Apogee Instruments SU-221 Manuel utilisateur

APOGEE INSTRUMENTS, INC. | 721 WEST 1800 NORTH, LOGAN, UTAH 84321, USA

TEL: (435) 792-4700 | FAX: (435) 787-8268 | WEB: APOGEEINSTRUMENTS.COM

OWNER’S MANUAL

ULTRAVIOLET-A SENSOR

Models SU-221

Rev: 26-Oct-2022

TABLE OF CONTENTS 
Owner’s Manual ............................................................................................................................................................................... 1 
Certificates of Compliance ....................................................................................................................................................... 3 
Introduction ............................................................................................................................................................................. 5 
Sensor Models ......................................................................................................................................................................... 6 
Specifications ........................................................................................................................................................................... 7 
Deployment and Installation.................................................................................................................................................. 10 
Cable Connectors................................................................................................................................................................... 11 
Operation and Measurement ................................................................................................................................................ 12 
Maintenance and Recalibration............................................................................................................................................. 17 
Troubleshooting and Customer Support................................................................................................................................ 18 
Return and Warranty Policy................................................................................................................................................... 19 
 

CERTIFICATE OF COMPLIANCE

EU Declaration of Conformity

This declaration of conformity is issued under the sole responsibility of the manufacturer:

Apogee Instruments, Inc.

721 W 1800 N

Logan, Utah 84321

USA

for the following product(s):

Models: SU-221

Type: Ultraviolet-A Sensor

The object of the declaration described above is in conformity with the relevant Union harmonization legislation:

2014/30/EU Electromagnetic Compatibility (EMC) Directive

2011/65/EU Restriction of Hazardous Substances (RoHS 2) Directive

2015/863/EU Amending Annex II to Directive 2011/65/EU (RoHS 3)

Standards referenced during compliance assessment:

EN 61326-1:2013 Electrical equipment for measurement, control, and laboratory use –EMC requirements

EN 63000:2018 Technical documentation for the assessment of electrical and electronic products with

respect to the restriction of hazardous substances

Please be advised that based on the information available to us from our raw material suppliers, the products

manufactured by us do not contain, as intentional additives, any of the restricted materials including lead (see

note below), mercury, cadmium, hexavalent chromium, polybrominated biphenyls (PBB), polybrominated

diphenyls (PBDE), bis (2-ethylhexyl) phthalate (DEHP), butyl benzyl phthalate (BBP), dibutyl phthalate (DBP), and

diisobutyl phthalate (DIBP). However, please note that articles containing greater than 0.1 % lead concentration

are RoHS 3 compliant using exemption 6c.

Further note that Apogee Instruments does not specifically run any analysis on our raw materials or end products

for the presence of these substances, but we rely on the information provided to us by our material suppliers.

Signed for and on behalf of:

Apogee Instruments, October 2022

Bruce Bugbee

President

Apogee Instruments, Inc.

CERTIFICATE OF COMPLIANCE

UK Declaration of Conformity

This declaration of conformity is issued under the sole responsibility of the manufacturer:

Apogee Instruments, Inc.

721 W 1800 N

Logan, Utah 84321

USA

for the following product(s):

Models: SU-221

Type: Ultraviolet-A Sensor

The object of the declaration described above is in conformity with the relevant UK Statutory Instruments and

their amendments:

2016 No. 1091 The Electromagnetic Compatibility Regulations 2016

2012 No. 3032 The Restriction of the Use of Certain Hazardous Substances in Electrical and Electronic

Equipment Regulations 2012

Standards referenced during compliance assessment:

BS EN 61326-1:2013 Electrical equipment for measurement, control, and laboratory use –EMC requirements

BS EN 63000:2018 Technical documentation for the assessment of electrical and electronic products with

respect to the restriction of hazardous substances

Please be advised that based on the information available to us from our raw material suppliers, the products

manufactured by us do not contain, as intentional additives, any of the restricted materials including lead (see

note below), mercury, cadmium, hexavalent chromium, polybrominated biphenyls (PBB), polybrominated

diphenyls (PBDE), bis (2-ethylhexyl) phthalate (DEHP), butyl benzyl phthalate (BBP), dibutyl phthalate (DBP), and

diisobutyl phthalate (DIBP). However, please note that articles containing greater than 0.1 % lead concentration

are RoHS 3 compliant using exemption 6c.

Further note that Apogee Instruments does not specifically run any analysis on our raw materials or end products

for the presence of these substances, but we rely on the information provided to us by our material suppliers.

Signed for and on behalf of:

Apogee Instruments, October 2022

Bruce Bugbee

President

Apogee Instruments, Inc.

INTRODUCTION

Ultraviolet (UV) radiation constitutes a portion of the electromagnetic spectrum from 100 to 400 nm and is further

subdivided into three wavelength ranges: UV-A (315 to 400 nm), UV-B (280 to 315 nm), and UV-C (100 to 280 nm).

Much of the UV-B and all of the UV-C wavelengths from the sun are absorbed by Earth’s atmosphere. There are

also multiple artificial UV light sources available.

Most UV sensors designed for sunlight measurements are sensitive to UV radiation in the UV-A or UV-B ranges.

Apogee Instruments SU-200 series UV-A sensors detect UV radiation from 300 to 400 nm and are calibrated in

energy flux density units of watts per square meter (W m-2, equal to Joules per second per square meter). The

output can also be expressed in photon flux density units of micromoles per square meter per second (µmol m-2 s-

1).

Typical applications of UV sensors include incoming UV radiation measurement in outdoor environments or in

laboratory use with artificial light sources (e.g., germicidal lamps).

Apogee Instruments SU-200 series UV-A sensors consist of a cast acrylic diffuser, photodiode, and signal processing

circuitry mounted in an anodized aluminum housing and a cable to connect the sensor to a measurement device.

SU-200 sensors are designed for continuous UV-A radiation measurement in indoor or outdoor environments. The

SU-200 series outputs an analog voltage that is directly proportional to UV-A radiation incident on a planar surface

(does not have to be horizontal) where the radiation emanates from all angles of a hemisphere. SU-221 sensors

output a digital signal using SDI-12 communication protocol.

A sensor’s model number and serial number are

located on the bottom of the sensor. If you need

the manufacturing date of your sensor, please

contact Apogee Instruments with the serial number

of your sensor.

SENSOR MODELS

This manual covers the SDI-12 protocol UV-A sensor model SU-221 (in bold below). Additional models are covered

in their respective manuals.

Model

Signal

SU-200

0-10 mV

SU-202

0- 2.5 V

SU-205

0- 5 V

SU-221

SDI-12

SPECIFICATIONS

Calibration Traceability

Apogee UV series sensors are calibrated through side-by-side comparison to the mean of four transfer standard UV

sensors under UV-enhanced T5 fluorescent tubes. The transfer standard UV sensors are calibrated through side-

by-side comparison to an Apogee model PS-300 spectroradiometer under sunlight (clear sky conditions) in Logan,

Utah. The PS-300 is calibrated with a quartz halogen lamp traceable to the National Institute of Standards and

Technology (NIST).

SU-221-SS

Power Supply

5.5 to 24 V DC

Current Draw

1.4 mA (quiescent), 1.8 (active)

Calibration Factor

Custom for each sensor and stored in the firmware

Calibration Uncertainty

± 10 %

Measurement Range

0 to 100 W m-2

Measurement Repeatability

Less than 0.5 %

Long-term Drift

Less than 2 % per year

Non-linearity

Less than 1 %

Response Time

0.6 s, time for detector signal to reach 95 % following a step change; fastest data

transmission rate for SDI-12 circuitry is 1 s

Field of View

180°

Spectral Range

300 to 400 nm (wavelengths where response is greater than 10 % of maximum; see

Spectral Response below)

Directional (Cosine) Response

± 2 % at 45°, ± 5 % at 75°

Temperature Response

Less than 0.1 % per C

Operating Environment

-30 to 85 C; 0 to 100 % relative humidity

Dimension

30.5 mm diameter, 37 mm height

Mass (5 m of cable)

140 g

Cable

5 m of shielded, twisted-pair wire; TPR jacket (high water resistance, high UV stability,

flexibility in cold conditions); pigtail lead wires; stainless steel (316), M8 connector

Cosine Response

Cosine Response Graph

Directional, or cosine, response is

defined as the measurement error at

a specific angle of radiation incidence.

Directional error for Apogee SU-200

series UV-A sensors is approximately ±

2 % and ± 5 % at solar zenith angles of

45° and 75°, respectively.

Mean cosine response of four

Apogee UV-A sensors. Cosine

response was calculated as the

relative difference of UV-A

sensors from the mean of

replicate reference UV-A sensors

deployed outdoors. These data

are the average of the AM and

PM response.

Spectral Response

Spectral response estimate

of Apogee SU-200 UV-A

sensors. Spectral response

was modeled from

sensitivity of the

photodetector and

transmittance of the

diffuser.

DEPLOYMENT AND INSTALLATION

Mount the sensor to a solid surface with the nylon mounting screw provided. To accurately measure UV-A incident

on a horizontal surface, the sensor must be level. An Apogee Instruments model AL-100 Leveling Plate is

recommended to level the sensor when used on a flat surface or being mounted to surfaces such as wood. To

facilitate mounting on a mast or pipe, the Apogee Instruments model AL-120 Solar Mounting Bracket with Leveling

Plate is recommended.

To minimize azimuth error, the sensor should be mounted with the cable pointing toward true north in the

northern hemisphere or true south in the southern hemisphere. Azimuth error is typically less than 1 %, but it is

easy to minimize by proper cable orientation.

In addition to orienting the cable to point toward the nearest pole, the sensor should also be mounted such that

obstructions (e.g., weather station tripod/tower or other instrumentation) do not shade the sensor. Once

mounted, the black cap should be removed from the sensor. The black cap can be used as a protective covering

for the sensor when it is not in use.

Nylon Screw: 10-32x3/8

Model AL-100

Nylon Screw: 10-32x3/8

Model AL-120

Table des matières

Autres manuels Apogee Instruments Accessoires

Apogee Instruments

Apogee Instruments S2-111 Manuel utilisateur

Apogee Instruments

Apogee Instruments SQ-610 Manuel utilisateur

Apogee Instruments

Apogee Instruments SQ-624-SS Manuel utilisateur

Apogee Instruments

Apogee Instruments SQ-600 Series Manuel utilisateur

Apogee Instruments

Apogee Instruments S2-431 Manuel utilisateur

Apogee Instruments

Apogee Instruments SQ-616 Manuel utilisateur

Apogee Instruments

Apogee Instruments SQ-642 Manuel utilisateur

Apogee Instruments

Apogee Instruments SP-522 Manuel utilisateur

Apogee Instruments

Apogee Instruments S2-442 Manuel utilisateur

Apogee Instruments

Apogee Instruments SQ-522 Manuel utilisateur

Apogee Instruments

Apogee Instruments SQ-420X Manuel utilisateur

Apogee Instruments

Apogee Instruments SU-202 Manuel utilisateur

Apogee Instruments

Apogee Instruments SQ-647 Manuel utilisateur

Apogee Instruments

Apogee Instruments SQ-212 Manuel utilisateur

Apogee Instruments

Apogee Instruments SQ-646 Manuel utilisateur

Apogee Instruments

Apogee Instruments PAR-FAR Manuel utilisateur

Apogee Instruments

Apogee Instruments SU-100 Manuel utilisateur

Apogee Instruments

Apogee Instruments SQ-421 Manuel utilisateur

Apogee Instruments

Apogee Instruments SQ-624 Manuel utilisateur

Apogee Instruments

Apogee Instruments SQ-422 Manuel utilisateur

Apogee Instruments

Apogee Instruments SQ-620-SS Manuel utilisateur

Apogee Instruments

Apogee Instruments SU-200 Manuel utilisateur

Apogee Instruments

Apogee Instruments SQ-214 Manuel utilisateur

Apogee Instruments

Apogee Instruments SQ-644 Manuel utilisateur

Manuels Accessoires populaires d'autres marques

Hillco

Hillco 2810 Manuel utilisateur

Siemens

Siemens QSA2700D Manuel de l'opérateur

Contours

Contours ZY024 Manuel utilisateur

Saivod

Saivod VS621 Manuel utilisateur

Virtuox

Virtuox VirtuCLEAN 2.0 Manuel utilisateur

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS Manuel utilisateur

Z-Wave

Z-Wave HSD-200Z Manuel utilisateur

turck

turck FMX-IM-2UPLI63FX Manuel utilisateur

Decagon Devices

Decagon Devices 10HS Manuel utilisateur

UPPAbaby

UPPAbaby Cup Holder Manuel utilisateur

Elko

Elko SmartSensor Leakage Wireless Manuel utilisateur

Grizzly

Grizzly H8371 Manuel utilisateur

Panasonic

Panasonic HG-T Series Manuel utilisateur

IFM Electronic

IFM Electronic Efector 250 Series Guide de référence

DigiDesign

DigiDesign 888/24 I/O Manuel utilisateur

PROZIS

PROZIS QUAY Manuel utilisateur

patagonia

patagonia PSI Vest Manuel utilisateur

SFC Energy

SFC Energy EFOY GO! Manuel utilisateur