APW Wyott EGD-48 Manuel utilisateur

INSTALLATION AND OPERATING INSTRUCTIONS

Electric Griddles, Drop-In Style

P/N 88060-50 9/05

IMPORTANT FOR FUTURE REFERENCE

Please complete this information and retain this manual for the life of the equipment. For

Warranty Service and/orParts, thisinformation is required.

ModelNumber Serial Number DatePurchased

WARNING:

Improper installation, operation, service or maintenance can cause property

damage, injury or death. Read and understand these instructions thoroughly before

positioning, installing, maintaining or servicing this equipment.

Models: EGD-48 & EGD-72

APW WYOTT Foodservice Equipment Company

P.O. Box 1829

Cheyenne, WY 82003

+1 (307) 634-5801 Phone +1 (800) 752-0863 Toll Free

+1(307) 637-8071 Fax www.apwwyott.com

WARNING:

For your safety do not store or use gasoline or other flammable vapors or liquids in the

vicinity of this or any other appliance. Keep the area free and clear of combustibles. (See ANZI

Z83.14B,1991)

CONTENTS

General Information

Safety Precautions

Specifications & Dimensions

General Installation Instructions

Electrical Data

Owners Information

Care & Cleaning

Servicing

Wiring Diagrams

Replacement Parts List

Warranty

GENERAL INFORMATION

THIS MANUAL SHOULD BE RETAINED FOR FUTURE REFERENCE

IMMEDIATELY INSPECT FOR SHIPPING DAMAGE

All containers should be examined for damage before and during unloading. The freight carrier has

assumed responsibility for its safe transit and delivery. If equipment is received damaged, either apparent

or concealed, a claim mustbe made with the delivering carrier.

A) Apparent damage or loss must be noted on the freight bill at the time of delivery. It must then be signed

by the carrier representative (Driver). If this is not done, the carrier may refuse the claim. The carrier can

supplythe necessaryforms.

B) Concealed damage or loss if not apparent until after equipment is uncrated, a request for inspection

must be made to the carrier within 15 days. The carrier should arrange an inspection. Be certain to hold all

contents and packaging material.

Installation and start-up should be performed by a qualified installer who thoroughly read, understands and

followsthese instructions.

If you have questions concerning the installation, operation, maintenance or service of this product, write

Technical Service Department APW/Wyott Foodservice Equipment Company, P.O. Box 1829, Cheyenne,

WY82003.

Congratulations on your purchase of APW Wyott commercial cooking or refrigeration equipment.

takes pride in the design and quality of our products. When used as intended and with proper care

and maintenance, you will experience years of reliable operation from this equipment. To ensure best

results, it is important that you read and followthe instructions in thismanual carefully.

The data plate is located on the front panel.

APW

Wyott

LOCATION OF DATA PLATE

CAUTION:

These models are designed, built, and sold for commercial use. If these models are

positioned so the general public can use the equipment, make sure that cautions, warnings, and

operating instructions are clearly posted near each unit so that anyone using the equipment will

useit correctlyandnotinjurethemselvesorharmtheequipment.

WARNING:

Improper installation, operation, service or maintenance can cause property damage,

injury or death. Read and understand these instructions thoroughly before positioning, installing,

maintainingorservicingthisequipment.

WARNING:

Install per the spacing requirements listed in the installation section of this manual. We

strongly recommend having a competent professional install the equipment.A licensed electrician

should make the electrical connections and connect power to the unit. Local codes should always

be used when connecting these units to electrical power. In the absence of local codes, use the

latestversionof the NationalElectricalCode.

WARNING:

For your safety do not store or use gasoline or other flammable vapors or liquids in the

vicinity of this or any other appliance. Keep the area free and clear of combustibles. (See ANZI

Z83.14B,1991)

NOTICE:

Instructions to be followed if anyone smells gas should be posted in a prominent place.

Thesemaybe obtainedfromthegassupplier.

WARNING:

This product is intended for commercial use only. Not for household use Retain this

manualfor futurereferenceOvenmust be kept clear of combustiblesatalltimes

WARNING: -

SHOCKHAZARD

Donotopenanypanelsthat requiretheuseof tools.

SAFETY PRECAUTIONS

Before installing and operating this equipment be sure everyone involved in its operation is fully trained and

is aware of all precautions. Accidents and problems can result by a failure to follow fundamental rules and

precautions.

The following words and symbols, found in this manual, alert you to hazards to the operator, service

personnel or the equipment.The words are defined as follows.

!WARNING:

This symbol refers to a potential hazard or unsafe practice, which could result

in serious injury or death.

!DANGER:

This symbol warns of imminent hazard which will result in serious injury or

death.

!CAUTION:

This symbol refers to a potential hazard or unsafe practice, which may result in

minor or moderate injuryor product or property damage.

!NOTICE:

This symbol refers to information that needs special attention or must be fully

understoodeven thoughnot dangerous.

SPECIFICATIONS AND DIMENSIONS

Model Width Depth Height No. of kW Per Total

in. (mm) in. (mm) in. (mm) Elements Element kW

Griddle Surface Dimensions: Model Width in./cm Depth in./cm

General Installation Instructions:

Caution: DO NOT

NOTICE:

EGD-48 49.0/125 29.5/75 0.31/0.8 8 2.7 21.6

EGD-72 72.0/191 29.5/75 0.31/0.8 12 2.7 32.4

EGD-72 72.0/191 32.5/83 0.31/0.8 12 2.7 32.4

Double Trough

EGD-48 46.5/119 23.94/61

EGD-72 69.5/177 23.94/61

use an open flame to check for leaks. Check all gas piping for leaks with a

soapand water solutionbeforeoperating unit.

THE UNIT, WHEN INSTALLED, MUST BE ELECTRICALLY GROUNDED IN ACCORDANCE

WITH LOCAL CODES, OR IN THE ABSENCE OF LOCAL CODES, WITH THE NATIONAL ELECTRICAL

CODE,ANSI/NFPA70,LATESTEDITION.

CANADIAN INSTALLATION MUST COMPLY WITH THE CANADIAN ELECTRICAL CODE, CSA C22.2,

ASAPPLICABLE.

Local codes regarding installation vary greatly from one area to another. The National Fire

Protection Association, Inc., states in its NFPA 96 latest edition that local codes are "authority having

jurisdiction" when it comes to requirements for installation of equipment. Therefore, installations should

comply with all local codes.

GENERAL INSTALLATION INSTRUCTIONS

With all the large holes cut out, the smaller control panels drilled, and the stiffening angle welded into place

the fixture is now ready to receivethe griddle.

1. The manufacturer furnishes a gasket or seal that must be placed around the perimeter of the hole in

the top as shown in Fig. 4. This gasket may be temporarily held in place with tape. Do not place the

staple securingthe gasket ends on or neara corner.

2. A number of clamps, such as the one shown in Fig. 4, appear at intervals along the perimeter. Pull

clamps outward so the griddle frame clearsthem when it is droppedinto place.

3. Drop the griddle into position by lowering it into the fixture top hole. Make sure the thermostat

capillaries are not kinked or pinched when setting the griddle in place. With the griddle in place, the

gasket or seal becomes compressed.See Fig. 5.

4. Slide the clamp inward so it engages the upper part of the protruding angle from the griddle frame.

See Fig. 6. Slide the clamp sideways so the notch on it locks against the reinforcement angle. This

prevents the clamp from sliding out.

5. Tighten the clamp screws against the angle as shown in Figure 6.This tightening forces the clamps

to press down on the griddle body frame extension.The griddle top is now drawn close to the fixture

top, compressing the gasket and forming an effective grease guard. Tighten at least one screw on

each side before tighteningall screws. Do not exceed 60 in/lbtorque when tighteningbolts.

6. Slide the tray slide (grease drawer receptacle) through the cutout hole on the apron or front of the

fixture, resting it on the two"U" braces.

7. Mount the thermostats to the control panel and make the pilot light connections per the

accompanying wire diagram. Before making any electrical connections, check nameplate voltage

(located on tray slide undergrease drawer) to ensureit matches voltage being applied.

8. Set the control panel in place and screw it to the apron using the ½ inchlong thread forming screws.

9. Pull the tray slide against theback of the control panel and secure it with the appropriate screws.

Figure 3

Figure 4

Figure 5

Figure 6

Electrical Connections

Terminal Box Location:

Loading:

Fusing:

Grounding:

U.L. CONDITIONS OF ACCEPTABILITY:

NOTES: .

The terminal boxes can be located at either the left front or right rear of the griddle. When shipped

from the factory the device has the terminal box attached in the left front position. The box can be

relocated to the alternateposition by removing twoscrews.

Electrical loadings of thegriddles covered by this instructionare tabulated below.

Griddle is not fused and mustbe connected to a properly fusedcircuit.

Griddle must be grounded in accordance with the National Electrical Code and applicable local

codes.

1. This equipment must be installed in an all metal fixture of steel or stainless steel construction,

.078 inch thick minimum for the top and supportingframe. Side enclosure to be at least 22 MSG

minimumthickness.

2. Aremovable bottom enclosure must be provided under each drop-in unit and be made of metal

construction of at least 22 MSG minimum. If ventilating openings are provided in the bottom

enclosure, they must not allow the entrance of ¾ inch diameter rod nor be located directly

belowuninsulated liveterminals.

3. Minimum spacing between griddle top edge and adjacent items should be: fixture back wall 1 ¾

inch, fixture side enclosure1 inch, front controlpanel 7/8inch, other drop-in devices1 inch.

4. Controls shall be mountedon the front vertical surfaceof the fixture.

5. For supply connections,use wire suitable for at least 90° C (194° F).

1. Griddle can be mounted with the trough in the front or rear, dimensions shown are for front

trough mounting. Forrear trough mounting,this dimension mustbe between 7/8 and 2 inches.

2. Table top reinforcementandgasket furnishedwith thegriddle.

3. At the factory, the electrical connection box was installed in the front position. The connection

box can be moved to the rear locationshown.

IMPORTANT:

1. Any dimension smaller than the minimum or larger than the maximum shown in the table will

require corresponding changes to the grease chute by the fabricator by adding an extension to

preventthe greasefrom spillinginto the cabinet.

2. Any dimensions smaller than minimum given will require additional panels or sides and back to

facilitateservicing.

3. The minimum dimension from the back of the control panel to the front of the griddle top is 7/8 inch

regardless of the shape of thebullnose or table overhang.

4. Griddles are shipped from the factory with dimension "D" at 7 7/16 inch. Moveable braces permit

the fabricator to easily varythis dimension up to 1 0 7/16 inchesin increments of ¾ inch.

5. The minimum space between adjacent griddles must be 1 5/8 inch and between any other

combination of drop in cookingequipment mustbe 1 inch.

6. Electrical wiring crossingthe tray slide is to be placed underthe tray slide and not aboveit.

7. The installer or servicer must put the electrical wiring near the control panel inside the wire guide

before attaching the control panel to thefixture front.

IMPORTANT STEPS IN INSTALLATION:

1. Griddle position to be no closer than 7/8 inch from componentframe edge and control panel.

2. Install the gasket between the griddle top and the table top before clamping. Exercise caution so

that the griddle top does not pinchor damage the gasket.

ELECTRICAL DATA

- -

- - -

OWNER'S INFORMATION

Cleaning the Griddle After Uncrating:

The Controls:

Seasoning the Griddle Surface:

Operating Instructions:

Before using for the first time, be sure to remove the factory-applied rust preventative compound.

Add a mild detergent to hot water and wash the griddle well. Rinse with a clean, damp cloth and

wipedry.

Turning the dial knob (recessed in the front control panel) controls the heat of the griddle surface.

When at least one control is turned on, a signal light in the upper left-hand corner of the control panel

will glow continuously. Thus, the operatorknows at a glance whether or not the griddle is energized.

Separate signal light cycles with each control. Whenever the thermostat calls for heat, the signal

light associated with it will be on. Each thermostat controls twelve inches of griddle surface width.

Thermostat temperature range is 200°- 450°F+/- 10°F.

After thorough cleaning, the griddle is ready for seasoning. Preheat to 400°F. When the dialed

temperature is reachedas indicated by the signal lights goingoff, spread a light film of cooking oil or

fat over the entire surface of the griddle. In two minutes,wipe the griddle clean of excess oil. Repeat

this operation.The griddle is now ready for use.

1. Preheat griddle (preheat time, 77°F - 350°F, approximately 8 minutes). Set the thermostat dials at

the correct griddling temperature for the food to be cooked.Ared light will flash on automatically for

each section of the griddle when the dial is set and will flash off when the section has reached the

dialed temperature. (The signal light will flash on and off during the cooking operation to show that

correct temperatureis being maintained.) You are now readyto load the griddle.

-48 -72MODEL EGD MODEL EGD BOTH MODELS

CAPACITIES QTY APPROX QTY APPROX COOKING

PER HOURLY PER HOURLY TIME

LOAD PRODUCTION LOAD PRODUCTION & TEMP

MEATS

-oz. steaks, )

-oz. steaks, 1" thick)

-oz. slices, 3/8 thick)

OTHER FOODS

Fried

30 Ibs.

70 Ibs 40 Ibs

93 Ibs

1000+

1470+

2. Load Griddle. After preheating, load griddle and cook according to recipe. Turn foods halfway

through cooking timeunless otherwise specifiedin recipe.

Economy Hint:

Turn griddle OFF (or to lowestthermostat setting) during idle periods.

CARE & CLEANING

1. IMPORTANT:At the end of each days operation,turn all temperature controlsto OFF.

2. After each cooking load, scrape the griddle surface with scraper or rigid spatula to remove excess

fat and food particles. ONCE A DAY, or whenever necessary, thoroughly clean and wipe out the

grease trough.As necessary during use, wipe out accumulated material to provide good drainage.

Remove grease drawer, empty and wash. In general, soap and waterwith the aid of a sponge or soft

cloth will clean the drawer thoroughly. Wipe clean with a damp cloth and dry. Clean control panel

with a damp cloth and dry.

3. EACH WEEK, or whenever necessary, clean griddle thoroughly. If desired, use a pumice or griddle

stone over surface. Rub with the grain of the metal while still warm. Avoid steel wool! After each

thorough cleaning, the cooking surface must be reseasoned. To remove control knobs for cleaning,

pull straight out. Wash in soapy water. Rinse, dry and replace on shaft.

SERVICING

Your griddle is covered by a one-year written warranty on parts and labor. If this device should require

service, call your local commercial equipment dealer or authorized service station. The nameplate

indicating the pertinent electrical data of the griddle is located in the front of the grease drawer receptacle

and can be seen readily whenthe drawer is removed.

EGD-48 WIRING DIAGRAM

EGD-72 WIRING DIAGRAM

ALTERNATE WIRING

FOR TWO

POWER SUPPLIES

Griddle

(Bottom View)

Thermostat

Bulb

PARTS LIST DROP-IN ELECTRIC GRIDDLES, EGD-48 & EGD-72

ITEM PART NUMBER DESCRIPTION

14397-25

14397-26

642567 -01

646378-03

646251-01

642578-01

642579-01

11260-35

647392-01 BOTTOM PANEL, EGD -48, R.H.

647395-01 BOTTOM PANEL, EGD -48, L.H.

642584-02 BOTTOM PANEL, EGD -72, SINGLE TROUGH

642584-01 BOTTOM PANEL, EGD -72, DOUBLE TROUGH

643066-01 BRACE ASSEMBLY, EGD -48

643356-03 BRACE ASSEMBLY, EGD -72

653844-01 CONTROL PANEL ASSEMBLY

642625-09 KNOB ASSEMBLY

15139-03 INDICATOR LIGHT

31100-82 CONTROL PANEL SEAL

644635-05 THERMOSTAT ASSEMBLY

82111 -00 SCREW, 1/4-20 X 3/4

84315-00 HEX NUT, 1/4 -20

31101-30 SCREW, 10-32 X 1/2

84171-00 HEX NUT, 10 -32

81413-00 SCREW, SELF-TAPPING, 8 -32 X 1/2

84364-00 WING NUT, 5/16 -18

85195-00 FLAT WASHER, 5/16

84317 -00 HEX NUT, 1/4 -20

84362-00 HEX NUT, 5/16 -18

85196-00 FLAT WASHER, 1/4

642626-06 GASKET, GRIDDLE TOP, EGD -48

642626-07 GASKET, GRIDDLE TOP, EGD -72, SINGLE TROUGH

642626-10 GASKET, GRIDDLE TOP, EGD -72, DOUBLE TROUGH

Autres manuels pour EGD-48

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels APW Wyott Plaque

APW Wyott

APW Wyott GGM-18S Manuel utilisateur

APW Wyott

APW Wyott EG-24i Manuel utilisateur

APW Wyott

APW Wyott -36H Manuel utilisateur

APW Wyott

APW Wyott Champion GGM-18H Manuel utilisateur

APW Wyott

APW Wyott HMG-2424 Manuel utilisateur

APW Wyott

APW Wyott EGD-1836 Manuel utilisateur

APW Wyott

APW Wyott EGD48GB Series Manuel utilisateur

APW Wyott

APW Wyott GGT-24H Manuel utilisateur

APW Wyott

APW Wyott Champion GGM-18H Manuel utilisateur

APW Wyott

APW Wyott Champion GGM-24H Manuel utilisateur

APW Wyott

APW Wyott EGD-48 Manuel utilisateur

APW Wyott

APW Wyott GGM-24S Manuel utilisateur

APW Wyott

APW Wyott 1836 Manuel utilisateur

APW Wyott

APW Wyott GGT-18i Manuel utilisateur

APW Wyott

APW Wyott Champion GGM-18H Manuel utilisateur

APW Wyott

APW Wyott GGT-18H Manuel utilisateur

APW Wyott

APW Wyott EG-24S Manuel utilisateur

APW Wyott

APW Wyott -36H Manuel utilisateur

APW Wyott

APW Wyott Champion EG-24H Manuel utilisateur

APW Wyott

APW Wyott HMG-2424i Manuel utilisateur

APW Wyott

APW Wyott HTG-2424i Manuel utilisateur

Manuels Plaque populaires d'autres marques

Proctor-Silex

Proctor-Silex 25340 Manuel utilisateur

New House Kitchen

New House Kitchen NH33-C Manuel utilisateur

Magikitch'n

Magikitch'n 24 Manuel utilisateur

Black Stone

Black Stone 1650 Manuel utilisateur

Anvil

Anvil FTA7116 Manuel utilisateur

Presto

Presto 07030 Manuel utilisateur

Pit Boss

Pit Boss PB2BGT1 Manuel

Dyna-Glo

Dyna-Glo DGL260SNP Manuel utilisateur

Char-Broil

Char-Broil 19952085 Manuel utilisateur

Pit Boss

Pit Boss Ultimate Griddle PB2BGD2 Manuel utilisateur

Airxcel

Airxcel Suburban Elite SOP-1005A Manuel utilisateur

Keating Of Chicago

Keating Of Chicago MIRACLEAN PRE-2000 Manuel utilisateur

Nexgrill

Nexgrill 720-0786A Manuel utilisateur

Outwell

Outwell FH-3047C Manuel utilisateur

Rankam

Rankam Member's Mark GR2298901-MM-02 Guide de référence rapide

Black Stone

Black Stone 1972 Manuel utilisateur

Star

Star Ultra Max 760TA Manuel utilisateur

NuWave

NuWave Precision Cast Iron Griddle Manuel d'utilisation