APsystems APstorage APbattery Manuel utilisateur
APbattery
USER MANUAL
Please read this manual carefully before installing the system
and carry out the installation procedures as per the instructions
Rev1.5 2023-11-29
© All Rights Reserved
APbattery USER MANUAL
1
Table of Contents
CHAPTER 1 INTRODUCTION .................................................................................................................. 2
CHAPTER 2 PRECAUTIONS ....................................................................................................................4
CHAPTER 3 INSTALLATION CYCLE ....................................................................................................5
SECTION 3.1 Check kit components ............................................................................................ 6
SECTION 3.2 Read the instruction manual ................................................................................7
SECTION 3.3 Check installation tools ..........................................................................................7
SECTION 3.4 Risk assesment/compliance to standards ......................................................8
SECTION 3.5 Requirements for wall or support ......................................................................8
SECTION 3.6 Identify a suitable location for the APbattery ...............................................9
SECTION 3.7 Installation space planning ................................................................................. 10
CHAPTER 4 INSTALLATION .................................................................................................................11
SECTION 4.1 Installation for mounting plate .......................................................................... 11
SECTION 4.2 Installation for APbattery ................................................................................... 12
CHAPTER 5 WIRING ................................................................................................................................ 13
SECTION 5.1 Wiring in parallel ..................................................................................................... 16
SECTION 5.2 Wiring in parallel continued ............................................................................... 17
CHAPTER 6 Commissioning, operating,and maintenance .........................................................19
SECTION 6.1 Commissioning ........................................................................................................ 19
SECTION 6.2 Operating ..................................................................................................................20
SECTION 6.3 APbattery care ........................................................................................................21
SECTION 6.4 Maintenance ............................................................................................................ 21
CHAPTER 7 APPENDICES ..................................................................................................................... 22
SECTION 7.1 Troubleshooting ...................................................................................................... 22
SECTION 7.2 Emergency situation ............................................................................................. 22
SECTION 7.3 Specifications .......................................................................................................... 23
SECTION 7.4 Warranty claims and performance ..................................................................24
APbattery USER MANUAL
2
CHAPTER 1 INTRODUCTION
The purpose of this document is to provide information for the owner and
guidelines for the installer to help ensure that the APbattery energy storage system
is properly installed and operates to its designed potential.
This document sets out key criteria that describe a quality system and key design and
installation considerations that should be met in order to achieve this goal. This
document deals with APsystems energy storage system and is applicable for the
following APsystems energy storage system models: APbattery-48V/5.76kWh
These systems should be installed by competent installers who have completed an
Energy storage system installer training course. All specifications and descriptions
contained in this document are verified to be accurate at the time of printing.
Continuous improvement is a goal at APsystems and we reserve the right to make
product modifications at any time.
Thank you for choosing the APsystems APbattery, we are certain that with proper
operation and maintenance our system will provide you with clean renewable solar
electricity for many years.
This manual does not list all precautions needed for safe work. Any energy storage
system must comply with the Health and Safety Requirements and other relevant
standards and Codes of Practice within the country of installation. This manual
provides guidelines for installation but it does not guarantee the quality of
installation work. Please complete all work in a responsible and professional
manner.
All electrical work should be performed by a qualified electrician. It is the qualified
installers responsibility to ensure that the APbattery is suitable for your use to
deliver the best outcomes.
APbattery USER MANUAL
3
CHAPTER 1 INTRODUCTION
Items
Description
On/off button
Used as APbattery indicator and mode switching
APbattery terminals and
communication ports
Used to connect with PCS and operate the system
Safety switch
Used as the main circuit switch; Protect the circuit and avoid
unexpected issues occuring
Aluminum case
Used for natural cooling
Mounting plate
Used for fixing the APbattery on the wall
SOC Indicator
The four indicator lights equate to 25% charge each from left to right
Safety Valve
Valve for pressure release inside APbattery
Battery Terminals And Communication Ports
Safety Switch(ON/OFF)
Safety Valve
APbattery USER MANUAL
4
CHAPTER 2 PRECAUTIONS
WARNING
Failure to observe the precaution described in this section can cause serious injury to
persons or damage to property.
Observe the following precautions:
Risks of explosion
Do not subject the APbattery to strong impacts.
Do not crush or puncture the APbattery.
Do not dispose of the APbattery in a fire.
Risks of fire
Do not expose the APbattery to temperatures in excess of 50℃.
Do not place the APbattery near a heat source such as a fireplace.
Do not expose the APbattery to direct sunlight.
Do not allow the APbattery connectors to touch conductive objects such as wires.
Risks of electric shock
Do not disassemble the APbattery.
Do not touch the APbattery with wet hands.
Do not expose the APbattery to moisture or liquids.
Keep the APbattery away from children and animals.
Risks of damage to the APbattery
Do not allow the APbattery to come in contact with liquids.
Do not subject the APbattery to high pressures.
Do not place any objects on top of the APbattery.
It is recommended to wear the following safety gear when connecting the APbattery
with PCS.
APbattery USER MANUAL
5
CHAPTER 3 INSTALLATION CYCLE
The scope of this document includes the installation of the APbattery to a wall or
support structure, the connection of the D.C. wiring to the PCS. wiring required to
connect the PCS into the building’s electricity supply. A typical project cycle for a
APsystems APbattery is shown below. It shows consideration of the APbattery from the
start of the project through the stages of installation, commissioning, and finishing with
operation and maintenance considerations.
Installation Cycle
01
Check kit contents
02
Read instruction manual
03
Check installation tools
04
Risk assessment/Planning permission
05
Requirements for Wall or Support
06
Identify a suitable location for the APbattery
07
Installation space planning
08
Installation & Wiring
APbattery USER MANUAL
6
CHAPTER 3 INSTALLATION CYCLE
SECTION 3.1 Check kit components
Check kit contents against the included part list with component descriptions and
quantities. Ensure all components and quantities are present before starting the
installation project.
KITS
PICTURES
APbattery
×1
Mounting Plate
×1
Expansion screw
(M8*70)
×8
Ethernet cable
(Super Five Networks)
×1(self-provided)
Modular connector
(8P8C)
×2(self-provided)
Modular adapter
(3 WAYS)
(Multi-machine parallel connection is
applicable)(self-provided)
Modular adapter
(1WAY)
(Multi-machine parallel connection is
applicable)(self-provided)
Terminal blocks
×2
User manual
×1
APbattery USER MANUAL
7
CHAPTER 3 INSTALLATION CYCLE
SECTION 3.2 Read the instruction manual
All of the instructions should be thoroughly read and understood before attempting to
install, wire, operate and maintain the APbattery. Contact with electrically active parts
of the system such as terminals can result in burns, sparks, and lethal shock whether the
module is connected or disconnected. The installation of the APbattery should only be
performed by a qualified licensed professional, including, without limitation, licensed
contractors and licensed electricians. Please keep this manual for reference.
SECTION 3.3 Check installation tools
TOOLS
PICTURE
DESCRIPTION
Percussion drilling
Drill the wall
Screwdriver
Connect the wire to the
battery
Torque wrench
(M8)
Fix the expansion screws
Insulated rubber tape
To prevent leakage and
insulate wires
Multi-meter
Testing the connections
Claw hammer
Hit the screws
Crimping Pliers
Assemble the Ethernet
cable with Modular
connector to
RJ45(T568B)
Levelling instrument
To conduct the leveling
measurement
APbattery USER MANUAL
8
CHAPTER 3 INSTALLATION CYCLE
SECTION 3.4 Risk assesment/compliance to standards
The APbattery can power your home by combing with a PCS to store PV generated
electricity to create a solution for residential and light commercial properties.
Installation standards vary between countries and as such we recommend in all cases
that you check with your local standards authority before you commit to installing our
energy storage system. This document does not address health, safety, electrical or
building regulations matters, a site assessment and works method statement should be
completed prior to commencing the installation.
SECTION 3.5 Requirements for wall or support
WARNING
The APbattery should be installed to a wall capable of supporting its weight, interior walls are
preferred but where installation is on an exterior wall it should be protected from direct rain contact
and sunlight.
Local building regulations and standards should be observed to consider any fire ratings that may be
applicable.
Mounting position
The APbattery can be installed indoors or outdoors .Given the cooling and water-proof
factors of the machine, it is advisable to install the APbattery in a well ventilated and
sheltered place lest it is affected by direct sun radiation, rain, snow and others, so as to
lengthen the operation life of the PCS and the battery.
APbattery USER MANUAL
9
CHAPTER 3 INSTALLATION CYCLE
Mounting Angle
The APbattery should be installed vertically or tilted no more than 15°
Do not install the APbattery on a forward-leaning or horizontal plane.
Install the APbattery on a solid and ventilated surface.
SECTION 3.6 Identify a suitable location for the APbattery
Make sure the weight capacity of bracket location is greater than 80kg.
Make sure the location is not easily accessible by children and in an area free from
explosive or corrosive atmospheres.
For residential installations the energy storage is typically located in a secure
location shielded from direct sunlight and rain.
The APbattery must be mounted vertically on a wall or pole. Do not mount
horizontally as adequate heat dissipation cannot be ensured.
Make sure the APbattery is mounted in a location where the ambient temperature
range is -10 to +45℃. The APbattery may shut down automatically if it excessive
heat or cold temperatures.
A space of at least 100mm to 300mm around the enclosure guarantees optimum
ventilation.
√
√
Table des matières
Manuels Bloc de piles populaires d'autres marques
IOGear
IOGear GBP24V Series Manuel utilisateur
Inventus Power
Inventus Power PROTRXion S-12V100-TRX-HD Manuel utilisateur
Clas Ohlson
Clas Ohlson PW-290A Manuel utilisateur
EINHELL
EINHELL MULTI-Ah Power X-Change Plus Manuel utilisateur
Samsung
Samsung EB-U3300 Manuel utilisateur
ECTIVE
ECTIVE LC Series Manuel utilisateur