Arbor Technology FPC-3130 Manuel utilisateur

FPC-3130/3130V

Robust Box PC with

Intel®Atom™ D2550 Platform

User’s Manual

Version 1.1

2014.11

P/N: 4012313000110P

- 2 -

This page is intentionally left blank.

- III -

Revision History

Version Release Time Description

1.0 June 2012 Initial release

1.1 November 2014

The computer newly features a JACC1 Jumper for

automation and vehicle power mode control.

This gives rise to the following changes in this

manual:

2.1. Board Layout

2.2.2. Jumper Setting JACC1 description

added

3.7 Wiring the DC-Input Power Source divided

into Vehicle and Automation power mode

2.2.2. Jumper Setting SW1 & SW2 pin

conguration updated

The BIOS is updated and gives rise to the following

changes in this manual:

RS485 AutoFlow description added to 5.2.5

Super IO Configuration

5.2.1 ACPI Settings updated

5.3.2 South Bridge TPT section updaged

- IV -

This page is intentionally left blank.

- V -

Index

Contents

Revision History ......................................................................III

Chapter 1 - General Information..............................................1

1.1 Introduction................................................................2

1.2 Packing List................................................................3

1.3 Ordering Information.................................................3

1.4 The Installation Paths of CD Driver..........................4

1.5 Specications ............................................................5

1.6 Dimensions ................................................................7

1.7 Locating Controls and Connectors..........................8

Chapter 2 - The Engine of FPC-3130/3130V ...........................9

2.1. Board Layout...........................................................10

2.2. Jumpers and Connectors ......................................11

2.2.1. Jumpers & Connectors List................................ 11

2.2.2. Jumper Setting.....................................................12

2.2.3. Pin Assignments for Connectors .......................17

Chapter 3 - Installation and Maintenance.............................23

3.1 Memory, Mini-card & HDD Installation...................24

3.1.1 Removing Top Cover............................................24

3.1.2 Installing Memory Module....................................25

3.1.3 Installing Mini-card (optional)..............................26

3.1.4 Installing Hard Disk Drive ....................................29

3.2 How to Access CFast/SIM Card..............................30

3.3 Wall Mounting (optional).........................................31

3.4 VESA Mounting (Optional)......................................32

3.5 DIN Rail Mounting (optional) ..................................34

3.5.1 Face-Left/Right DIN Rail Mounting......................35

3.5.2 Face-Up/Down DIN Rail Mounting.......................36

3.5.3 Removing the Box PC from the DIN Rail ............37

3.6 Grounding the Box PC ............................................37

3.7 Wiring the DC-Input Power Source........................38

3.7.1 Vehicle Power Mode for FPC-3130V....................38

3.7.2 Automation Power Mode for FPC-3130...............39

Chapter 4 - Driver & AP...................................................................41

- VI -

Index

4.1 Prior to Installation..................................................42

4.2 Drivers ......................................................................43

4.2.1. CHIPSET ................................................................43

4.2.2. VGA ........................................................................46

4.2.3. Audio......................................................................50

4.2.4. LAN ........................................................................54

Chapter 5 - BIOS.....................................................................57

5.1 BIOS Main Setup......................................................58

5.2 Advanced Settings ..................................................59

5.2.1 ACPI Settings ........................................................60

5.2.2 CPU Conguration................................................61

5.2.3 IDE Conguration .................................................62

5.2.4 USB Conguration................................................63

5.2.5 Super IO Conguration ........................................64

5.2.6 H/W Monitor...........................................................65

5.3 Chipset Settings .......................................................66

5.3.1 Host Bridge ...........................................................66

5.3.2 South Bridge .........................................................68

5.4 Boot Settings ...........................................................71

5.5 Security.....................................................................72

5.6 Save & Exit ...............................................................73

Appendix .................................................................................75

Watchdog Timer (WDT) Setting.....................................76

- i -

The information in this document is subject to change without prior notice in

order to improve the reliability, design and function. It does not represent a

commitment on the part of the manufacturer.

Under no circumstances will the manufacturer be liable for any direct, indirect,

special, incidental, or consequential damages arising from the use or inability

to use the product or documentation, even if advised of the possibility of such

damages.

This document contains proprietary information protected by copyright. All

rights are reserved. No part of this document may be reproduced by any me-

chanical, electronic, or other means in any form without prior written permis-

sion of the manufacturer.

Declaration of Conformity

The CE symbol on your product indicates that it is in compliance with the di-

rectives of the Union European (EU). A Certicate of Compliance is available

by contacting Technical Support.

This product has passed the CE test for environmental specications when

shielded cables are used for external wiring. We recommend the use of

shielded cables. This kind of cable is available from ARBOR. Please contact

your local supplier for ordering information.

This product has passed the CE test for environmental specications when

shielded cables are used for external wiring. We recommend the use of

shielded cables. This kind of cable is available from ARBOR. Please contact

your local supplier for ordering information.

FCC Class B

This device complies with Part 15 of the FCC Rules. Operation is subject to

the following two conditions:

(1)This device may not cause harmful interference, and

(2)This device must accept any interference received, including interference

that may cause undesired operation.

NOTE:

This equipment has been tested and found to comply with the limits for a

Class B digital device, pursuant to Part 15 of the FCC Rules. These limits

are designed to provide reasonable protection against harmful interference

in a residential installation. This equipment generates, uses and can radiate

radio frequency energy and, if not installed and used in accordance with the

instructions, may cause harmful interference to radio communications. How-

- ii -

ever, there is no guarantee that interference will not occur in a particular instal-

lation. If this equipment does cause harmful interference to radio or television

reception, which can be determined by turning the equipment off and on, the

user is encouraged to try to correct the interference by one or more of the fol-

lowing measures:

-- Reorient or relocate the receiving antenna.

-- Increase the separation between the equipment and receiver.

-- Connect the equipment into an outlet on a circuit different from that to

which the receiver is connected.

-- Consult the dealer or an experienced radio/TV technician for help.

RoHS

ARBOR Technology Corp. certies that all components in its products are in

compliance and conform to the European Union’s Restriction of Use of Haz-

ardous Substances in Electrical and Electronic Equipment (RoHS) Directive

2002/95/EC.

The above mentioned directive was published on 2/13/2003. The main pur-

pose of the directive is to prohibit the use of lead, mercury, cadmium, hexava-

lent chromium, polybrominated biphenyls (PBB), and polybrominated diphe-

nyl ethers (PBDE) in electrical and electronic products. Member states of the

EU are to enforce by 7/1/2006.

ARBOR Technology Corp. hereby states that the listed products do not con-

tain unintentional additions of lead, mercury, hex chrome, PBB or PBDB that

exceed a maximum concentration value of 0.1% by weight or for cadmium

exceed 0.01% by weight, per homogenous material. Homogenous material

is dened as a substance or mixture of substances with uniform composition

(such as solders, resins, plating, etc.). Lead-free solder is used for all termina-

tions (Sn(96-96.5%), Ag(3.0-3.5%) and Cu(0.5%)).

SVHC / REACH

To minimize the environmental impact and take more responsibility to the

earth we live, Arbor hereby conrms all products comply with the restriction of

SVHC (Substances of Very High Concern) in (EC) 1907/2006 (REACH --Reg-

istration, Evaluation, Authorization, and Restriction of Chemicals) regulated

by the European Union.

All substances listed in SVHC < 0.1 % by weight (1000 ppm)

- iii -

Important Safety Instructions

Read these safety instructions carefully.

1. Read all cautions and warnings on the equipment.

2. Place this equipment on a reliable surface when installing. Dropping it or

letting it fall may cause damage

3. Make sure the correct voltage is connected to the equipment.

4. For pluggable equipment, the socket outlet should be near the equipment

and should be easily accessible.

5. Keep this equipment away from humidity.

6. Theopenings ontheenclosure areforair convection andprotectthe equipment

from overheating. DO NOT COVER THE OPENINGS.

7. Position the power cord so that people cannot step on it. Do not place

anything over the power cord.

8. Never pour any liquid into opening. This may cause re or electrical shock.

9. Never open the equipment. For safety reasons, the equipment should be

opened only by qualied service personnel.

10. If one of the following situations arises, get the equipment checked by

service personnel:

a. The power cord or plug is damaged.

b. Liquid has penetrated into the equipment.

c. The equipment has been exposed to moisture.

d. The equipment does not work well, or you cannot get it to work according

to the user’s manual.

e. The equipment has been dropped or damaged.

f. The equipment has obvious signs of breakage.

11. Keep this User’s Manual for later reference.

About This User’s Manual

This User’s Manual is intended for experienced users and integrators with

hardware knowledge of personal computers. If you are not sure about any

description in this User’s Manual, please consult your vendor before further

handling.

Warning

The Box PC and its components contain very delicately Integrated Circuits (IC).

To protect the Box PC and its components against damage caused by static

electricity, you should always follow the precautions below when handling it:

1. Disconnect your Box PC from the power source when you want to work on

the inside.

- iv -

2. Use a grounded wrist strap when handling computer components.

3. Place components on a grounded antistatic pad or on the bag that came

with the Box PC, whenever components are separated from the system.

Replacing the Lithium Battery

Incorrect replacement of the lithium battery may lead to a risk of explosion.

The lithium battery must be replaced with an identical battery or a battery type

recommended by the manufacturer.

Do not throw lithium batteries into the trashcan. It must be disposed of in

accordance with local regulations concerning special waste.

Technical Support

If you have any technical difculties, please consult the user’s manual rst at:

ftp://ftp.arbor.com.tw/pub/manual

Please do not hesitate to call or e-mail our customer service when you still cannot

nd out the answer.

http://www.arbor.com.tw

E-mail:info@arbor.com.tw

Warranty

This product is warranted to be in good working order for a period of one year

from the date of purchase. Should this product fail to be in good working order

at any time during this period, we will, at our option, replace or repair it at no

additional charge except as set forth in the following terms. This warranty does

not apply to products damaged by misuse, modications, accident or disaster.

Vendor assumes no liability for any damages, lost prots, lost savings or any

other incidental or consequential damage resulting from the use, misuse of, or

inability to use this product. Vendor will not be liable for any claim made by any

other related party.

Vendors disclaim all other warranties, either expressed or implied, including but

not limited to implied warranties of merchantability and tness for a particular

purpose, with respect to the hardware, the accompanying product’s manual(s)

and written materials, and any accompanying hardware. This limited warranty

gives you specic legal rights.

Return authorization must be obtained from the vendor before returned

merchandise will be accepted. Authorization can be obtained by calling or faxing

the vendor and requesting a Return Merchandise Authorization (RMA) number.

Returned goods should always be accompanied by a clear problem description.

Autres manuels pour FPC-3130

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Arbor Technology Ordinateur de bureau

Arbor Technology

Arbor Technology ARES-1983H Series Manuel utilisateur

Arbor Technology

Arbor Technology Rigid-750 Manuel utilisateur

Arbor Technology

Arbor Technology FPC-7900 Manuel utilisateur

Arbor Technology

Arbor Technology FPC-791 Series Manuel utilisateur

Arbor Technology

Arbor Technology LYNC-817 Series Manuel utilisateur

Arbor Technology

Arbor Technology FPC-3130 Manuel utilisateur

Arbor Technology

Arbor Technology FPC-7500 Series Manuel utilisateur

Arbor Technology

Arbor Technology Rigid-314 Manuel utilisateur

Arbor Technology

Arbor Technology ARES-1230 Manuel utilisateur

Arbor Technology

Arbor Technology IEC-3300 Manuel utilisateur

Arbor Technology

Arbor Technology ARTS-2870 Manuel utilisateur

Arbor Technology

Arbor Technology FPC-810 Series Manuel utilisateur

Arbor Technology

Arbor Technology Rigid-770 Series Manuel utilisateur

Arbor Technology

Arbor Technology Arpex-1610 Manuel utilisateur

Arbor Technology

Arbor Technology FPC-9107 Series Manuel utilisateur

Arbor Technology

Arbor Technology FPC-7800 Series Manuel utilisateur

Arbor Technology

Arbor Technology BPC-500-5820 Manuel utilisateur

Arbor Technology

Arbor Technology M1858 Manuel utilisateur

Manuels Ordinateur de bureau populaires d'autres marques

HP m9060n - Pavilion - Elite Fiche technique

Asus

Asus E210 Series Manuel utilisateur

Dell

Dell Inspiron 600m Manuel utilisateur

Dell

Dell Inspiron 3662 Manuel utilisateur

TotalFlow

TotalFlow uFLO Manuel utilisateur

HP Presario SV7000 - Desktop PC Manuel utilisateur

HP ProDesk 400 G5 Manuel

Logitech

Logitech MK320 Manuel utilisateur

Dell

Dell XPS 730 H2C Manuel utilisateur

Sony

Sony Vaio Series Manuel utilisateur

Sony

Sony VGC-LT32E - Vaio All-in-one Desktop Computer Manuel utilisateur

Alto

Alto MD 250 Manuel utilisateur

Lenovo

Lenovo ThinkCentre Edge 72 Manuel

Lenovo

Lenovo ThinkStation D20 Manuel

Sony

Sony VAIO VGX-TP1 Series Manuel utilisateur

Asus

Asus Eee Box B204 Manuel utilisateur

Dell

Dell Optiplex 9010 All In One Manuel utilisateur

HP Z1 Manuel utilisateur