ATD Tools ATD-3700 Manuel utilisateur
WARRANTY POLICY
The ATD-3700 Refrigerant Gas Leak Detector is warranted to be
free of defects in materials and workmanship for a period of two
years from the date of purchase. This warranty applies to all
repairable instruments that have not been tampered with or
damaged through improper use including unauthorized opening of
the unit. Please ship warranty units that require repair freight
prepaid to Service Center along with proof of purchase, return
address, phone number and/or email address.
Model ATD-3700
Refrigerant Gas Leak Detector
User Manual
Detects all CFC, HFC, HCFC
Refrigerants including blends
Certified
SAE J1627
INTRODUCTION
The ATD-3700 features a long life heated sensor technology that is
designed to detect the more current and difficult HFC refrigerants
such as R-134a in addition to all HCFC (R22) and CFC (R12)
refrigerants including SNAP approved hydrocarbon blends.
The ATD-3700’s unique digital leak size indicator takes the
guesswork out of whether or not to repair a small leak. The digital
display is independent from the audio alarm and sensitivity level,
allowing the precise pinpointing of the leak source.
The ATD-3700 does not require rechargeable batteries. An optional
detachable UV light will soon be available that clips on to the probe
to allow both electronic or UV detection with one tool.
FEATURES
•Unique numeric leak size
Indicator •Long life, stable sensor
•R134a sensitivity .05 oz/yr
•R22 sensitivity .025 oz/yr
•Designed to meet new SAE
2791 standard
•Automatic calibration and
reset to ambient
•Visual LED leak alarm near
sensor
•3 adjustable sensitivity levels
•Low battery indicator
•True mechanical pump
•Audio mute function
•Uses 4 AA alkaline batteries
•SAE J1627 Certifiable
•Comfortable Sanoprene grip
•Bright 3 LED detachable UV
light (optional)
•CE Certified
•2- year warranty includes
sensor
•Made in USA
1
Replacement Parts
Item Part Number
Sensor with Filter PRT3700-01
Sensor filters (5 pack)PRT3700-02
Leak Test Vial PRT3700-03
Parts Kit
(includes sensor, test vial, & filter kit) PRT3700-04
Carrying Case PRT3700-05
Product Specifications
Model # ATD-3700
Name Leak Detector, Refrigerant Gas
Sensitivity .05 oz/yr R134a
.025 oz/yr R22
Sensor Life > 300 hours
Response Time Instantaneous
Power Supply 4 AA Alkaline batteries
Battery Life 8 hours continuous
Warm up time < 20 seconds
Probe length 17 inches
Numerical Display 7 segment digital display (1 to 9)
Weight, lbs 1.5 lbs
Warranty 2 years (includes sensor)
6
Maintenance
Filter Ke
y
wa
y
ali
g
nment
Pull straight out (do not
twist)
to remove
sensor
Unscrew tip to
replace filter
Push straight on (do not
twist) to install sensor
Batteries:
Install Batteries: Remove screw located at rear end of unit and
pull down hinged battery door to open as shown. Insert positive
battery (+) end towards the front of the battery compartment
Sensor:
Replace Filter: Unscrew sensor tip as shown to replace filter.
Replace filter whenever it becomes visibly dirty or every 2 to 3
months depending on use.
Replace Sensor: Remove sensor by pulling out of socket. Install
the new sensor by aligning the notch in sensor cover with the raised
keyway on sensor socket holder (see figure below).
Note: Do not force sensor into socket. Misalignment can
damage the sensor pins.
5
+
ATD-3700
Operating Instructions
1. TURN ON: Press the ON/OFF button once to turn on and again
to turn off.
2. WARM UP: The detector automatically starts heating the
sensor. During the heating cycle, the digital leak size indicator
will flash 8 and the detector will sound a slow “beep”. Warm up
is usually less than 20 seconds.
3. READY: The detector is ready to begin searching for leaks
when the flashing 8 stops and the green sensitivity LED turns on.
The audio “beep” increases in frequency and probe LED begins
to blink steadily.
2
ATD-3700 Control Panel
Digital Leak Size
Indicator
Low Battery
Indicator
Sensitivity Level
Audio Mute &
Sensitivit
y
Level
Power
On/Off
Leak Size Indicator
The digital leak size indicator remains off normally but once a
leak is detected, a number from 1-9 will be displayed for all
HFC and HCFC refrigerants regardless of the sensitivity
setting.
The number will continue to increase or decrease depending
on the amount of refrigerant sensed. The maximum value will
be displayed once the leak source has been located. The
table below can be used to approximate the size of leak:
Maximum # displayed Leak Size (oz/yr)
1 -3 < 0.1
4-6 0.1 to 0.5
7-9 >0.5
Low Battery Indicator
Replace the 4 AA Alkaline batteries when the red LED on the
control panel is lit. Follow battery installation instructions
under Maintenance section.
Audio Mute Function
To silence or mute the audio beep and alarm signal, press the
MUTE button. To restore the audio sound, press the MUTE
button again. (Note: a few seconds is required to restore
sound if the mute button is pressed in rapid succession.)
3
Adjusting Sensitivity Levels
The Leak Detector will default to the NORM sensitivity level
automatically once the unit comes out of the warm up cycle and
the green LED will turn on.
To change sensitivity levels, press the SENS once for HI
sensitivity (red LED will turn on) and again for LO sensitivity
(yellow LED will turn on).
Leak Test Vial
The leak detector comes with a Leak Test Vial that allows the
user to make sure the detector is performing properly. To test:
1. Remove the plastic seal cap on top of the Leak Test Vial
by pulling it off (see fig. below).
2. Turn on the detector and allow the unit to complete the
warm up cycle.
3. Place the sensor close to the small hole in the top of the
Leak Test Vial. The beep rate should increase and the
Digital Leak Size Indicator should display a number from
4-6 indicating that the sensor and electronics are working
properly.
NOTE: Always remember to replace plastic seal cap after
leak test is completed. Replace Test Vial when the green
color is no longer visible.
4
Remove
Seal Cap
To test
Leak Test Vial
Autres manuels ATD Tools Capteur de sécurité
