Apex Digital BED RACK Manuel utilisateur
INSTALLATION GUIDE
BED RACK
READ BEFORE ASSEMBLING
WARRANTY INFORMATION
THE APEX OF SECURITY
Load. Lock. Go. Whether it’s a
gnarly o-road trek to your deer
camp, daily ride to a worksite
or smooth cruise to your next
game-day tailgate, you don’t have
to worry about your cooler being
secure or vulnerable to theft.
Follow these easy step-by-step
instructions to install this bad boy,
then hit the road with condence.
Please carefully read the guidelines to the installation and use of the Bed Rack before beginning
use. All steps of the installation process are solely your responsibility.
The manufacturer’s warranty is exclusively limited to the repair or replacement of a defective
Bed Rack. Damage to your vehicle, its contents or to any person or property is excluded. Damage
or failure due to improper installation, use or general wear is not covered by this warranty.
Because of the size and structural difference among vehicles, we rely upon your discretion
when attaching the Bed Rack to your vehicle. Additionally, we highly recommend professional
installation of the Bed Rack.
Prior to each use, conrm all components are properly attached, tightened and locked. It is
also important to check for any signs of wear, corrosion or fatigue. If any of these issues are
present, do not use the product. When traveling, periodically inspect the hardware to conrm
it is fastened securely.
Remove the Wings when cooler is not in use.
A 2-year limited warranty is included on parts (except for powder coating) that fail due to a
manufacturing defect. Please visit apexcoolers.com for more information.
COOLER STRAP (2)
LATCH (2)
WING NUT (2)
TOP PLATE (2)
SCREWS (8)
BOTTOM PLATE (2)
WING
ADDITIONAL TOOLS NOT INCLUDED
Recommended
- 7/16” Ratchet Wrench
- 9/32” Drill Bit
- 1/8” Drill Bit
A
B
C
D
E
F
G
A
B
C
D
E
F
G
PARTS LIST
ASSEMBLY OF BED RACK
STEP 1
Carefully measure two lines between the
inside edges of the Bottom Plate as shown in
the diagram. The top line and the bottom line
should have the exact same measurements.
This conrms the Bottom Plates are squared
up correctly and ensures there is an accurate
space for your cooler.
NOTE: If you are installing in a truck bed,
make sure the holes in the Bottom Plate line
up to the top of a ridge or base of a valley on
your bed liner.
WARNING: Look underneath your vehicle and
ensure the chosen location is not near the gas
tank, fuel lines, electrical wires, transmission
lines, cross members or any other integral
vehicle parts. Installation may require that
you temporarily remove your spare tire.
A75 distance between plates is 23 11/16”
A45 distance between plates is 14 1/2”
ASSEMBLY OF BED RACK
STEP 2
Position the Top Plates on top of the Bottom
Plates, making sure to align the holes of
outside edges as shown.
Insert the Wings.
Note: This is only a partial assembly to give you
a sense of how it will sit in your truck bed once
fully installed.
ASSEMBLY OF BED RACK
STEP 3
Slide the APEX A45 or A75 Cooler into place
and make sure everything lines up correctly,
including the holes of the Top and Bottom
Plates. Make sure the plates are sitting
level and have adequate surface area
to drill reliable holes.
ASSEMBLY OF BED RACK
STEP 4
With all components still in place, mark
the location of the 8 holes as shown in
the diagram.
Remove all components from the truck bed
except for the Bottom Plates.
ASSEMBLY OF BED RACK
STEP 5
Drill pilot holes (not full-size permanent holes)
in the spots you’ve marked.
We recommend using a small drill bit (around
1/8“) for the pilot holes. The use of at least four
screws is required on each side, but the Bottom
Plate includes additional holes for exibility or
added security for use as needed
Visually inspect the holes from underneath
your truck to conrm the pilot holes were not
drilled near the gas tank, fuel lines, electrical
wires, transmission lines, cross members or
any other integral vehicle parts.
ASSEMBLY OF BED RACK
STEP 6
Reposition the Bottom Plates on top of the
pilot holes, then place Top Plates on the
Bottom Plates to check alignment. Once
alignment is conrmed, remove the Top Plates.
With the Bottom Plates still in place, drill
eight (8) complete holes through the vehicle
bed where the pilot holes were started.
The recommended drill bit size is 9/32”.
ASSEMBLY OF BED RACK
STEP 7
Place the Top Plates over the Bottom Plates.
Insert the bolts through the eight (8) holes,
then tighten using the washers and nuts
provided. We recommend you hand-tighten
each bolt before using a wrench to rmly
secure each bolt.
Please use only the hardware provided
to ensure secure installation. Use of other
hardware increases the risk of product
movement, damage and likelihood of theft.
Table des matières
Autres manuels Apex Digital Accessoires
