Apigy TRON201 Manuel utilisateur
LET’S GET STARTED
INSTALLATION GUIDE
THANK YOU.
We’re incredibly excited to bring Lockitron Bolt to your
door.
If you need any help with setup, please reach out to us
at support@lockitron.com. We’re happy to assist via
FaceTime or Google Hangouts to diagnose any issues.
You can also nd plenty of helpful tips online at
help.lockitron.com or the Lockitron Community which
can be found at community.lockitron.com.
2
START WITH THE INSTALL VIDEO:
LOCKITRON.COM/INSTALL
There you’ll nd the Lockitron Bolt installation video as
well as other videos that assist with troubleshooting
common problems.
https://lockitron.com/install
3
We’ve included everything you need to get Lockitron
Bolt set up.
If your door has difculty closing easily or problems
locking due to misalignment, you’ll want to diagnose
and remedy those issues for best Lockitron Bolt
performance. A metal le can be useful to relieve mild
cases of poor alignment.
While not required, a piece of painters tape can be
helpful to hold your lock cylinder in place during
installation.
PREPARATION
Lockitron
AA
AA
AA
AA
Screwdriver
AA Batteries
2x Mounting Plate Screws
2x Lockitron Bolt Screws
4x Wood Screws
Mounting Plate
Lockitron Bolt
Cylinder Front
Tailpiece + Cylinder
Tapered Latch
Strike Plate
4
Any deadbolt is easily swapped with Lockitron Bolt. You
can verify compatibility at lockitron.com/compatibility.
IS LOCKITRON BOLT COMPATIBLE?
Interconnected locks need to be entirely
removed and a replacement door handle
will need to be installed (not included).
Mortise locks are not drop-in compatible
with Lockitron Bolt. To install Lockitron
Bolt you will need to drill a new hole.
5
Most deadbolts have two Phillips head screws holding
the thumb turn in place (some might have an
additional set of two screws under the thumb turn
which also need to be removed).
1. UNSCREW THUMB TURN
A few deadbolts require an Allen Key
(also known as a hex key) to remove
the thumb turn.
Remove the two screws holding the thumb turn in
place. Hold the front of the lock while doing this to
prevent it from falling out.
6
Remove the old lock cylinder from the front of your door.
Tip: Certain models of Schlage deadbolts can be adapt-
ed to work with the internal portion of Lockitron Bolt. Use
all included Lockitron Bolt components except for the
cylinder and thumb turn screws which you should re-use
from your Schlage lock.
See “Tips and Troubleshooting” for information on using a
Schlage cylinder.
2. REMOVE OLD CYLINDER
7
3. REMOVE EXISTING LATCH
Remove the two screws holding the latch in place.
Depending on how your latch was originally installed, it
may or may not slide out easily.
Tip: If your old latch is difcult to remove, you can use
the screwdriver to carefully pull it out.
To do so, slide the shaft of the screwdriver through one of
the two highlighted holes. Then slowly and carefully pull
on both sides of the screwdriver towards the edge of the
door to slide the latch out.
8
You should now be all set to install Lockitron Bolt! If
your door’s holes (or “prep”) don’t appear similar to the
one above, you might need to make adjustments.
Tip: If your old latch had rounded corners, as shown
above, you might need to use a hammer and chisel to
remove a small amount of material and square off the
recess.
Certain older style or Canadian locks might require addi-
tional chiseling - please contact support@lockitron.com
for more help with this.
4. VERIFY DOOR PREP
9
On the frame of your door, locate
and remove your existing strike
plate.
5. REMOVE EXISTING STRIKE PLATE
10
Table des matières
