

Atmel AT88CK9000 Manuel utilisateur

Manuels Système de sécurité populaires d'autres marques

Inner Range

Inner Range Concept 2000 Manuel utilisateur

Climax

Climax Mobile Lite R32 Instructions de montage

CADDX

CADDX NX-6 Manuel utilisateur

FBII

FBII XL-31 Series Manuel utilisateur

Johnson Controls

Johnson Controls PENN Connected PC10 Manuel utilisateur

Aeotec

Aeotec Siren Gen5 Manuel utilisateur

Blaupunkt

Blaupunkt SA 2700 Manuel utilisateur

IDEAL

IDEAL Accenta Manuel du propriétaire

AJAX

AJAX DoubleButton Manuel utilisateur

Swann

Swann SW-P-MC2 Manuel utilisateur

Ecolink

Ecolink Siren+Chime Manuel utilisateur

Digital Monitoring Products

Digital Monitoring Products XR150 Manuel utilisateur

EDM

EDM Solution 6+6 Wireless-AE Manuel utilisateur

Highway Safety Group

Highway Safety Group EA401 Manuel utilisateur

Siren

Siren LED GSM Manuel utilisateur

Detection Systems

Detection Systems 7090i Instructions de montage

Se-Kure Controls

Se-Kure Controls MicroMini SK-4841 Manuel utilisateur

Siemens

Siemens FDM273 Manuel utilisateur