Aqualisa iSys ISD.B3.DS.14 Manuel utilisateur
iSys Digital rem te c ntr l installation instructions Page 1
iSys
Digital
Rem te c ntr l
Installati n guide
TM
iSys Digital rem te c ntr l
ISD.B3.DS.14
iSys Digital rem te c ntr l installation instructions Page 2
iSys Digital rem te c ntr l
iSys Digital rem te c ntr l installation instructions Page 3
Literature not shown
C mp nents
iSys Digital rem te c ntr l installation instructions Page 4
Important information
The iSys Digital remote control is a remote button which provides a secondary method of ‘Start/stop’ for iSys Digital
shower systems. When used with the iSys Digital diverter system, the remote can operate each outlet by pushing and
holding the ‘Start/stop’ button for a few seconds as required. The remote control may be sited inside the showering
area, as long as it is not subjected to continuous spray, or it can be sited outside the showering area – up to 10
metres from the Digital processor.
The iSys Digital remote control is not suitable for use with any other Aqualisa Digital product range.
THIS PRODUCT UST BE INSTALLED BY A CO PETENT PERSON IN ACCORDANCE WITH ALL RELEVANT CURRENT
WATER AND ELECTRICAL SUPPLY REGULATIONS.
ALL SHOWERS REQUIRING AN ELECTRICAL CONNECTION UST BE INSTALLED BY A QUALIFIED PERSON
FOLLOWING THE LATEST REVISION OF BS7671 (WIRING REGULATIONS) AND CERTIFIED TO CURRENT BUILDING
REGULATIONS.
This product is suitable for domestic use only.
This product is supplied complete with a 2 year guarantee.
iSys Digital rem te c ntr l installation instructions Page 5
Installation instructions
iSys Digital rem te c ntr l
In addition to the guide below it is essential that the written
instructions below are read and understood and that you have all
the necessary components (shown overleaf) before commencing
installation. Failure to install the product in accordance with these
instructions may adversely affect the warranty terms and
conditions. Do not undertake any part of this installation unless you
are competent to do so. Prior to starting, ensure that you are
familiar with the necessary plumbing regulations required to install
the product correctly and safely.
THE DIGITAL PROCESSOR UST BE ISOLATED FRO THE AINS
POWER SUPPLY PRIOR TO INSTALLING THE ISYS DIGITAL RE OTE
CONTROL.
!
F r use with single utlet iSys Digital sh wer systems
IF FITTING THIS PRODUCT WITH AN ISYS DIGITAL SINGLE
OUTLET SHOWER SYSTE , PLEASE FOLLOW THE FITTING
INSTRUCTIONS BELOW.
!
iSys Digital rem te c ntr l installation instructions Page 6
Using the back plate as a
template, mark the position of
the fixing screws and a Ø16mm
hole for the data cable entry
point. The cable entry point
should be made in the top right
hand corner of the back plate
recess, to ensure the two holes
are kept separate.
1
Wiring diagram
10m Data
Cable
10m Data
Cable
Prepare suitable wall fixings to accommodate no. 8 non-rusting
countersunk head screws of a suitable length (not included).
2
Pull the data cable through
before securing the back plate to
the wall using suitable no. 8 non
rusting countersunk screws.
4
Push the data cable plug into the
back of the button fully home to
ensure a water tight seal making
sure the seal is no longer visible.
5
iSys Digital rem te c ntr l installation instructions Page 7
Prepare a suitable route and install the 10m low voltage data
cable leaving a working end of at least 70mm including the
connector plug. The end of the data cable closest to the
processor should terminate at a maximum of 500mm from
the processor to allow for connection to the data cable
connection block.
3
DATA CABLES UST BE PROTECTED BY SUITABLE SHEATHING OR
CONDUIT IN THE EVENT OF SERVICING AND AINTENANCE.
!
iSys Digital rem te c ntr l installation instructions Page 8
Secure the button to the back plate
by carefully but firmly pushing the
button assembly onto the locking
clip at the bottom of the back
plate.
7
Locate the slot at the top of the
button assembly, onto the locating
peg at the top of the back plate
assembly, and lower the
button into position.
6
To release the button, insert a
small flat bladed screw driver into
the small slot at the bottom of the
button assembly, to release the
locking clip, taking care to avoid
damaging the plated surface.
Carefully lift the button out and
up off of the back plate top
locating peg.
!
BEFORE ANY ELECTRICAL ADJUST ENT IS ATTE PTED, THE
ELECTRICITY SUPPLY UST BE TURNED OFF AT THE AINS
SWITCH.
ELECTRICAL INSTALLATION AY ONLY BE CARRIED OUT BY
A QUALIFIED PERSON.
!
iSys Digital rem te c ntr l installation instructions Page 9
The Digital processor features a
secondary data cable socket next
to the main data cable connection
for use with the Digital remote
control secondary ‘Start/stop’
button. Carefully snap and remove
the entry pillar and connect the
cable to the socket as shown.
8
If using a Digital Divert system, the cable plugs into the diverter using
the splitter box provided.
If using with a Divert product, refer to the Digital Divert instructions
opposite.
!
Prior to commissioning the iSys Digital remote control following the
procedure overleaf, please refer to the installation instructions
provided with the main iSys Digital product to complete the
installation of the Digital processor.
9
IF FITTING THIS PRODUCT WITH AN ISYS DIGITAL DIVERT
SHOWER SYSTE , PLEASE FOLLOW THE FITTING INSTRUCTIONS
BELOW.
!
F r use with iSys Digital Divert systems
iSys Digital rem te c ntr l installation instructions Page 10
10m Data Cable
10m Data
Cable
Splitter box
2m Data Cable
Wiring diagram
Table des matières
Autres manuels Aqualisa Télécommande
Aqualisa
Aqualisa Visage Manuel utilisateur
Aqualisa
Aqualisa QUARTZ DIGITAL SERIES Manuel utilisateur
Aqualisa
Aqualisa Quartz QZ.B3.WR.05 Manuel utilisateur
Aqualisa
Aqualisa Optic Q WR.BL.CP.20 Mode d’emploi
Aqualisa
Aqualisa AQLS Manuel utilisateur
Aqualisa
Aqualisa Quartz Digital QZD.B3.DS.14 Manuel utilisateur
Aqualisa
Aqualisa ilux Manuel utilisateur
Manuels Télécommande populaires d'autres marques
Panasonic
Panasonic EUR7622KB0 Manuel utilisateur
Bang & Olufsen
Bang & Olufsen Beo4 Manuel utilisateur
Sunwave Tech.
Sunwave Tech. RemoteComm SRC-7000 Manuel utilisateur
Multiplex
Multiplex PROFI TX 9 Manuel utilisateur
One Remote
One Remote RMB4 Manuel utilisateur
FUTABA
FUTABA 9ZAP - PART2 Manuel utilisateur
