Aqua PRO PRO100120 Manuel utilisateur

www.aquaprosystems.com

877.278.2797

LIMITED WARRANTY

For one (1) year from the date of purchase, Wayne Water Systems, d/b/a AquaPRO Systems (“AquaPRO”) will repair or

replace, at its option, for the original owner any parts of its Blower (“Product”) which are found upon examination by

AquaPRO to be defective in materials or workmanship. This Limited Warranty covers labor for a period of one (1) year for

Product sold and installed in the United States (does NOT cover service labor for removal and reinstallation of the blower).

Please call AquaPRO at 1-877-278-2797 for instructions. Be prepared to provide the model number and serial number when

exercising this limited warranty. Purchaser must pay all transportation charges on Products or parts submitted for repair or

replacement. All non-warranty service charges are the responsibility of the original owner. Failure to pay for non-warranty

service charges will void this Limited Warranty. This Limited Warranty does not cover Products that have been damaged as a

result of accident, abuse, misuse, neglect, improper installation, improper maintenance or failure to operate in accordance

with AquaPRO's written instructions. All maintenance and service must be performed by service agents approved by

AquaPRO. Any unauthorized alteration or repairs will void this Limited Warranty.

THERE IS NO OTHER EXPRESS WARRANTY. IMPLIED WARRANTIES, INCLUDING THOSE OF MERCHANTABILITY AND

FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED TO ONE (1) YEAR FROM THE DATE OF PURCHASE. THIS IS THE

EXCLUSIVE REMEDY AND ANY LIABILITY FOR ANY AND ALL INDIRECT OR CONSEQUENTIAL DAMAGES OR

EXPENSES WHATSOEVER IS EXCLUDED.

Some states do not allow limitations on how long an implied warranty lasts, or do not allow the exclusions or limitations of

incidental or consequential damages, so the above limitations might not apply to you. This limited warranty gives you

specific legal rights, and you may also have other legal rights which vary from state to state. In no event, whether as a result

of breach of contract warranty, tort (including negligence) or otherwise, shall AquaPRO or its suppliers be liable for any

special, consequential, incidental or penal damages including, but not limited to loss of profit or revenues, loss of use of the

products or any associated equipment, damage to associated equipment, cost of capital, cost of substitute products, facilities,

services or replacement power, downtime costs, or claims of buyer's customers for such damages. This Limited Warranty does

not include freight charges for equipment or component parts, to and from the factory, services such as maintenance or

inspection, repair or damage due to negligence such as freezing conditions, incorrect installation, nor acts of God. It also

does not include refrigerant or other expendable materials. The liability of AquaPRO Systems shall not exceed the repair or

replacement of defective parts under this Limited Warranty. This Limited Warranty also does not include unnecessary service

calls due to erroneous operational reports, external valve positions, or electrical service. If a non-warranty service call is

made, and the homeowner is unwilling to pay for the service call, this Limited Warranty will be voided. This Limited

Warranty is voided if the product is repaired or altered by any persons or agencies other than those authorized by AquaPRO

Systems. This Limited warranty applies only within the continental USA. For warranty outside the continental USA, contact

AquaPRO Systems.

You MUST retain your purchase receipt along with this form. In the event you need to exercise a warranty claim, you MUST

present a copy of the purchase receipt at the time of service. Please call AquaPRO Systems at 1-877-278-2797 for service or

return authorization and instructions.

DO NOT MAIL THIS FORM TO AQUAPRO SYSTEMS. Use this form only to maintain your records.

MODEL NO. _____________________ SERIAL NO. _____________________ INSTALLATION DATE __________________________

Operating Instructions and Parts Manual

SPA BLOWER

PRO1002403, PRO1502403, PRO2002403, PRO100120, PRO150120, PRO200120

101 Production Drive, Harrison, OH 45030 877.278.2797 fax 888.610.3839

[email protected] www.aquaprosystems.com

OWNER'S MANUAL

www.aquaprosystems.com 877.278.2797

1 Conduit Cover Plate, Gasket, 2 Screws, and Wiring Diagram (Kit) 81008-001 1

2 Blower Housing with Foam Inserts (Kit) 81006-001 1

3 Bracket 28569-001 1

4 Gear Clamp 67111-001 2

5 Motor 1

1 hp 120v 81000-001

1 hp 240v 81003-001

1-1/2 hp 120v 81001-001

1-1/2 hp 240v 81004-001

2 hp 120v 81002-001

2 hp 240v 81005-001

6 Sleeve 15497 1

7 Discharge Housing 28555-001 1

8 8-16 x 3/4 inch Plastite Screw 67007-001 8

9 Check Valve 10116-001 1

Ref. No. Description Parts Number QTY.

For Replacement Parts, call 1-877-278-2797

Replacement Parts List

Please provide following information:

- Model number

- Serial number (if any)

- Part descriptions and number as shown in parts list

PRO1002403, PRO1502403, PRO2002403,

PRO100120, PRO150120, and PRO200120

Address parts correspondence to:

AquaPRO®Systems

Attn: Customer Service

101 Production Drive

Harrison, OH 45030 U.S.A.

THIS PAGE INTENTIONALLY LEFT BLANK.

www.aquaprosystems.com

877.278.2797

Operating Instructions and Parts Manual

1. Check electrical connections and fuse

box / control panel

2. Disconnect power then check for

restrictions or blockage in air discharge

line

3. Replace motor

4. It is possible that if the blower is started

and stopped repeatedly in a short time

period, the thermal overload could

interrupt the circuit. Allow the unit to

cool and disconnect power. Restart after

5 - 15 minutes (depending on warmth

of ambient conditions).

1. Disconnect power then check for debris

or foreign object lodged in blower

motor

2. Replace motor

3. Verify voltage is correct for blower

1. Check electrical connections

Verify voltage is correct for blower

2. Install additional blowers, or reduce

piping restrictions

3. Re-orient check valve

1. Check for debris or foreign object

lodged in discharge line

2. Re-orient check valve

1. Check blower voltage requirements,

make certain line voltage is correct

2. Verify correct wire gage is being used

Blower will not

start

Blower hums but

will not run

Blower runs but

delivers little air

Internal blower

overload trips

Blower runs too

slow

1. Power Off

2. Internal blower

overload trips

3. Brushes worn out

4. Nuisance trips

1. Rotor locked

2. Brushes worn out

3. Wrong voltage

1. Low voltage

2. Blower too small for

application

3. Check valve installed

incorrectly

1. Blocked or restricted

air line

2. Check valve installed

incorrectly

1. Incorrect line voltage

2. Incorrect wire size

Symptom Possible Cause(s) Corrective Action(s) Safety Alert

Troubleshooting Chart - All repairs must be completed by licensed or certified professionals.

Disconnect power

BEFORE taking any

corrective action(s)

Disconnect power

BEFORE taking any

corrective action(s)

Disconnect power

BEFORE taking any

corrective action(s)

Disconnect power

BEFORE taking any

corrective action(s)

Disconnect power

BEFORE taking any

corrective action(s)

Please read and save these instructions. Read carefully before attempting to assemble, install, operate or maintain the product described.

Protect yourself and others by observing all safety information. Failure to comply with instructions could result in personal injury and/or

property damage! Retain instructions for future reference.

Description

The Air Blower is designed for outdoor

spa applications. It is designed for low

noise and a high air flow rate. The unit

is UL listed and the motor is protected

with a resetting thermal overload

device. The blower is designed for

permanent electrical connections.

The box contains the following:

• Blower

• Mounting Bracket

• UL Approved Check Valve

• Conduit Cover Plate, Gasket, and

Screws

• Instruction Manual

Unpacking/Unit Inspection

After unpacking the blower, carefully

inspect for any damage that may have

occurred during transit. Check for

loose, missing or damaged parts.

DAMAGE TO THE UNIT DURING

TRANSPORTATION IS NOT THE

RESPONSIBILITY OF THE

MANUFACTURER.

Important Safety

Instructions

When installing and using this

electrical equipment, basic safety

precautions should always be

followed.

READ AND FOLLOW ALL

INSTRUCTIONS.

Safety Guidelines

This manual contains information that

is very important to know and

understand. This information is

provided for SAFETY and to PREVENT

EQUIPMENT PROBLEMS. To help

recognize this information, observe

the following symbols:

Danger indicates

an imminently

hazardous situation which, if not

avoided, will result in death or serious

injury.

Operating Instructions and Parts Manual

Warning indicates

a potentially

hazardous situation which, if not

avoided, COULD result in death or

serious injury.

Caution indicates

a potentially

hazardous situation which, if not

avoided, MAY result in minor or

moderate injury.

Notice indicates

important

information, that if not followed, may

cause damage to equipment.

General Safety

Information

CALIFORNIA PROPOSITION 65

This product or its

power cord may

contain chemicals, including lead,

known to the State of California to

cause cancer and birth defects or other

reproductive harm. Wash hands after

handling.

GENERAL

To reduce the risk

of injury, do not

allow children to use this product

unless they are closely supervised at all

times.

Install blower no

less than 1 foot

(305 mm) above the maximum water

level to prevent water from contacting

electrical equipment. Install in

accordance with the installation

instructions.

Blower is designed

for outdoor use.

Install blower at least two feet above

the ground in an area free of debris,

chemicals, or sprinklers.

ELECTRICAL

Disconnect power before

attempting to install, service,

relocate or perform any

maintenance. Tag and disconnect

power and lock the fuse box / control

panel to prevent unexpected

application of power.

Risk of

Electric

Shock. Install blower at least

5 feet (1.5 m) from pool / spa

water using nonmetallic

plumbing.

To reduce

the risk

of electrical shock, connect

the green colored wire inside

the electrical box to the

grounding terminal of your electrical

service or supply with a continuous

green insulated solid copper conductor

minimum No. 8 AWG (8.4 mm2) solid

copper conductor between this unit

and any metal equipment, metal

enclosures of electrical equipment,

metal water pipe, or conduit within 5

feet (1.5 m) of the unit.

SAVE THESE INSTRUCTIONS.

Installation

Guidelines

Failure to observe

installation

guidelines, could result in death or

serious injury.

See Figure 1 for recommended

installation diagram.

1. Install at least 5 feet (1.5 m) from

pool / spa water using nonmetallic

plumbing. Install blower no less

than 1 foot (305 mm) above the

maximum water level to prevent

water from contacting electrical

equipment. Install in accordance

with the installation instructions.

2. The check valve supplied with the

unit must be installed in a vertical

orientation above the water level

in an easily accessible location for

serviceability. Take care to orient

the check valve with the arrow

pointing in the direction of the air

flow inside the pipe.

3. Use a separate dedicated 2-inch

rigid PVC supply line from the

blower to the spa.

www.aquaprosystems.com 877.278.2797

REMINDER: Keep your dated proof of purchase for warranty purposes!

Attach it to this manual or file it for safekeeping.

PRO1002403, PRO1502403, PRO2002403,

PRO100120, PRO150120, and PRO200120

Installation

Guidelines (Continued)

Do not glue the

blower to the

supply line. Glue fumes can potentially

cause an explosion when the blower

starts. Install a 1/4” self-tapping screw

to secure the joint if necessary.

Do not install

blower below

water level. Blower must be at least

one foot above the maximum water

level.

4. Mount blower in a vertical position

using vertical rigid PVC pipe as

shown in Figure 1. For additional

support use supplied bracket as

shown in Figure 1. For warm

climates, try to locate the blower in

a shaded location.

If the blower is to

be installed more

than 25 ft from the spa, it will be

necessary to install a loop that is 1

foot above the water line and as close

to the spa as possible (See Figure 1).

A loop and a check

valve must be

installed at least one foot above the

water level when supercharging water

jets.

5. Verify plumbing is free of leaks

before adding water to spa.

6. Do NOT install adjustable jets.

Adjustable jets can cause excessive

back pressure within the unit.

7. Hydrotherapy jets naturally aerate

when installed correctly. Do not use

blower to supplement aeration

when jets have been installed

incorrectly.

Wiring Guidelines

Failure to observe

wiring instructions,

could result in death or serious injury.

All wiring

and electrical

connections must be performed by a

qualified electrician. Installations must

be in accordance with local and

national codes.

1. For electrical ratings, see product

decal.

2. Check the line voltage to make

certain it is correct for the blower

being used. Do not attempt to

connect 240 VAC to a 120-volt

blower; it will damage the blower

and void the warranty.

3. Refer to the National Electric Code

Guidelines for wire size and to

prevent electric shock.

4. Refer to the National Electric Code

Guidelines for proper selection of

wiring conduit and strain relief.

5. The blower field-wiring box is

designed for non-metallic electrical

tubing only. Refer to the National

Electric Code Guidelines for proper

selection of wiring, and strain

relief.

6. Be certain to connect the green

ground wire supplied with the

blower to the ground from

your electrical panel.

7. Connect remaining line wires

individually to the remaining wires

in the blower.

8. When wiring is complete carefully

install gasket and conduit cover

plate.

Overheating, short-

circuiting and fire

damage will result from inadequate

wiring.

www.aquaprosystems.com

Figure 1

877.278.2797

Operating Instructions and Parts Manual

Grade

Wall or post

Bracket

Rigid PVC pipe

Check valve

(location when

NOT using a

Hartford Loop)

Air flow

5 Foot minimum from water

(use non-metallic plumbing)

Orient blower

housing as shown

Conduit box and cover

Non-metallic

electrical tubing

24 inches above

surrounding

grade / 12 inch

minimum above

water

Mount using rigid PVC pipe. For additional support, use supplied bracket as shown.

Hartford Loop required if Blower is more

than 25 feet away from pool / spa

12 inch minimum

Alternate location for check valve if

Harford Loop is used

Blower Sizing

The number of holes in the seats and

floor of the spa can be used to

determine the size of the air blower

that will be required for your

application. See Chart 1 for

recommended blower size based on

the number and size of holes.

Water Jet

Applications

The blower can be used to boost the

output of hydrotherapy jets. A venturi

fitting is normally incorporated into

the jet design. The purpose of the

fitting is to allow air to mix with the

water in the jet. The venturi fittings

can be connected together and then

pressurized with air from the blower to

greatly increase the jet action.

www.aquaprosystems.com

New Spa

Applications

It is important to select a water pump

that will supply sufficient flow to the

jets. Consult with the jet manufacturer

for assistance in selecting a pump or

pumps that will accommodate the

number of jets desired in the spa.

Improper sizing can cause overheating

of the pump and blower.

Choose the correct size blower based

on the number of water jets in your

spa (see Chart 1). See the chart below.

Refer to the installation guidelines for

additional details.

Winterizing

The blower is designed for outdoor

use. There are no special off-season

requirements for the blower. In some

spa systems it is possible to protect

discharge lines from freezing by

operating the blower for several

minutes with the spa drained. The

airflow can be used to purge water

from the air lines.

877.278.2797

Chart 1

Notes

PRO1002403, PRO1502403, PRO2002403,

PRO100120, PRO150120, and PRO200120

Recommended Number of Holes

at the Following Hole Diameters

1/8 Inch 3/16 Inch 1/4 Inch

76 35 20

100 46 26

150 68 38

Total Hole Area

Square Inches

1.0

1.4

1.8

Blower

Model

PRO100120, PRO1002403

PRO150120, PRO1502403

PRO200120, PRO2002403

Number of

Water Jets

4 to 9

9 to 13

14 or more

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Aqua PRO Ventilateur

Aqua PRO

Aqua PRO PRO1002403 Manuel utilisateur

Manuels Ventilateur populaires d'autres marques

Weed Eater

Weed Eater VS2000BV Manuel utilisateur

KRAUSMANN

KRAUSMANN U37020-00 Manuel utilisateur

Bosch

Bosch ALB 36 LI Manuel utilisateur

Cub Cadet

Cub Cadet HB425 Manuel utilisateur

GreenWorks Pro

GreenWorks Pro BLB482 Manuel utilisateur

ARIETE

ARIETE 2768 Manuel utilisateur

NuTone

NuTone 331H Manuel utilisateur

GÜDE

GÜDE GLB 200 18 Li-Ion Manuel utilisateur

I.VA.CO.

I.VA.CO. SC Series Mode d'emploi

DeWalt

DeWalt DCE100 Manuel utilisateur

Becker

Becker SV 7.330 Manuel utilisateur

Metabo

Metabo AG 18 Pro Manuel utilisateur

Desa

Desa GA3650TB Manuel utilisateur

Echo

Echo Power Blower PB-230LN Manuel utilisateur

Echo

Echo PB-413H Manuel utilisateur

Black & Decker

Black & Decker BV3100 Manuel utilisateur

Ryobi

Ryobi RY08570 Manuel utilisateur

Haaga

Haaga 355 Manuel utilisateur