Areca ARC-1883 Series Manuel utilisateur
SAS RAID Expander-CLI
USER Guide
Version: 1.2
Issue Date: April, 2018
ARC-1883ix-12/16/24 (12Gb/s SAS RAID Controller)
Copyright and Trademarks
The information regarding products in this manual is subject to change
without prior notice and does not represent a commitment on the part
of the vendor, who assumes no liability or responsibility for any errors
that may appear in this manual. All brands and trademarks are the
properties of their respective owners. This manual contains materials
protected under International Copyright Conventions. All rights
reserved. No part of this manual may be reproduced in any form or by
any means, electronic or mechanical, including photocopying, without
the written permission of the manufacturer and the author.
Contents
1. Introduction ................................................................ 4
1.1 Expander RS-232C Port Pin Assignment ...............................5
1.2 Start-up VT100 Screen ......................................................5
2. CLI Command .............................................................. 9
• HELP Command .................................................................9
• PASS Command .................................................................9
• LO Command .................................................................. 10
• LINK Command ............................................................... 10
• EDFB Command (Same as “DHPM”).................................... 13
• SYS Command................................................................. 15
• SPIN Command ............................................................... 16
• ST Command................................................................... 17
• LSD Command................................................................. 17
• SHOWLOGS Command...................................................... 19
• FDL Command ................................................................. 20
• Counters Reset Command ................................................. 21
• Sasaddr Command ........................................................... 23
• Sub Command................................................................. 23
SAS RAID Expander-CLI
4
1. Introduction
This Command Line Interface (CLI) is provided for you to congure
the Areca SAS RAID controller expander functions. The CLI is useful in
environments where a graphical user interface (GUI) is not available.
• Locations of RS-232 Port
• Establishing the Connection for the RS-232 Port
The CLI function can be done by using an ANSI/VT-100 compat-
ible terminal emulation program. You must complete the appropri-
ate installation procedure before proceeding with the CLI function.
Whichever terminal emulation program is used must support the
XMODEM le transfer protocol.
The serial port on the SAS RAID controller’s bracket can be used
in VT100 mode. The provided interface cable converts the RS232
signal of the RJ11 connector on the SAS expander controller into
a 9-pin D-Sub male connector. The rmware-based terminal SAS
expander management interface can access the expander through
this RS-232 port. You can attach a VT-100 compatible terminal or a
PC running a VT-100 terminal emulation program to the serial port
for accessing the text-based setup menu.
ARC-1883ix-16
SAS RAID Expander-CLI
5
Terminal requirement
Connection Null-modem cable
Baud Rate 115,200
Data bits 8
Stop 1
Flow Control None
1.1 Expander RS-232C Port Pin Assignment
To ensure proper communications between the SAS RAID controller
expander and the VT-100 Terminal Emulation, Please congure the
VT100 terminal emulation settings to the values shown below:
1.2 Start-up VT100 Screen
By connecting a VT100 compatible terminal, or a PC operating
in an equivalent terminal emulation mode, all CLI administration
functions can be exercised from the VT100 terminal.
There are a wide variety of Terminal Emulation packages, but for
the most part they should be very similar. The following setup pro-
cedure is an example Setup VT100 Terminal in Windows XP system
using Hyper Terminal use Version 3.0 or higher.
Step 1. Open the “Taskbar Start”/”Programs"/"Accessories"/"Com
mmunications"/"Heyper Terminal". (Heyper Terminal requires ver-
sion 3.0 or higher)
The controller RJ11 connector pin assignments are dened as be-
low.
Pin Assignment
Pin Denition Pin Denition
1 RTS (RS232) 4 GND
2 RXD (RS232) 5 GND
3 TXD (RS232) 6 GND
SAS RAID Expander-CLI
6
Step 2. Open “HYPERTRM.EXE”.
Step 3. Enter a name you prefer and then click “OK”.
SAS RAID Expander-CLI
7
Step 4. Select an appropriate connecting port and then click
"OK".
Step 5. Congure the port parameter settings and then click
“OK”.
Bits per second: 115200
Data bits: 8
Parity: None
Stop bits: 1
Flow control: None
Step 6. Open the le menu and select “Properties”.
SAS RAID Expander-CLI
8
Step 8. Congure the "Settings" items and then click "OK".
Function, arrow and ctrl keys act as: Terminal Keys
Backspace key sends: Crtl+H
Emulation: VT100
Telnet terminal: VT100
Back scroll buffer lines: 500
Now, The VT100 is ready to be used.
After you nished the VT100 Terminal setup, you may press "X"
key (in your Terminal) to link the expander CLI setup screen
and Terminal together.
Press “X” key to display the expander CLI utility screen on your
VT100 Terminal.
The CLI prompt is displayed in a DOS console window. Press
“H” to display the sub-manual.
Step 7. Congure the "Connect To" setting.
SAS RAID Expander-CLI
9
2. CLI Command
• HELP Command
This command provides an on-line table of contents, providing
brief descriptions of the help sub-commands. You can use the
<CLI> help to get detail information about the CLI commands
summary.
Syntax
CLI>help[Enter]
Example:
CLI>help
pass
lo
link
dhpm
sys
spin
st
lsd
showlogs
d
counters reset
sasaddr
• PASS Command
The pass command allows user to set or clear the expander box
password protection feature. Once the password has been set,
the user can only monitor and access the expander box setting by
providing the correct password. The password can accept max.
8 chars and min. 4 chars. The manufacture default password is
“0000”.
Syntax
CLI>pass [Enter]
- Set Password
- Logout CLI Shell
- Link Rate Control
- Bandwidth Optimizer
- System Information
- Drive SpinUp Control
- Store System Setting
- List Devices Status
- Show the Current Logs
- File Download
- Display/Reset all phy counters
- Display expander SAS address
SAS RAID Expander-CLI
10
Example:
CLI>pass
Old Password:****
New Password:****
Verify New Password:****
Password Changed But Not Save Permanently!
Note, use CLI command “st” to keep permanently.
• LO Command
To exit the selected expander box CLI shell, use the lo command.
Syntax
CLI> lo [Enter]
Example:
CLI>lo
Password:
• LINK Command
The link command allows you to set the operate device link rate
that has been connected on expander. Typical parameters include:
Max and Min disk speed connected the SAS expander box and
High and Low external cable link speed connected the SAS ex-
pander box.
1. Set external cable link speed rate
Syntax
CLI>link c[0] High Low]
Index: c[0] External Cable Index
The cable c0 is view from right to left or start from top to bot-
tom.
High-Rate, Low-Rate: [11|10|9] or [12g|6g|3g]
PS. Pls. Save Cong. & Reboot To Take Effect
CLI>st
Autres manuels pour ARC-1883 Series
2
Ce manuel convient aux modèles suivants
3
Table des matières
Autres manuels Areca Contrôleurs
