Athesi AT-S2400 Manuel utilisateur
- 1 -
BARCODE SCANNER
AT-S2400
Configuration Guide
www.athesi.com
- 2 -
Table of Contents
Chapter 1 System Information
1.1 About this manual 3
1.2 How to set up the parameter-I 3
1.3 How to set up the parameter –II 4
1.4 Resetting the standard product default 4
Chapter 2 System Setup
2.1 Interface selection
2.1.1 Keyboard emulation parameters setting 6
2.1.2 RS-232 communication setting 11
2.2 Scanning mode selection 16
2.3 Beeper tone selection 17
2.4 String Options (Prefix & Suffix) 18
2. Setup Insertion 19
Chapter 3 BarCode parameters setting
3.1 UPC-A 23
3.2 UPC-E 26
3.3 EAN-13 29
3.4 EAN-8 31
3. Code39 33
3.6 Codabar 36
3.7 Code93 40
3.8 Code128 42
3.9 Interleaved2 of 4
3.10 Industrial 2of 47
3.11 Matrix 2 of 49
3.12 China Postage 1
3.13 MSI/Plessey 3
3.14 Code 32
3.1 Code 11 7
3.16 Telepen 9
3.17 Function Key Emulation &
Function Code & Appendix 61
- 3 -
Chapter 1 - System Information
1.1 About this manual
This User's Guide provides detailed programming instructions. Barcode
scanners are factory programmed for the most common communication
setting. If you need to change these settings, programming is accomplished
by scanning the bar codes in this guide.
1.2 How to set up the parameter
Step 1: Scan the start configuration barcode
Start Configuration
Step 2: Scan necessary label for parameters that meet your application
Step 3: Scan end configuration to save the changes
End Configuration
- 4 -
1.3 How to set up the parameter – II
Most of time the scanner only requests one read of parameters when
changing to new values. You will hear two beeps when you successfully
set to the new values. But for some special parameters, multiple reads are
needed to complete the configuration. When use these special parameters.
In some cases, you might need to read one or more barcodes, such as:
Hexadecimal barcodes. For example: prefix, suffix, etc.
Numeric barcodes. For example: inter-character delay, max/min length
To complete the change of setting you will need to read the “Confirm”
barcode after you read the parameter. Below is the flow chart to explain
two different configurations.
1.4 Resetting the standard product default
If you aren’t sure what programming options are in your
scanner, or you’ve changed some options and want the
factory settings restored, scan the Standard Product
Default Settings bar code below.
Standard Product Defaults Setting
- 5 -
Chapter 2 - System setup
2.1 Interface selection
The scanner is designed to switch easily from interfaces.
Remember to reset the interface before changing to PS/2 or RS232 cable.
No presetting is requested for USB interface. Scanning USB bar code after
the cable is changed and activating the scanner by plugging the USB cable
again. USB interface complies with HID keyboard which means the setting
of USB scanner is exactly the same like the default setting from keyboard.
Start configuration End configuration
ITEM OPTION
* KEYBOARD
RS-232
Interface Selection
USB
- 6 -
2.1.1 Keyboard emulation parameters setting
Start configuration End configuration
ITEM OPTION
*IBM AT
IBM XT
IBM PS/2 30-80
IBM 0
PS/2 2
，
30
NEC 9801
Reserved 1
Device Selection for keyboard
Interface
Reserved 2
- 7 -
Start configuration End configuration
ITEM OPTION
* USA
ITALIAN
SPANISH
FRENCH
GERMAN
JAPANESE
Multi-Language Support
Language for Keyboard Interface
Reserved 1
- 8 -
Start configuration End configuration
ITEM OPTION
* Disable
Function Key
Enable
* Disable Emulate External Keyboard
Enable
* Disable
ALT Mode
Enable
NOTE : Emulate External Keyboard
Scan the barcode below if you do not have an external keyboard.
After scanning the Emulate External Keyboard bar code, you must
power cycle your computer.
- 9 -
Start configuration End configuration
ITEM OPTION
* Disable
Caps Lock
Enable
* Disable
Num Lock
Enable
Inter Character Delay
(Default
：
00)
Ref: Appendix
（
00—64H
）
- 10 -
Start configuration End configuration
ITEM OPTION
None
* CR
Tab
ESC
Terminator
CR + LF
Block transmission delay
(Default
：
00)
Ref: Appendix
（
00—0AH
）
Keyboard Speed
(Default 00: high clock rate)
Ref: Appendix
（
00—08H
）
Table des matières
Manuels Lecteur de codes-barres populaires d'autres marques
POSMicro
POSMicro Datalogic PowerScan D7100 Manuel utilisateur
Marson
Marson MT780 Guide de configuration rapide
NCR
NCR RealPOS Manuel utilisateur
Motorola
Motorola SE3300 Guide de configuration rapide
Element
Element P130BT Manuel utilisateur
Motorola
Motorola Symbol LS3008 Manuel d'installation et d'exploitation
