Asante NetServer 6001 Manuel utilisateur
NetServer 6001/P/W
Video Server
Quick Guide
SecureNET
©2007 Asante Networks Inc., All rights reserved. NetCam is a registered trademark of Asante Network, Inc. www.asante.com
Enter Username: “root”, Password: “root”
Step
Enter the Main Page
Open A Microsoft Internet Exploer(IE) Window
1
.
Enter Camera IP address
Enter Home Camera Page
Enter Login Window
2
3
You Will Enter Home Page After Login
3
.
1
Install ActiveX
When the username and password are confirmed, a
control setup screen pops up under the IE address
bar. Click “Install ActiveX Control” to install the
controls.
2
The security warning screen aps.
Click Install.
Network Camera Live & Control Page
3
Step
The ActiveX is powered by Uniform Technologies and
You need to press Install to enable media viewer on
your IE browser ActiveX plug-in.
When ActiveX Plug-In is installed then you can view
video image. If you can not see, please select
streaming mode to HTTP.
Please refer to User Manual for detail operation.
Install Internet Explorer Plug-In Components
If No Video Image
You may need to check your PC environment including
(1) Window Firewall setting
(2) IE version should be 6.0 or above.
You may need to check router/firewall setting if you
view the video from the other side of router/firewall.
You may refer to user manual to learn this in depth.
Wireless networking
POWER
Alarm
Infrared inductor
Alarm
HUB
Video in
DVR
Digital Video
Recorder AMP
MIC
AMP
WAN Internet
PTZ Surveillance
RS485
Alarm input
Alarm output
2.
Connect Video cable.
1.
Connect your analog camera using
RS-485 to this product.
6.
Connect the switch hub to your PC
(as shown in the figure).
5.
Connect the product to the
switch hub(as shown in the figure)
.
4.
Connect the product to the
power source.
Link
Connect RS-485 Cable
4.
5.
6.
Step
Connect the product to the switch/hub and analog camera
Connect the video server using LAN.
3.
Connect your camera
to the power source
(as shown in the figure)
Connection diagram
If No Switch/Hub
You may connect Ethernet direct
from PC to product. However,
you will need to confirm your IP
address to the existing network.
You may also need a crossover
cable. It is highly recommended
that you have an IT professional
assist you.
Search for the product from your LAN. The factory
IP setting 192.168.0.20 appears on the screen.
Run the IP Finder.exe file from the CD.
1
4
Submit the change
Open the IE browser
Tools
Internet Options
Security
Custom Level
Note: This product supports IE 6.0 or above.
Step
Step
IP Address settings
Start
When you find the camera, click it and the settings
appear on the right side. Change the settings for the
new network environment you need.
Change the Internet Explorer settings
2
Search the product on the network
.
3
Changing the IP address, Netmask,
Default Gateway
4
Click Submit to validate new settings.
4
Confirmation
5
You may “search” again to confirm the change is
correct. After that, you can “exit”.
Bring Up Your IE browser
Start
Make sure that Level II, the commonly used default
security level, is set for the security.
2
Check
Steps
4
OK
Click OK to quit.
1
3
Select “medium” for security
Step
Wireless Setting
After setting of Ethernet IP address, enter the
Wireless Setting page.
1
Start
Wireless Setting
Wireless Bandwidth
Primary time of WLAN or 802.11 b/g offers 11Mbps
or 54mbps share bandwidth. The WLAN bandiwdth is
much less than that offered by Ethernet switch which
can sustain multiple channels of milti-mega bits of
realtime stream data like video.
Due to the bandwidth limitation of WLAN, It is
HIGHLY recommended to set video Quality below
1.5Mbps and below.
If your signal strength from wireless router/AP is
below 50%, either you need to adjuest AP or
camera position or boost antenna power. Please
consult your network manager.
Camera will automatically scanned Wireless APs
when you enter the page, or you may press “scan”
again. Importantly, you need to ensure your
WLAN AP is shown and with encyption enable.
2
Search/Select Wireless AP
.
Select Infrastructure mode, auto and enter SSID,
Select WEP Encryption to be 64 bits or 128bits
depending on your wireless router/AP setting.
Enter the exact same KEY that your used for the
wireless router/AP. Select DHCP or enter static IP
address based on your network plan. Press “Save”.
3
Setting the Network Paramaters
4
Refresh/reload page. After few seconds, you
should see the new wireless IP address.
Wireless Setting Confirm
Relocate Camera and Final Test
Step
Unplug the RJ45 on both router and the
network camera so that you can start
to use wireless independently.
Unplugged Ethernet
1
Relocate & Mount Device
.
Please mount the device to the preferred
location and power on the device.
2
You may “Test” if it has been connected and
operated smoothly.
1) Set Up your PC on the same WLAN subnet.
2) Use IP Finder to identify the Network Camera.
3) Use IE brower to view the video
4) Check to make sure that wireless signal strength
is at least 50%.
5) Check to make sure that the Video Quality is set
lower than 1.5Mbps
6) View the video.
Test & RUN
3
Ce manuel convient aux modèles suivants
3
Table des matières
Autres manuels Asante Serveur
