ASTRO CDM-700 Series Manuel utilisateur
ASTRO
CDM-700 Series
(Covers Domestic 115V & European 220V Models)
Conveyor Stacker
USER’S GUIDE/PARTS CATALOG
This manual is intended solely for the use and information of Astro Machine Corp., its designated agents,
customers, and their employees. The information in this guide was obtained from several different
sources that are deemed reliable by all industry standards. To the best of our knowledge, that information
is accurate in all respects. However, neither Astro Machine Corp. nor any of its agents or employees shall
be responsible for any inaccuracies contained herein.
All rights reserved. No part of this book may be reproduced or transmitted in any form or by any means, electronic or mechanical, including
photocopying, recording, or any information storage and retrieval system, without permission in writing from the publisher.
INTRODUCTION
The CDM-700 Conveyor transports media from the Printer and stacks it. As the first piece of
stock exits the Printer, the motor-driven Conveyor Tapes under the Stacker Wheels move it. The
next piece of stock exits the Printer, overlaps the preceding piece, and is moved along the
Conveyor. After clearing the Stacker Wheels, the stock can be unloaded by hand without having
to stop the Printer.
SPECIFICATIONS*
Power Requirements:
Optional Availability:
115 VAC, 60 Hz, 9.0 AMP
220 VAC, 50/60 Hz, 0.5 AMP
Motor Circuit Breaker:
Fuse:
1 AMP
0.5 AMP
Speed Of Tapes:
0" - 250 feet per minute (variable)
Dimensions:
Width: 15" (38.1 cm)
L
ength: 34.5" (87.6 cm)
Height:
Table Top
Weight: 33 lbs. (15 kg)
* MANUFACTURER RESERVES THE RIGHT TO CHANGE
SPECIFICATIONS WITHOUT WRITTEN NOTICE.
SAFETY PRECAUTIONS
THIS EQUIPMENT PRESENTS NO PROBLEM WHEN USED PROPERLY.
OBSERVE SAFETY MEASURES WHEN OPERATING THE CONVEYOR:
READ THIS MANUAL CAREFULLY AND FOLLOW RECOMMENDED PROCEDURES.
¾ KEEP HANDS, HAIR, AND CLOTHING CLEAR OF ROLLERS, TAPES, AND
OTHER MOVING PARTS.
¾ ALWAYS TURN CONVEYOR OFF BEFORE ADJUSTING OR CLEANING.
¾ DISCONNECT POWER CORD WHEN MAKING ANY ADJUSTMENTS OR
PERFORMING ANY MAINTENANCE NOT COVERED IN THIS MANUAL.
WARNING!
ONLY CONNECT CONVEYOR
TO A PROPERLY GROUNDED OUTLET!
FAILURE TO DO SO CREATES RISK OF ELECTRICAL SHOCK!
USER GUIDE
-1-
Assembling Conveyor
1. Unpack Conveyor. Do not discard carton until
Conveyor is assembled.
2. Attach Receiving Tray to Conveyor with two
screws provided.
Positioning Conveyor
1. Place Conveyor on the same sturdy table or
workbench next to the Printer as shown.
2. Center Conveyor relative to Printer’s exit.
Operating Conveyor
Plug Conveyor into a properly grounded wall outlet
using power cord supplied.
CAUTION
CONVEYOR IS DESIGNED TO BE PLUGGED
INTO A GROUNDED OUTLET.
FOR YOUR SAFETY, DO NOT REMOVE
GROUND PIN FROM LINE CORD.
USER GUIDE
-2-
1. Turn Conveyor and Printer ON.
2. Feed stock through Printer and observe the way it is
received by the Conveyor.
3. Loosen Locking Knob [A] and adjust Stacker
Wheels so lead edge of media just touches Stacking
Rollers as it exits the Printer.
4. Adjust Speed Control to set the amount of overlap
between the pieces. (For less overlap turn Speed
Control clockwise, for more overlap turn Speed
Control counterclockwise.)
Reverse Operation
Conveyor is designed to run from right to left. It can also
operate from left to right. To switch operation direction,
first move Guide Roller Assembly and Stacking Tray to
opposite sides of the Conveyor. Then switch the
Reversing Switch (located under Conveyor) to the
reverse operating position.
Troubleshooting
If Conveyor fails to run, check for jammed
paper between Tapes and Roller. Also, check
Fuse and Motor Circuit Breaker and replace
or reset if necessary. Fuse Holders and Circuit
Breaker located on rear of Conveyor.
WARNING!
DISCONNECT POWER CORD WHEN CHECKING OR REPLACING FUSE!
ALWAYS REPLACE FUSE WITH THE SAME TYPE.
FAILURE TO DO SO MAY DAMAGE ELECTRONIC CIRCUIT BOARD.
USER GUIDE
-3-
Optional DTM-255/DTM-250 Conveyor Drop Tray Installation
DTM-255 Drop Tray is for Left-to-Right Operation. DTM-250 Drop Tray is for Right-to-
Left Operation. Assemble and install Conveyor Drop Tray on exit end of Conveyor:
1. Remove two screws attaching Stacking Tray to
Conveyor and remove Tray.
2. Remove four screws [A] that mount Front Cover
Plate to Conveyor.
DO NOT remove Front Cover Plate.
3. While holding Front Cover Plate in place, install
Drop Tray Support Bracket [B] using four screws
removed in Step 2.
4. Install Media Guide Roller Assembly using four
screws supplied [C]. Mount Media Guide Roller
Assembly as shown with Rollers resting on Exit
Roller of Conveyor.
5. Install Tray Base on Drop Tray
Support Bracket.
Tray adjusts up and down to allow
stacking more or less media.
6. Remove knobs from Guides.
Assemble Guides to Tray Base as
shown. Largest Guide is the Rear Stop
Guide. Second largest Guide is
installed on non-operator's side of
Conveyor and smallest Guide is
installed on operator's side as shown.
USER GUIDE
-4-
Optional 57E-600-10 Conveyor Leg Kit Installation
(for Use with M-Series Printers)
Install Conveyor Legs on the Conveyor to allow proper alignment with M-Series Printers.
CONTENTS OF KIT:
1. Conveyor Legs (2)
2. Screws (4)
INSTALL CONVEYOR LEGS:
1. Remove (4) Rubber Feet from bottom of Conveyor.
2. Attach Conveyor Legs across the bottom front and
rear of Conveyor using Rubber Foot holes [A] and
four screws included with Kit.
3. Reattach Rubber Feet to Conveyor Legs using
predrilled holes [B] provided.
USER GUIDE
-5-
Optional DK-700 Dryer Kit
Dryer Kit Includes: Front Exit Roller Assembly, Guide Roller Support, Front Roller
Support, Rear Roller Support, 2 Dryer Support Shafts, 8 mounting screws
1. Before installing DK-700 Dryer Kit, remove
these parts from the CDM-700 Conveyor.
A. Stacking Tray [A] (2 screws).
B. Guide Assembly [B] (4 screws).
Remove Operator’s Side Bracket first,
then the Rear Support Bracket.
2. Install new Rear Roller Support [C] using
two screws (as shown).
3. Hook Guide Roller Support over the shaft on
Rear Roller Support [1]. Install Front Roller
Support using two screws [2] (as shown).
4. Install Front Exit Roller Assembly by
attaching mounting brackets to Conveyor
Frame (as shown) using two screws on
each side [3].
USER GUIDE
-6-
5. Remove two Levers [4] and Bearing Washers
[5] from two Dryer Support Shafts [6]. Install
two Shaft Assemblies into holes provided in
Dryer (as shown). Reinstall Levers [4] and
Bearing Washers [5] on Shafts.
NOTE: When installing the two Levers [4],
make sure the cams on the opposite end of the
shaft are in the same position as the cams on
the Levers.
6. Dryer Assembly can now be placed in Support Brackets.
Make sure Bearing Washers are between the Support
Brackets and the cams (as shown).
NOTE: Bearing Washers should go between Support
Brackets and cams.
7. Plug cord supplied with Dryer into Dryer
receptacle, then into receptacle labeled "Dryer"
on the Conveyor. Then plug the Conveyor into
the wall outlet.
8. To operate the Dryer, set the two Levers so
media can pass under the Dryer without
interference. Then turn Dryer power switch ON.
Turn Conveyor ON.
Dryer and Guide Rollers can be adjusted from
side to side (by sliding them on Shaft
Assemblies) to accommodate varying media
sizes and print positioning.
NOTE: Dryer will not operate if Conveyor is not
turned ON.
CAUTION
DO NOT OPERATE DRYER IF BELTS ON CONVEYOR ARE NOT TURNING.
DO NOT BLOCK CONVEYOR EXIT WHEN USING DRYER.
USER GUIDE
-7-
Table des matières
