Aqua Creek PRO SPA 60 Manuel utilisateur

PRO SPATM 60

PART NUMBER: F-007EXA

US PATENT NUMBER: D507,769 S

300 LB. MAXIMUM CAPACITY

MANDATORY – LEAVE THIS MANUAL WITH LIFT OWNER

AQUA CREEK PRODUCTS

9889 GARRY MORE LANE

MISSOULA, MT 59808

1-888-687-3552

FAX: 406-549-2602

AQUA CREEK, LLC 2013 FEB 2013

- WARNING-

IMPORTANT SAFETY INSTRUCTIONS

1. READ AND FOLLOW ALL INSTRUCTIONS. LIFT SAFETY CAN ONLY BE ENSURED IF THE

LIFT IS INSTALLED AND OPERATED PROPERLY – ACCORDING TO THESE INSTRUCTIONS.

2. TO REDUCE THE RISK OF INJURY, DO NOT PERMIT CHILDREN TO USE THIS PRODUCT

UNLESS THEY ARE CLOSELY SUPERVISED AT ALL TIMES.

3. DO NOT PERMIT CHILDREN TO PLAY ON OR AROUND THIS PRODUCT.

4. NEVER APPLY DIRECT WATER PRESSURE TO THE ELECTRONIC COMPONENTS.

5. SAVE A COPY OF THESE INSTRUCTIONS IN A SAFE AND EASILY ACCESSIBLE PLACE.

Accessible Environments, Inc.

Authorized National Dealer

For orders/questions, call:

(800) 643-5906

www.acessinc.com

ASSEMBLY INSTRUCTIONS

The lift arrives mostly assembled on a crate. Begin by locating all parts for your lift in the parts

lists below.

PARTS LIST

CRATE 1

1. PRO SPA 60 ASSEMBLY

ITEMS INCLUDED WITH PRO SPA 60 LIFT

1. (1) 24V BATTERY

2. (1) BATTERY CHARGER

3. (1) HAND CONTROLLER

4. (1) SEAT BELT

5. (1) HARDWARE BAG

TOOLS NEEDED: 9/16” Wrench (2)

3/4" Wrench Drill

Hammer Marker/Chalk

1 1/8" Masonry Bit Epoxy or Hydraulic Cement

1.) Locate the 24v battery and wall mount battery charger. Batteries arrive from the factory

partially charged. Charge the battery for 24 HOURS before initial use of the lift.

Determine the location that you want to position the wall mount charger (next to a 110v

AC outlet), and fasten it with the supplied screws. Plug in the charger to the outlet.

2.) Clip the battery to the charger and allow the battery to charge. When the battery is

correctly mounted to the charger, the CHARGE light will illuminate. When the battery

is fully charged, the CHARGE light will GO OFF.

3.) Go to the next section “PRO SPA 60 ASSEMBLY”.

HARDWARE BAG

ITEM # QTY. DESCRIPTION PART USE / LOCATION

1 3 4” DUAL THREADED ANCHOR ANCHOR

2 3 1/2” x 1-1/2” HEX HEAD BOLT S.S. STANDARD ANCHOR BOLT

3 3 1/2” FLAT WASHER S.S. ANCHOR BOLTS

4 1 3/8” x 1-3/4” HEX BOLT, S.S. CHAIR ACTUATOR

5 1 3/8” NYLOCK NUT CHAIR ACTUATOR

PRO SPA 60 ASSEMBLY

1. Remove tie-wraps and bubble packing from electric actuator.

2. Slide the chair arm up until the actuator bracket is about even with the actuator lug.

3. Align the holes in the actuator lug with the hole in the actuator bracket. Attach the

actuator to the actuator bracket using one (1) 3/8” x 1-1/4” shoulder bolt, one (1) 5/16”

flat washer and one (1) 5/16” nylock nut as shown in FIGURE 1. Tighten the nut until

snug.

PRO SPA 60 WIRING: Y-CONNECTOR

The Pro Spa 60 uses two electric actuators

to lift the seat and these actuators are

wired together using a special y-connector.

The y-connector is plugged into channel 1

of the control box.

When operating properly both electric

actuators will move at the same time. If

only one actuator moves at a time there

may be a problem with the y-connector or

the electric actuator. Always make sure the

plugs are fully seated in the control box.

ANCHOR INSTALLATION INSTRUCTIONS

Before installing the anchors, it is necessary to determine where you want to place the lift on

your deck. You will want to locate the lift as close to the outside wall of your pool/spa as

possible to ensure that the seat arm clears your spa/pool wall. As shown in figure 1 below, the

lift must be a minimum 3 ½ ” from the front anchor holes to the pool/spa wall. Also, you will

want to allow enough room for the seat arm to swing around away from the pool/spa. Refer to

the specifications for lift dimensions.

1.) The lift is shipped with 4” anchors. If you are installing the anchors and have not

received the lift, use the dimensions from figure 2 below to set the anchor locations.

Make a mark on the deck with a marker or chalk at each anchor location. If you have the

lift and have not installed the anchors, position the lift at the desired location and mark

the concrete at each anchor location.

2.) Using the 1 1/8” [30mm] masonry bit drill a hole in the concrete deck to a depth of 4”

[102mm] at each of the three anchor locations. The holes must be drilled plum, or the lift

bolts will not thread into the anchors. Once the holes have been drilled to the proper

depth, clean debris out of anchor holes.

3.) Check that the holes are deep enough by dropping a 4” anchor into the hole to make sure

it comes out flush with the deck surface. If not re-drill the hole/holes until they are flush.

4.) Fill each hole ½ full with expanding epoxy or hydraulic cement. Thread a 1-1/2” bolt into

each anchor and then insert the anchor into the hole, twisting as you go. Clean off any

excess epoxy from around the hole, and make sure not to get any epoxy on the ½”

threads.

FIGURE 2

INSTALLING THE LIFT

1.) Once the anchors have been installed, you can now install the lift. Position the lift over

the anchors as shown in figure 3.

2.) Using the supplied hardware, secure the lift to the deck as shown in figure 3.

3.) Attach the supplied safety belt to the chair by opening each end of the belt and looping

the ends through the slots on either side of the chair as shown in figure 3. The Velcro

ends can be adjusted to suit the users’ needs.

ADJUSTING SEAT ANGLE:

The angle of the seat arm is adjustable to provide

additional clearance from the spa wall. Adjust the

angle of the seat arm assembly by loosening the 3/8”

jam nut and adjusting the 3/8” bolt at the base of the

lifting plates (top of lifting arm). As shown in the

diagram to the right, tighten the bolt to increase

clearance, and loosen it to decrease the angle of the

seat arm. When the desired angle is achieved tighten

the jam nut to lock the angle.

OPERATING INSTRUCTIONS: PRO SPA TM 60

NOTE: CHECK ALL NUTS & BOLTS FOR TIGHTNESS BEFORE EACH USE

NOTE: CHECK DRIVE BELT FREQUENTLY TO PREVENT SLIPPAGE AND

PROLONG SYSTEM LIFE. (SEE BELOW “BELT TIGHTENING”)

Before attempting to transfer into the chair, check the battery warning light on the 24v battery. If

this light is illuminated, this means the battery is at a low charge.

DO NOT attempt to use the lift if the “low charge” indicator light is on. Remove the battery

from the lift and place it on the wall mount charger until the battery is fully charged before

resuming use of the lift.

If your lift is equipped with a pullout leg-rest it will be necessary to

have the leg-rest engaged in the extended position with the leg-rest

flipped up for pool/spa walls higher than 36”. For pool/spa walls

shorter than 36”, the leg-rest may be flipped up or down.

You may transfer to the chair from either side, by flipping up the

armrest on the preferred side to allow for easy lateral transfer. Once

you are in the chair, lower the flip-up arm back into its normal

position for operating the lift. If your lift is equipped with a leg-rest,

position your legs comfortably on the leg-rest. Secure the adjustable

lap belt around your waist so that the belt is snug, but not

uncomfortably tight.

You are now seated comfortably in the lift, and ready to move into the pool or spa. Before you

begin the lift’s operating cycle, take a visual check of the deck area and pool/spa area to ensure a

clear operating path.

Now take the handheld controller and press the “up” arrow at the top of the controller. The lift

should start to move up smoothly. Continue holding the “up” arrow button until you have

cleared the pool/spa wall. Once the user has cleared the pool/spa wall vertically, press either of

the lower buttons on the handheld controller to rotate over the pool/spa wall. The PRO SPATM is

equipped with a push-button rotate mechanism that allows the lift to rotate 360clockwise, or

counter-clockwise. By pressing either of the lower “rotate” buttons, the user may rotate in and

out of the pool/spa in either direction.

WARNING! THE ROTATE MECHANISM ON THE LIFT IS DESIGNED TO ROTATE

THE LIFT WITH A 400 LB. MAXIMUM WEIGHT CAPACITY. IF THE CHAIR IS

IMPEDED BY AN OBJECT WHILE ROTATING, THE LIFT MAY BEGIN TO CLICK

OR POP. THIS MEANS THAT THERE IS TOO MUCH RESISTANCE ON THE LIFT.

PROMPTLY STOP THE ROTATION AND REMOVE THE RESISTANCE. THE LIFT

SHOULD NOW CONTINUE TO ROTATE SMOOTHLY.

Once the user is positioned over the pool/spa, simply press the “down” arrow to lower the user

into the pool/spa. Release the “down arrow” button once the user has reached the desired depth

in the pool/spa. Now release the lap belt by tugging gently on the top flap of the lap belt. Lift up

the flip-up arm-rest and exit the seat into the pool/spa. The handheld controller can simply rest

on the seat arm when the user is not using the lift. If desired, the user can send the lift chair up

and out of the pool/spa so that the chair is not a hindrance while he or she is in the pool/spa. If

this is desired, the controller must be kept in an accessible location in order to call the lift back.

WARNING: DO NOT ROTATE THE LIFT WHILE IT IS SUBMERGED IN THE

POOL/SPA. THIS MAY RESULT IN INJURY.

INSTALL 24V BATTERY & HANDSET

Locate the 24V Battery, the Battery Charging unit and the Handset

Control. Charge the battery for 24 hours (see page 11) then install it

on the bracket above the Control Box. Plug the Handset Control into

the Control Box as shown in the photos to the left. Press firmly to

make sure the plug is fully seated as shown below.

THE LIFT WILL NOT FUNCTION IF THE HANDSET PLUG IS

NOT FULLY SEATED OR IF THE BATTERY IS NOT

PROPERLY ALIGNED.

NOT SEATED SEATED

LIFT OPERATION:

Before operating the PRO SPA 60TM lift for the first time, the user or operator should become

familiar with the Handset Control and its functions. The figure to the left gives a quick

explanation of the four buttons and their function. For example, to move the lift UP, press the

top left button with the ▲ symbol and hold it down until the lift has reached its desired height

and then release the button. The other buttons work in a similar fashion. In all cases, releasing

the button will cause the lift to stop moving.

TO MOVE UP PRESS AND HOLD THE

▲ BUTTON. TO STOP MOVING UP

RELEASE THE BUTTON.

TO MOVE DOWN PRESS AND HOLD

THE ▼ BUTTON. TO STOP MOVING

DOWN RELEASE THE BUTTON.

TO MOVE LEFT PRESS AND HOLD

THE◄►BUTTON. TO STOP MOVING

LEFT RELEASE THE BUTTON.

TO MOVE RIGHT PRESS AND HOLD

THE►◄BUTTON. TO STOP MOVING

RIGHT RELEASE THE BUTTON.

CARE OF YOUR LIFT

Routine cleaning is an absolute necessity to ensure the integrity of the lift. Note that the Aqua Creek Pool Lift should

not be stored in a pump room or in a storage room where pool chemicals are kept. Storing the lift near pool chemicals

may cause rusting and other damage to occur. Your Aqua Creek stainless steel lift is powder coated to protect the

stainless steel from rusting. Most rusting will occur at weld points, crevices, under gaskets, rivets or bolt heads.

The choice of a proper cleaning product is up to the consumer and there are many to choose from. Depending on the

type of cleaning and the degree of contamination (rusting), some products are better than others. For routine cleaning

the products most recommended are gentle soaps or detergents or dilute mixtures of ammonia. For stubborn spots and

stains try using soft scrub with some brisk rubbing.

DO NOT USE POOL WATER TO CLEAN USE ONLY FRESH WATER

If the lift is used DAILY make sure to wash the lift at the end of the day. Wash the lift off using a mild soap and a soft

cloth. Make sure to pay special attention to weld points and crevices. Do not use a bristled brush or steel wool to clean

the lift. Check that the lift is working properly and then place the battery on the charger. It is recommended that the

battery be charged after every day of use.

If the lift is used WEEKLY follow the same steps as above. Also be sure to check all of the contact points (terminals)

for damage or corrosion. If you notice corrosion gently clean the terminals. To clean corrosion from the terminals use a

q-tip and some rubbing alcohol. If the corrosion is particularly stubborn try using a 3M scotch brite pad, but be careful

not to damage the terminals. Apply dielectric grease to the terminals after cleaning them. This will help to prevent

further corrosion. Do not leave the battery on the lift. Always store the battery on the charger whenever the lift is not

being used.

If the lift is used MONTHLY follow the same steps as above. Also check the nuts and bolts to make sure they are

securely fastened (this is always a good idea, no matter how often or infrequently the lift is used). Also make sure to

store the battery on the charger and not on the lift. Leaving the battery on the lift for extended periods will significantly

shorten the battery’s lifespan.

If the lift is being STORED for an extended period of time follow all of the steps above. Check for rusting at all

crevice and weld points. If you notice rusting spray some WD-40 on the affected area and take a 3M scotch brite pad

and rub briskly. Afterwards be sure to wash and rinse the lift again with soap and water. When storing the lift make

sure it is in a dry area and covered. DO NOT STORE in or around pool chemicals.

SAFETY & MAINTENANCE INSTRUCTIONS

1. Do not play on or around this lift

2. Check the PRO SPA LiftTM before each use to assure there are no worn parts and

that all hardware is properly tightened. If there are any worn parts, replace them

BEFORE using the PRO SPA LiftTM. You can call our customer service at 1-888-

687-3552 to order any parts.

3. Aqua Creek Products, LLC shall be grounded per local codes.

4. At least ONCE A WEEK, thePRO SPA LiftTM must be cleaned with fresh water.

Do not spray the PRO SPA LiftTM 24v battery unit directly with any pressure.

Wipe all surfaces clean with a damp, non-abrasive cloth. When cleaning the

PRO SPA LiftTM , use non-abrasive soap and water. Avoid harsh chemicals and

disinfectants.

5. Always read the label instructions on any cleaner carefully before applying it to a

surface.

6. The WARNING & INTENDED USE labels on the PRO SPA LiftTM need to be

maintained in readable fashion. If they become unreadable or faded, please

replace the immediately. Replacement labels are available from AQUA CREEK

PRODUCTS LLC. 1

888

687

3552.

BELT TIGHTENING:

The drive belt should be checked periodically to

ensure it is tight, to ensure that the lift rotates

properly. To check the drive belt remove the motor

shroud (see parts section) and check that the drive

belt is snug and does not slip when the lift is rotated.

If the belt slips or does not seem tight, tighten the

belt using a pry-bar and a combination wrench as

shown. Loosen all four bolts, use the pry-bar to

tighten belt and hold it tight while retightening the

bolts.

Table des matières

Autres manuels Aqua Creek Système de levage

Aqua Creek

Aqua Creek Revolution Deep F-702RLNA-DD-04 Manuel utilisateur

Aqua Creek

Aqua Creek F-702RLSDD Manuel utilisateur

Aqua Creek

Aqua Creek RANGER-AT F-409RPL-AT1 Manuel utilisateur

Aqua Creek

Aqua Creek Ambassador F-PPXRD-NA-02 Manuel utilisateur

Aqua Creek

Aqua Creek F-105LAR Manuel utilisateur

Aqua Creek

Aqua Creek Pro Pool-AT Manuel utilisateur

Aqua Creek

Aqua Creek PATRIOT PORTABLE LIFT Manuel utilisateur

Aqua Creek

Aqua Creek F-043SCH Manuel utilisateur

Aqua Creek

Aqua Creek Patriot-AT F-12PPL-HD-AT2 Manuel utilisateur

Aqua Creek

Aqua Creek Revolution Manuel utilisateur

Aqua Creek

Aqua Creek F-004PLB-23-AT1 Manuel utilisateur

Aqua Creek

Aqua Creek F-03EZPL Manuel utilisateur

Aqua Creek

Aqua Creek PRO POOL-AT F-004PLB-DD12-AT1 Manuel utilisateur

Aqua Creek

Aqua Creek Scout 2 Manuel utilisateur

Aqua Creek

Aqua Creek PORTABLE PRO POOL-AT LIFT Manuel utilisateur

Aqua Creek

Aqua Creek Ambassador Manuel utilisateur

Aqua Creek

Aqua Creek F-600TLNA Manuel utilisateur

Aqua Creek

Aqua Creek Ambassador Pool Lift Manuel utilisateur

Manuels Système de levage populaires d'autres marques

morse

morse 82H-124 Manuel utilisateur

Braun

Braun NL955 Series Manuel utilisateur

haacon

haacon 1889.10 Manuel utilisateur

Protekt

Protekt AT 252 Manuel utilisateur

R. Beck Maschinenbau

R. Beck Maschinenbau HS 600 Manuel utilisateur

Nova Technology International, LLC

Nova Technology International, LLC NAS Series Manuel utilisateur

Genie

Genie Z-60/34 Manuel utilisateur

Screen Technics

Screen Technics INTERFIT Vertical Up Lift Manuel utilisateur

Mortuary Lift

Mortuary Lift ULTIMATE 1000 Manuel utilisateur

Custom Equipment

Custom Equipment Hy-Brid 3 Series Manuel de programmation

Custom Equipment

Custom Equipment Hy-Brid Lifts 2 Series Manuel de programmation

Hy-Brid Lifts

Hy-Brid Lifts HB-P3.6 Manuel de programmation

BERG

BERG BeNomic EasyLeaf Manuel utilisateur

Powermate

Powermate LiftGate LG-3 Manuel utilisateur

Snorkel

Snorkel TM12 Series Manuel utilisateur

Terberg

Terberg OMNIDEKA Manuel utilisateur

Harmar Mobility

Harmar Mobility AL625 Mode d'emploi

Rotary

Rotary SPO16 Manuel utilisateur