Apera Instruments 2401-C Manuel utilisateur

2401-C Conductivity Electrode

User Manual

Brief Introduction

Apera Instruments 2401-C Conductivity Electrode is featured with a proprietary platinum black sensor

for accurate readings in a wide conductivity range up to 200 mS/cm.

Technical Specifications

Range

0 to 200 mS/cm

Housing

Lead-free Glass

Constant

K=1.0

Connector

BNC

Cable length

3 Ft

Dimension

ø12*145 mm

Temperature sensor

N/A

Operating temperature

32 to 122°F (0 to 50°C)

How to Install the Electrode

1. Find the conductivity BNC socket (where it shows Cond) on the conductivity meter; Open the

rubber cap; Insert the BNC connector of the electrode to the BNC socket while twisting clockwise

until it’s locked.

2. After connecting the new electrode to your meter, adjust the meter’s constant K to 1.0 according

to the instruction of your meter’s manual. Then perform a 2 to 3-point calibration to ensure the

accuracy.

How to Use the Electrode

1. There is a proper amount of deionized water in the cap on top of the electrode. The conductivity

sensor is soaked in it to keep its sensitivity.

2. Before measuring, loosen the bottle cap, then pull out the electrode while twisting

counterclockwise. Place the storage bottle at a safe position.

3. Rinse the electrode with distilled or deionized water and blot-dry it with clean tissue or filter paper.

Rinse the electrode again with your test solution if possible forthe best result. Never rub the sensor.

4. Insert the electrode into your sample solution and stir it for a few seconds in the solution to remove

potential air bubbles. Then wait for the stable reading and take the measurement.

5. After measurement, insert the electrode back into the storage cap and twist it on. If the water in

the cap is contaminated, rinse out the storage cap and fill in new deionized or distilled water.

How to Maintain the Electrode

1. Always rinse the electrode with distilled or deionized water before and after each test and

calibration.

2. For organic residues, rinse the electrode with warm detergent water; For calcium and magnesium

sediments, use 10% lemon acid to clean them off.

3. Store the electrode in the storage cap filled with distilled or deionized water when not in use.

4. Keep the electrode connector clean and dry. Use cotton balls with isopropyl alcohol to clean if it

gets dirty and then blow-dry it. This is to prevent a potential short circuit, which will undermine

the electrode’s performance.

Limited Warranty

We warrant this electrode to be free from defects in material and workmanship and agree to repair or

replace free of charge, at the option of APERA INSTRUMENTS, LLC, any malfunctioned or damaged

product attributable to responsibility of APERA INSTRUMENTS, LLC for a period of SIX MONTHS

from the delivery.

This warranty does not cover any damages due to:

Accidental damage, transportation, storage, improper use, failure to follow the product instructions,

unauthorized repair, normal wear and tear, or any other actions or events beyond our reasonable control.

APERA INSTRUMENTS, LLC

Address: 6656 Busch Blvd, Columbus, OH 43229 Phone: +1 (614) 285-3080

Website: aperainst.com Email: info@aperainst.com

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Apera Instruments Équipement de laboratoire

Apera Instruments

Apera Instruments 201T-S Manuel utilisateur

Apera Instruments

Apera Instruments LabSen 863 Manuel utilisateur

Apera Instruments

Apera Instruments LabSen 213 Manuel utilisateur

Apera Instruments

Apera Instruments 201DJ-C Manuel utilisateur

Apera Instruments

Apera Instruments LabSen 821 Manuel utilisateur

Apera Instruments

Apera Instruments LabSen761 Manuel utilisateur

Manuels Équipement de laboratoire populaires d'autres marques

Qiagen

Qiagen DML 3000 Manuel utilisateur

Queensgate

Queensgate NANOSCAN OP400 Manuel de programmation

Conviron

Conviron GEN1000-GE Manuel utilisateur

Parr Instrument

Parr Instrument 4560 Mode d’emploi

IKA

IKA IC control Manuel utilisateur

Integra

Integra DOSE IT Manuel utilisateur

Agilent Technologies

Agilent Technologies 5800 ICP-OES Manuel utilisateur

Endress+Hauser

Endress+Hauser Cleanfit CPA875 Manuel utilisateur

NI PXI-5422 Manuel

Collomix

Collomix Aqix Manuel utilisateur

SPEX SamplePrep

SPEX SamplePrep 6875 Freezer/Mill Series Manuel utilisateur

Ocean Insight

Ocean Insight FLAME-NIR+ Manuel utilisateur

Parker

Parker ALIGN-MG-NA Manuel utilisateur

BD 644787 Manuel utilisateur

DENTAURUM

DENTAURUM Compact Megaplus Manuel utilisateur

Biuged Laboratory Instruments

Biuged Laboratory Instruments BGD 626 Manuel utilisateur

VWR

VWR SAS Super IAQ Manuel utilisateur

illumina

illumina MiSeqDx Manuel utilisateur