Assa Abloy Sargent Profile v.S1 Manuel utilisateur

A7763B

02/11

permission of Sargent Manufacturing Company is prohibited.

Proﬁle

PoE Cylindrical Lock

Installation Instructions

v.S1

Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited.

01/29/11

Changes or modiﬁcations to this unit not expressly approved by ASSA ABLOY Inc.

could void the user’s authority to operate the equipment.

SARGENT Mfg. Co. v.S Series locksets utilizing a door position switch (DPS) are not rated for,

or intended for use in life safety applications.

Table of Contents

Warning ....................................................................................2

General Description .................................................................3

Hardware Speciﬁcations .........................................................3

Electronic Speciﬁcations .........................................................3

Installation Wiring Overview ...................................................3

Installation Wiring ...................................................................4

Parts Breakdown .....................................................................9

Installation Instructions ........................................................11

Operational Check ................................................................19

1-800-810-WIRE • www.sargentlock.com • A7763B

Warning

FCC:

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of

the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equip-

ment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy

and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio com-

munications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the

user will be required to correct the interference at his own expense.

Industry Canada:

The term “IC:” before the radio certiﬁcation number only signiﬁes that Industry Canada technical speciﬁcations were met.

This Class A digital apparatus meets all requirements of the Canadian Interference Causing Equipment Regulations. Op-

eration is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device

must accept any interference received, including interference that may cause undesired operation.

Cet appareillage numérique de la classe A répond à toutes les exigences de l’interférence canadienne causant des

règlements d’équipement. L’opération est sujette aux deux conditions suivantes: (1) ce dispositif peut ne pas causer

l’interférence nocive, et (2) ce dispositif doit accepter n’importe quelle interférence reçue, y compris l’interférence qui

peut causer l’opération peu désirée.

02/11/11

A7763B 3

Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited.

Proﬁle Series v.S1 PoE Cylindrical Lock

General Description

The SARGENT Proﬁle Series v.S1 cylindrical lock is available with either an HID® Prox 125 kHz or 13.56 MHz

iCLASS® technology reader. It utilizes existing infrastructure and IEEE 802.3af PoE (Power over Ethernet)

technology as a proven alternative to traditional access control installations. The v.S1 is a self-contained

microprocessor-controlled access control product with non-volatile memory. It uses the existing network cable

to communicate with access control systems. The v.S1 lock holds a total of 2400 unique users per lock.

Using PoE technology coupled with approved third party software, this v.S1 online lock offers a complete, inte-

grated access control system.

The Proﬁle Series v.S1 cylindrical lock may be used for both indoor and exterior applications. A weather-

protective gasket is recommended for exterior applications.

HID and iCLASS are registered trademarks of HID Global Corporation.

Hardware Speciﬁcations

• Complete lockset with on-board memory

• Available with or without keypad

• ADA compliant, non-handed

• Latch: 1/2" standard

3/4" throw for ﬁre rated doors

(optional) (41- preﬁx)

• Deadlocking latch

• Inside lever retracts latch

• ANSI/BHMA Grade 1; UL Listed

3Electronic Speciﬁcations

• 2400 users per lock; 10,000 event audit trail

• Multiple time zone and holiday

access scheduling

• Centralized lock management

• Real time door status monitoring

• First-In unlock conﬁguration, either by time

or by user (selectable)

• Lock down capable

• Input Power: PoE Class 2 Device, as deﬁned

by IEEE 802.3af

• Supports HID® 125 kHz prox or 13.56 MHz

iCLASS® credentials (26 - 39 bit); supports

CSN reads for other common 13.56 MHz cards,

including MiFare, DesFire, and Felica

• Locks furnished for 1-3/4" and 1-3/8"

doors only

• Wire from EAC Panel to door must be

shielded with a drain (drain terminated

at EAC Panel controller)

Installation Wiring Overview

Supplied by Others

A. PoE Frame harness assembly

B. PoE data hinge from McKinney

(patent pending)

C. PoE door harness* from McKinney

D. DPS: Door Position Switch

(cylindrical and exit devices only)

E. Proﬁle Series v.S1 PoE lock

* Door width determines length

Network Cable

Network Switch (802.3af)

Surface Mount RJ45

Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited.

02/11/11

Proﬁle Series v.S1 PoE Cylindrical Lock

4 A7763B

6Installation Wiring

Cable: CAT 5e or higher

24 AWG shielded with drain wire

4-Pin

Molex-F Molex-F Molex-M

Cable: CAT 5e,

26 AWG stranded,

shielded, 100ohm

Wiring to TIA-568-B Standard

RJ45-M

Molex-M

RJ45-F Jack

Cable: CAT 5e or higher

24 AWG shielded, 100ohm

Approved Software

B-Splice

Crimp Connector

Certiﬁed Integrator (CI) supplies and terminates

the B-Splice connector and the

Male RJ45 connector from harness to

end user provided facility cable

Supplied by End User

PoE Switch

PoE

Lock

Ceiling

Supplied by CI

Patch Panel

Drain Wire Terminated on Rack

Ground

Ring Terminal

Secured to Lock

Mounting Plate

Drain Wire

PoE Switch is

terminated to

Earth ground

Patch Cable:

Patch Panel to

PoE Switch

4-Pin

PoE frame harness assembly (From McKinney)

PoE data hinge (Patent Pending) (From McKinney)

PoE door harness* (From McKinney)

DPS: Door Position Switch (cylindrical and exits only)

Proﬁle Series v.S1 PoE lock

* Order of installation may vary.

Refer to appropriate sections for instructions.

Frame-Side

Harness

Assembly

(15' length)

24AWG

Stranded

Wire for

Earth

Ground

inside

15' Frame

Harness

Cable

drain wire

concealed

in shrink

tubing

A B

Notes:

• Connectors go on only one

way. They cannot be placed

in an incorrect position.

• Do not force and do not

offset connectors.

• Be sure they are completely

seated (ﬂush).

02/11/11

A7763B 5

Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited.

Proﬁle Series v.S1 PoE Cylindrical Lock

A Frame Harness Installation

Suggested installation of components and wire harness supplied by McKinney:

RJ45-M

Molex-M

Cable: CAT 5e or higher

24 AWG shielded, 100ohm

B-Splice

Crimp Connector

Ceiling

Supplied by CI Cut end / ceiling-side PoE harness:

TIA-568-B Standard Wiring

Pair Number Wire PIN

1 White/Blue White/Blue 5

Blue 4

2 White/Orange White/Orange 1

Orange 2

3 White/Green White/Green 3

Green 6

4 White/Brown White/Brown 7

Brown 8

Do not confuse pair numbers with pin numbers. A pair number is used for

reference only (e.g.: 10Base-T Ethernet uses pairs 2 & 3). The pin numbers

indicate actual physical locations on the plug and jack.

1. Feed cut end of harness into hole on hinge-side through single access hole.

2. Push one of the connectors back through hole and feed into separate

access hole.

Hinge side of PoE harness:

Each of the hinge-side harness connectors should end up threaded through

a different access hole and matched to the same size pin connector from

the door harness:

• 4-pin male Molex connector.

• 6-pin male Molex connector with ground wire.

Frame-Side

Harness

Assembly

(15' length)

24AWG

Stranded

Wire for

Earth

Ground

inside

15' Frame

Harness

Cable

drain wire

concealed

in shrink

tubing

6-pin F

4-pin M

6-pin M

4-pin F

Drain Wire

Frame PoE Hinge (Patent Pending)

PoE Data Hinge

Hinge-side harness connectors:

• 4-pin male molex connector

• 6-pin male molex connector with ground wire

Lock-side harness connectors:

• Ring terminal

• (2) 4-pin connectors

• 4-pin Molex connector

• 4-pin connector

Notes:

• Connectors go on only one way. They cannot be

plugged to incorrect position.

• Do not force and do not offset connectors.

• Be sure they are completely seated (ﬂush).

Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited.

02/11/11

Proﬁle Series v.S1 PoE Cylindrical Lock

6 A7763B

PoE Door Harness

Order of installation may vary. Refer to appropriate sections for instructions.

1. Prop door open.

2. Tape the two lock-side 4-pin connectors to the ring terminal.

3. Using the ring terminal, carefully ﬁsh the assembly through the door channel to the lock.

4. Remove tape from ring terminal and door harness connectors.

Hinge-side harness connectors:

• 4-pin male Molex connector

• 6-pin male Molex connector with ground wire

Lock-side harness connectors:

• Ring terminal

• (2) 4-pin connectors

Ground

4-Pin

6-pin M

Cable: CAT 5e,

26 AWG stranded,

shielded, 100ohm

Ring Terminal Secured

to Lock Mounting Plate

4-pin F

Drain Wire

Installation Wiring (Continued)

PoE Lock

02/11/11

A7763B 7

Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited.

Proﬁle Series v.S1 PoE Cylindrical Lock

Wood Frame Metal Frame

Dim 1 3/8” 3/4”

Door Position Switch

1. Prep door according to proper template (Fig. D1).

2. Insert connector end of DPS through the raceway on the latch

edge of the door (Fig. D2).

Note: Only use collar when installing in a metal door.

3. To insert DPS, push wires through raceway toward lock prep.

4. Push DPS ﬁrmly into place by hand.

IMPORTANT: DO NOT TAP SWITCH WITH ANY TOOL.

5. To connect DPS to lock controller per diagram, refer to the wiring

instruction sections in the Installation Instructions section.

Fig. D2

Collar is used only

with metal doors.

Door Position

Switch (DPS)

Inside of Door

Raceway

Horizontal

of Strike

Door Position

Switch Hole

Vertical

of Strike

Dim 2

(See template)

Dim 1

Fig. D1

Strike for Cylindrical Lock

Frame

Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited.

02/11/11

Proﬁle Series v.S1 PoE Cylindrical Lock

8 A7763B

EPoE Lock Wiring

Unused

RX COM (WHITE)

Unused

RX NC (GREEN)

Unused

Motor B (BLACK)

Motor A (RED)

TB2

E1 TB1

Controller Board Connectors

(Inside Escutcheon)

J7, J4

JST Connectors

(From Hinge)

Ground Ring Terminal

(From Hinge to Top Left Escutcheon Screw)

D10

JP3

C37

R24

C10

R21

TP8

C31

DN1

C12

C16

C34

R14

JP4

C18

R22

C11

TP1

TP2

R10

D11

DN2

TP3

TP4

TP7

C32

TP5

TP6

R13

C35

R23

TP9

R12 C19

R25

C15

R11

C20

DN3

C13

C33

C14

C36

C17

MTG2

MTG3MTG4

MTG1

C21

R15

R16

D10

JP3

C37

R24

C10

R21

TP8

C31

DN1

C12

C16

C34

R14

JP4

C18

R22

C11

TP1

TP2

R10

D11

DN2

TP3

TP4

TP7

C32

TP5

TP6

R13

C35

R23

TP9

R12 C19

R25

C15

R11

C20

DN3

C13

C33

C14

C36

C17

MTG2

MTG3

MTG4

MTG1

C21

R15

R16

D10

JP3

C37

R24

C10

R21

TP8

C31

DN1

C12

C16

C34

R14

JP4

C18

R22

C11

TP1

TP2

R10

D11

DN2

TP3

TP4

TP7

C32

TP5

TP6

R13

C35

R23

TP9

R12 C19

R25

C15

R11

C20

DN3

C13

C33

C14

C36

C17

MTG2

MTG3MTG4

MTG1

C21

R15

R16

D10

JP3

C37

R24

C10

R21

TP8

C31

DN1

C12

C16

C34

R14

JP4

C18

R22

C11

TP1

TP2

R10

D11

DN2

TP3

TP4

TP7

C32

TP5

TP6

R13

C35

R23

TP9

R12 C19

R25

C15

R11

C20

DN3

C13

C33

C14

C36

C17

MTG2

MTG3

MTG4

MTG1

C21

R15

R16

D10

JP3

C37

R24

C10

R21

TP8

C31

DN1

C12

C16

C34

R14

JP4

C18

R22

C11

TP1

TP2

R10

D11

DN2

TP3

TP4

TP7

C32

TP5

TP6

R13

C35

R23

TP9

R12 C19

R25

C15

R11

C20

DN3

C13

C33

C14

C36

C17

MTG2

MTG3MTG4

MTG1

C21

R15

R16

D10

JP3

C37

R24

C10

R21

TP8

C31

DN1

C12

C16

C34

R14

JP4

C18

R22

C11

TP1

TP2

R10

D11

DN2

TP3

TP4

TP7

C32

TP5

TP6

R13

C35

R23

TP9

R12 C19

R25

C15

R11

C20

DN3

C13

C33

C14

C36

C17

MTG2

MTG3

MTG4

MTG1

C21

R15

R16

D10

JP3

C37

R24

C10

R21

TP8

C31

DN1

C12

C16

C34

R14

JP4

C18

R22

C11

TP1

TP2

R10

D11

DN2

TP3

TP4

TP7

C32

TP5

TP6

R13

C35

R23

TP9

R12 C19

R25

C15

R11

C20

DN3

C13

C33

C14

C36

C17

MTG2

MTG3MTG4

MTG1

C21

R15

R16

D10

JP3

C37

R24

C10

R21

TP8

C31

DN1

C12

C16

C34

R14

JP4

C18

R22

C11

TP1

TP2

R10

D11

DN2

TP3

TP4

TP7

C32

TP5

TP6

R13

C35

R23

TP9

R12 C19

R25

C15

R11

C20

DN3

C13

C33

C14

C36

C17

MTG2

MTG3

MTG4

MTG1

C21

R15

R16

D10

JP3

C37

R24

C10

R21

TP8

C31

DN1

C12

C16

C34

R14

JP4

C18

R22

C11

TP1

TP2

R10

D11

DN2

TP3

TP4

TP7

C32

TP5

TP6

R13

C35

R23

TP9

R12 C19

R25

C15

R11

C20

DN3

C13

C33

C14

C36

C17

MTG2

MTG3MTG4

MTG1

C21

R15

R16

D10

JP3

C37

R24

C10

R21

TP8

C31

DN1

C12

C16

C34

R14

JP4

C18

R22

C11

TP1

TP2

R10

D11

DN2

TP3

TP4

TP7

C32

TP5

TP6

R13

C35

R23

TP9

R12 C19

R25

C15

R11

C20

DN3

C13

C33

C14

C36

C17

MTG2

MTG3

MTG4

MTG1

C21

R15

R16

Ground Screw to Connector to E1

From

Lock

(+) 9VDC (RED)

(-) (BLACK)

AX/DPS NC (PINK)

AX/DPS COM (VIOLET)

Unused

EGND (GREEN)

DPS

COM (VIOLET)

NC (PINK)

TB2 E1 TB1

Power

From

Outside

Escutcheon

02/11/11

A7763B 9

Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited.

Proﬁle Series v.S1 PoE Cylindrical Lock

7Parts Breakdown 125 kHz Prox and 13.56 MHz iCLASS

Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited.

02/11/11

Proﬁle Series v.S1 PoE Cylindrical Lock

10 A7763B

ITEM PART NO. DESCRIPTION REQ’D

1 Outside Lever Reference Cylindrical/10 Line Catalog For Available Levers 1

2 Inside Lever Reference Cylindrical/10 Line Catalog For Available Levers 1

3 10-3016 Outside Escutcheon Assembly 1

4 10-3015 Inside Escutcheon Assembly 1

5 52-2431 125kHz Prox Only Bezel Assembly (PA) 1

52-2432 Keypad & 125kHz Prox Bezel Assembly (PK)

52-4420 13.56MHz iCLASS Only Bezel Assembly (S1-IA)

13.56 mHz reader assembly ships conﬁgured for PoE/Hardpower use.

52-4421 Keypad & 13.56 MHz iCLASS Bezel Assembly (S1-IK)

13.56 mHz reader assembly ships conﬁgured for PoE/Hardpower use.

6 52-4424 S1 Controller Assembly (Single Pulse); ships (Double Pulse) when ordered seperately and must

be ﬁeld conﬁgured to 10G77 (Single Pulse).

7 52-3855 Battery Cover Assembly 1

8 01-1212 Security Screw 1

9 52-2526 Screw Pack -Specify Finish

(Includes: Fire Stop Plate, Trim Mounting Screws and Security Allen Wrench)

10 52-3893 Door Position Switch 1

11 10-3048 Inside Rose Assembly 1

12 10-3049 Outside Rose Assembly 1

13 10-3409 Motorized RX Cylindrical Lock Assembly for options 10, 21, 22, 30, SC, SE, VA, VS (non handed)

10-3414 Motorized RX Cylindrical Lock Assembly for options 60, 63, 64 (non handed)

10-3419 Motorized RX Cylindrical Lock Assembly for options 70, 72, 65-73, 65-73-7P (non handed)

10-3439 Motorized RX Cylindrical Lock Assembly for options 80, 82, 82 F1 (non handed)

10-3440 Motorized RX Cylindrical Lock Assembly for options SF (non handed)

14 10-2000 2-3/4 Backset Latch (Standard) 1

15 10-2052 Cylindrical Screw Pack - Specify Finish

(Includes: Strike and Latch Screws, Push Pin Tool, and Strike Box)

16 Consult Factory 10 Line Cylinder 1

Parts Breakdown 125 kHz Prox and 13.56 MHz iCLASS, continued

Table des matières

Autres manuels Assa Abloy Verrouillage

Assa Abloy

Assa Abloy HES K20 Manuel utilisateur

Assa Abloy

Assa Abloy Aperio Series Manuel utilisateur

Assa Abloy

Assa Abloy IKON eCLIQ N111 BA3 Manuel utilisateur

Assa Abloy

Assa Abloy FAB INTERLOCK Manuel utilisateur

Assa Abloy

Assa Abloy SECURITRON CEPT-10 Manuel utilisateur

Assa Abloy

Assa Abloy Effeff 843G Manuel utilisateur

Assa Abloy

Assa Abloy HES KS200-640 Manuel utilisateur

Assa Abloy

Assa Abloy Yale Real Living YRD210-ZW Caractéristiques techniques

Assa Abloy

Assa Abloy ELECTRIC LOCK Manuel utilisateur

Assa Abloy

Assa Abloy Lockwood Pentagon 3P70 Manuel utilisateur

Assa Abloy

Assa Abloy HES 8500 Series Manuel utilisateur

Assa Abloy

Assa Abloy Securitron Magnalock Series Manuel utilisateur

Assa Abloy

Assa Abloy Yale Easy Manuel utilisateur

Assa Abloy

Assa Abloy 836S Manuel utilisateur

Assa Abloy

Assa Abloy Yale Smart Latch Manuel utilisateur

Assa Abloy

Assa Abloy Yale Real Living Assure Lock YRD226 Caractéristiques techniques

Assa Abloy

Assa Abloy OneSystem 819N Manuel utilisateur

Assa Abloy

Assa Abloy OneSystem 509N Instructions d'installation

Assa Abloy

Assa Abloy Sargent XC Series Manuel utilisateur

Assa Abloy

Assa Abloy Yale Real Living Assure Lock YRC216 Caractéristiques techniques

Assa Abloy

Assa Abloy Cabinet Lock Series Manuel utilisateur

Assa Abloy

Assa Abloy APERIO P100 Manuel

Assa Abloy

Assa Abloy UT5200 Series Guide de démarrage rapide

Assa Abloy

Assa Abloy Door Lock Manuel utilisateur

Manuels Verrouillage populaires d'autres marques

Magic

Magic 105 Manuel utilisateur

Gantner

Gantner GAT NET.Lock 7020 System Guide rapide

Wittkopp

Wittkopp Insys 7202 Manuel utilisateur

Dorma

Dorma Studio Classic Manuel utilisateur

Securam

Securam ECSL-601 Manuel utilisateur

Sudhaus

Sudhaus 3003 Manuel utilisateur

Safety 1st

Safety 1st 48517 Manuel utilisateur

Pado

Pado FDS-10 Manuel utilisateur

Esco

Esco systeQ Series Manuel utilisateur

COMPX

COMPX National D8951 Manuel utilisateur

secureo

secureo Key Box Manuel utilisateur

Stock Loks

Stock Loks C8713 Manuel utilisateur

COMPX

COMPX 1T-058 Manuel du propriétaire

Auslock

Auslock T11 Manuel utilisateur

ELCOM

ELCOM 7205 Manuel utilisateur

Stealth SAFES

Stealth SAFES ShadowVault Manuel utilisateur

Knox

Knox KeySecure 5 Manuel utilisateur

Kwikset

Kwikset 48334/01 Manuel utilisateur