Ariston AURES MULTI Manuel utilisateur

AURES MULTI

INSTALLATION & OPERATION MANUAL

INSTANTANEOUS ELECTRIC WATER HEATER

GENERAL SAFETY INSTRUCTION

1. This manual is an integral part of the product. Keep it with in a safe place, and hand it on to

the next user/owner in case of change of property.

2. Read the instructions and warnings in this manual carefully, they contain important informa-

tion regarding safe installation, use and maintenance.

3. The appliance must be installed and commissioned by a competent person in accordance

with local legislation and health and safety regulations. All electrical power supply to the unit

must be isolated and made safe before you open the terminal block.

4. DO NOT use the appliance for anything other than its specied use. The manufacturer is not

liable for damage resulting from improper or incorrect use or failure to observe the instruc-

tions given in this manual.

5. Incorrect installation can result in damage to property and injury to persons and animals; the

manufacturer is not liable for the consquences.

6. DO NOT leave the packaging materials (staples, plastic bags, expanded polystyrene, etc.)

within the reach of children - they can cause serious injury.

7. This appliance can be used by children aged from 3 years and above and persons

with reduced physical, sensory or mental capabilities or lack of experience and

knowledge if they have been given supervision or instruction concerning use of the

appliance in a safe way and understand the hazards involved. DO NOT permit chil-

dren to play with the appliance. User cleaning and maintenance may not be done by

unsupervised children.

8. Any repairs, maintenance, plumbing and electrical connection must be done by qa com-

petent person using original spare parts only. Failure to observe the above instructions can

compromise the safety of the appliance and relieves the manufacturer of any liability for the

consequences.

9. The hot water temperature is regulated by a thermostat which also acts as a safety device to

prevent dangerous overheating.

10. The electrical connection must be done as indicated in this manual.

11. If the appliance is equipped with a power cable, the latter may only be replaced by an author-

ised service centre or professional technician.

12. Make sure to drain the appliance when it is out of service or in an area subject to subzero

temperatures.

13. Do not leave ammable materials in contact with or in the vicinity of the appliance.

14. DO NOT touch the appliance when barefoot or if any part of your body is wet

15. Before using the device and after routine maintenance, we recommend ushing the unit to

remove any debris .

16. Do not place anything under the water heater which may be damaged by a leak.

Symbol Meaning

Failure to observe this warning can result in injury, which may even be fatal in certain circumstances

Failure to observe this warning can msult in damage or injury, even to property; plants and animals

Observe the product's general and specic safety instructions.

GENERAL SAFETY STANDARDS

Ref. Warning Risk Symbol

1.Do not open the appliance or remove from its

installation

Electrocution hazard due to the presence of live electrical

equipment. Personal injury -overheated burns caused by

components and wounds caused by sharp edges

2. Do not start or stop the appliance by inserting/

pulling the power plug

Electrocution hazard due to damage to the power cord,

its plug or the socket

3. Do not damage the power cable Electrocution hazard due to bare live wires

4. Do not leave objects on the appliance Personal injury due to objects falling o the appliance as

a result of vibration

Damage to the appliance or other property due to

objects falling o the appliance as a result of vibration

5. Do not climb onto the appliance Personal injury due to falling o the appliance

Damage to the appliance or other property due to the

appliance itself detaching from its mounting

6. Do not clean the appliance without having rst

isolated the electrical power supply to the unit.

Electrocution hazard due to the presence of live electrical

equipment

7. Install the appliance to a solid wall which is not

subject to vibration

Danger of the appliance falling o the wall due to

structural collapse

8. Make the electrical connection with cables of

adequate cross-section

Danger of re due to overheating of undersized electrical

wires

9. Restore all safety and control functions after

working on the appliance and check that they are

operational before returning it to service

Damage or blocking of the appliance due to improper

control

10. Drain all components containing hot water, using

the bleed cocks, before handling them

Danger of burns

11. Descale the system as given in the products

"safety sheet"; when doing so, ventilate the

room, wear safety clothing, make sure not to mix

products, and protect the appliance itself and any

adjacent objects

Personal injury due lo contact of the skin and eyes with

add, inhalation or ingestion of noxious chemicals

Damage to the appliance and adjacent objects due to

corrosion by acid

12. Do not use insecticides, solvents or aggressive

detergents to clean the appliance

Damage to plastic and painted parts and assemblies

TECHNICAL CHARACTERISTICS

For the technical specications, refer to the nameplate (the nameplate is located on the right side of the

water heater).

PRODUCT INFORMATION

Model AURES

M 9.5 240V EU

Power (kW)

9.5

Voltage (V)

240

Phases

Mono

Installation

Multi point

Construction

Close outlet

Frequency (Hz)

50/60

Electric current (A)

39.6

Electrical diagram

III

Water Protection

IP25

Pipe Connection

1/2" BSP

Minimum water ﬂow (l/min)

2.1

Qelec (kWh)

2.224

Max water pressure

800 kPa (8 bar)

Load proﬁle

Lwa (dB)

ηwh

39%

Rated Volume (l)

0.45

Weight (kg)

2.2

Dimensions (mm)

304 x 220 x 110

The power consumption data in the table and the other information given in the Product Data Sheet (Enclosure

A to this manual) are dened in relation to EU Directives 812/2013 and 814/2013.

The products without the label and the data sheet for water heaters and solar devices, stipulated in regulation

812/2013, are not intended to be used in such assemblies.

Products equipped with a regulator knob have the thermostat positioned in the <ready to use setting indicated

in the Data Sheet (Enclosure A), according to which the relevant energy class has been declared by the

manufacturer.

The product should be connected only to an electrical supply with the relevant system impedance no

more than 0.237 ohm.

Restrictions to connection may be imposed by the supply authority on the use of equipment in the

actual relevant system impedance at the interface point on the user's premise exceeds 0.237 ohm.

This appliance is conforming with the international electrical safety standards IEC 60335-1 and IEC

60335-2-35. When present, The CE marking of the appliances attests its conformity to the following EC

Directives, of which it satises the essential requisites:

- LVD Low Voltage Directive: EN 60335-1, EN 60335-2-35, EN 60529, EN 62233, EN 50106.

- EMC Electro-Magnetic Compatibility: EN 55014-1, EN 55014-2, EN 61000-3-2, EN 61000-3-3,

EN 61000-3-11 and EN 61000-3-12.

- ERP Energy related Products: Eu812, Eu814, EN50193-1-2013

The UKCA marking of the appliances attests its conformity to the following UK legislation

- Electromagnetic Compatibility Regulations 2016

- Electrical Equipment (Safety) Regulations 2016

- The Ecodesign for Energy-Related Products and Energy Information (Amendment) (EU Exit) Regulations 2019

- The Restriction of the Use of Certain Hazardous Substances in Electrical and Electronic Equipment Regulations

2012

Installation Instructions:

The appliance must be installed and commissioned by a competent person in accordance with established

regulations and local health and safety regulations.

240 mm

44 mm 20 mm

131 mm

176 mm

1. Before performing any operations, disconnect the electricity using the external switch

2. Open the two screws located at the bottom of the device and remove the cover from base.

3. Fix the base horizontally against a wall or side of cabinet, the inlet and outlet water pipes are on the

down/bottom side of the unit. Use the four mounting screws provided.

cable

Flow restrictor

AERATOR

Hot

water

out

Cold

water in

only

4. Use the supplied water lter on the inlet water pipe line (see diagram)

5. Connect the incoming cold water pipe to the inlet connection point on the bottom right side and the

outgoing hot water pipe to the outlet water pipe on the bottom left side. Turn open the of water supply and

check there is no water leakage from the unit.

6. Use an all pole switch conforming with national laws in force (contact gap of at least 3 mm, preferably

equipped with fuses) to disconnect the appliance's power supply.

7. Connect the power cable to the terminal block inside the unit. The appliance must be earthed and the earth

cable must be xed to the terminal marked by the symbol .

8. Turn on the unit and check that it is operating as required.

9. Reconnect the cover to the base with 2 screws.

10. It is required that a Ground Fault Circuit Interrupter/Earth Leakage Circuit Breaker be incorporated in the circuit.

11. Make sure to install the pressure relief valve correctly (supplied with the product) before Inlet pipe.

12. It is required to install a ow control restrictor (AERATOR) at the sink or shower.

13. WARNING: UNIT MUST BE PROPERLY GROUNDED

14. THIS HEATER MUST HAVE ITS OWN INDEPENDENT CIRCUIT USING A CORRECTLY RATED CIRCUIT

BREAKER AND SUITABLE WIRE, SEE TABLE RECOMMENDED CABLE.

INSTALLATION

OPERATING INSTRUCTIONS

1. Your new Instant Water Heater is ow activated. Regulate the knob in one of the 3 setting power (I, II,

III) the product will switch ON once the hot water tap is turned on, the heating element will work and

warm the water only when there is a ow of water through the appliance.. You will need to allow at least

2.1 litres per minute to ow through the unit in order to activate the Instant Heating System. Run water

through the heater for a few minutes.

2. Be sure to every so often clean the spray head to assure a smooth water ow.

3. Be sure to every so often clean the incoming water lter.

4. Be sure to install your Instant Water Heater in a heated location. The appliance cannot be installed in

areas where the temperature may drop critically and there may be a risk that ice may form.

5. The user can adjust the hot water temperature regulating the setting power on the unit. the user can

choose from 4 dierent power settings:

- O - Heating element is o

- I - Only the 1st Heating element switches on.

- II - Only the 2nd heating element switches on.

- III - 1st and 2nd heating elements switch on, working together.

INSTALLATION REQUIREMENTS

A. A separate electrical supply is required.

B. The device must be connected to a separate circuit breaker.

C. The recommended electrical cable for supplying the device, see table I (next page)

WARNING!

BEFORE BEGINNING ANY WORK ON THE ELECTRICAL INSTALLATION BE SURE

THAT THE CIRCUIT BREAKER IS INTHE“OFF”POSITION TO AVOID DANGER OF

ELECTRICAL SHOCK

Inlet and

outlet at

the bottom

Outlet Inlet

Incorrect Installation

Correct Installation

See electrical diagrams at the end of the booklet.

ATTENTION

The water inlet of this appliance must be connected directly to a cold water mains supply.

Power

kW Loaded Heating setting Recommended

Cable

Recommended

Fuse Rating

220V 230V 240V

AURES M 9.5 240V EU

-- -- 9.5 4.7+4.8 kW H05VV-F 3x6mm² * 40A

• Operating water pressure 50-800 kPa (0.5-8 bar) • Water pressure operating power switch

• Standard 1/2"Ø compression inlet connection • Top-Left and Optional Top-right cable entry • Bottom-right water entry

UNIT DIMENSIONS: HEIGHT 220mm WIDTH 304mm DEPTH 110mm

Table 1: Recommended cable

Power Knob

Power LED

Water Inlet

Pressure Relief Valve

Filter

Water Outlet

* Recommended power cable size: 6mm2/10mm2(in the UK 10mm2is a requirement where it runs longer than 10 metres).

This product conforms to Directive WEEE 2012/19/EU.

The symbol of the crossed waste paper basket on the appliance indicates that at the end of its working

life the product should be disposed of separately from normal domestic household rubbish, it must be

disposed of at a waste disposal center with dedicated facilities for electric and electronic appliances or

returned to the retailer when a new replacement product is purchased. The user is responsible for the disposal of

the product at the end of its life at an appropriate waste disposal center. The waste disposal center (which using

special treatment and recycling processes eectively dismantles and disposes of the appliance) helps to protect

the environment by recycling the material from which the product is made. For further information about waste

disposal systems visit your local waste disposal center or the retailer from which the product was purchased.

Troubleshooting

SYMPTOM POSSIBLE CAUSE SOLUTION

Water not hot

enough

Too much water owing through

the heater

Reduction In the ambient

temperature

Water Pressure below of 100 kPa

Electrical Malfunction

Reduce the ow rate of the water via the

outlet tap.

Switch to higher temperature setting.

Check if the mains stop valve is fully open

and that the there are no other restriction

in the supply line.

Have the Heater unit checked by a

qualied eIectrician or contact your local

authorised distributor.

Water too hot Not enough Water owing through

the heater

Increase in the ambient temperature

Increase the ow rate via the outlet tap

Switch to lower temperature setting

Heater switch O

during use

Interruption of mains electrical

supply

ELSD trip, possible earth leakage

Check incoming power supply, MCB,

switches and supply cabling. Check earth

leakage and reset ELSD

If problem persists, call your local

authorised distributor for assistance.

Water ceases to

ow

Blockage of spray head, twisted or

blocked exible shower hose.

No water supply.

Clean or replace spray head, check for

free passage of water through hose.

Replace as necessary.

Check water supply, stop valve Open?

and no blockage.

Water

temperature

varies from hot to

cold during use

Water pressure has dropped below

min. level.

Increase hot water supply,

No hot water

despite fully open

hot water outlet

No electrical power

The activation ow rate needed to

turn on the heating element has not

been reached.

Check the circuit breaker and check

voltage at the wiring block.

Clean lter screen

• Turn circuit breaker o

• Open hot valve to release pressure from

the unit.

• Turn circuit breaker on.

ELECTRICAL WIRING

III

POWER SUPPLY

230V

=F1 - THERMOSTAT

=F4 - HEATING ELEMENTS

=F2 - POWER RELAY

=F5 - POWER LED

-H.E.1 -H.E.2

-S2

-S1

-H1

-H2

-H3

PCB INDICATOR

=F6 - COMMAND SWITCH

=F7 - REED RELAY

-T1

-RR

-K1 -K2

CZ2 CZ3

ACL1

57 °C85 °C85 °C

-RT1 -RT2

Product sizes

304

220

110

Optional cable entry

Top-left cable inlet is for cable until 10 mm

Optional top-right cable entry is only for power cable size: 6 mm

Table des matières

Autres manuels Ariston Chauffe-eau

Ariston

Ariston PRO1 R 50 V Manuel utilisateur

Ariston

Ariston GL 4 S Manuel utilisateur

Ariston

Ariston DUNE RS 10 PL EU Manuel utilisateur

Ariston

Ariston VELIS TECH PW ABSE 80 Manuel de la liste des pièces

Ariston

Ariston Unvented Hot Water Storage Cylinders Manuel utilisateur

Ariston

Ariston Ti Shape Small Mode d’emploi

Ariston

Ariston RT45PE-VN Manuel utilisateur

Ariston

Ariston HW65/9H Manuel utilisateur

Ariston

Ariston ABS VLS EVO INOX PW 30 Manuel de la liste des pièces

Ariston

Ariston WITH PUMP Manuel utilisateur

Ariston

Ariston A362ED Manuel utilisateur

Ariston

Ariston NEXT EVO X SFT Series Manuel utilisateur

Ariston

Ariston ABS LVS PREMIUM PW 80 Manuel utilisateur

Ariston

Ariston Andris Lux Series Manuel de la liste des pièces

Ariston

Ariston DUNE RS 10U PL EU Manuel utilisateur

Ariston

Ariston Nuos Evo Split 80 Manuel utilisateur

Ariston

Ariston DUNE1 Manuel utilisateur

Ariston

Ariston ST45PE-VN Manuel utilisateur

Ariston

Ariston GL 2.5 Manuel utilisateur

Ariston

Ariston VELIS LUX PW ABSE WIFI 30 Manuel de la liste des pièces

Ariston

Ariston GL 2.5 Manuel utilisateur

Ariston

Ariston AURES S 3.5 COM PL Manuel utilisateur

Ariston

Ariston 80 L Manuel utilisateur

Ariston

Ariston PRO1 Manuel utilisateur

Manuels Chauffe-eau populaires d'autres marques

Kenmore

Kenmore 153.582400 Manuel utilisateur

Applimo

Applimo Edel AIR Manuel utilisateur

STIEBEL ELTRON

STIEBEL ELTRON Eltronom SHU 5 S Manuel utilisateur

clage

clage E-Mini Series Manuel utilisateur

Toyotomi

Toyotomi Oil Miser OM-180 Manuel utilisateur

Bradford White

Bradford White EF Series Manuel utilisateur

Eccotemp

Eccotemp 40-H Manuel utilisateur

Dimplex

Dimplex ECSd125-580 Mode d’emploi

Dux

Dux 32FCR6N Manuel utilisateur

Toyotomi

Toyotomi Oil Miser OM-148 (Type D) Guide de dépannage

Noritz

Noritz N-132M Manuel d'instructions

TESY

TESY GCV7/4S 10047 Fiche technique

A.O. Smith

A.O. Smith Gphe 50 Manuel utilisateur

Koryo

Koryo KWHZF15Y Manuel utilisateur

Pentair

Pentair PSC-14-4-02 Manuel utilisateur

GE 40M06AAG Instructions de montage

Thermor

Thermor AEROMAX SPLIT 2 Manuel utilisateur

American Hometec

American Hometec AHQ-B03X Manuel utilisateur