APART REVAMP4100 Manuel utilisateur

REVAMP4100

Instruction manual

Instruction manualREVAMP4100

REVAMP4100 manual

DIGITAL POWER AMPLIFIER

Safety ﬁrst!

• Caution! This professional device needs to be installed by

qualiﬁed personnel only.

• Please check the carton box for any kind of damage on

reception of the goods. In case of a damaged carton, please

contact your dealer before opening the carton.

• !!!! Danger !!!! Exposure to high sound levels may cause a

permanent hearing loss. Individuals vary considerably to sound

pressure level induced hearing loss but nearly everyone will

lose some hearing if exposed to high sound pressure levels for

a sufﬁcient amount of time. Therefore it is recommended that

all persons exposed to equipment capable of producing high

sound pressure levels, such as this ampliﬁer, be protected by

hearing protection while installing or operating this unit.

• Read all documentation before operating your equipment.

• Keep all documentation for future reference.

• Save the carton and packing material even if the equipment has

arrived in good condition.

• Should you ever need to ship the unit, use only the original

factory packing.

• Do not spill water or other liquids into or on the unit.

• Make sure power outlets conform to the power requirements

listed on the back of the unit.

• Do not use the unit if the electrical power cord is frayed or

broken.

• Always operate the unit with the AC ground wire connected to

the electrical system ground.

Instruction manualREVAMP4100

• Set level controls on ampliﬁers all the way down during power-

up to prevent speaker damage if there are high signal levels at

the inputs.

• Do not connect the inputs / outputs of ampliﬁers or consoles

to any other voltage source, such as a battery, mains source, or

power supply, regardless of whether the ampliﬁer or console is

turned on or off.

• Power down & disconnect units from mains voltage before

making connections.

• Do not use the unit near stoves, heat registers, radiators, or

other heat producing devices.

• Do not operate equipment on a surface or in an environment

which may distort the normal ﬂow of air around the unit. If the

unit is used in an extremely dusty or smoky environment, the

unit should be periodically “blown free” of dust.

• Do not remove the cover. Removing the cover will expose you

to potentially dangerous volt ages.

• Do not drive the inputs with a signal level higher than that

required to drive equipment to full output.

• Do not run the output of any ampliﬁer back into another input.

• In case of mal-function this device should be serviced by

qualiﬁed service personnel only.

• This unit has NOT been designed for use in mobile applications,

such as: mobile discobars, mobile PA systems, Live bands, audio

rental systems, …

CAUTION

TO REDUCE THE RISK OF ELECTRIC SHOCK

DO NOT REMOVE COVER OR BACK

NO USER-SERVICEABLE PARTS INSIDE

SERVICING ONLY FOR QUALIFIED PERSONNEL

DIGITAL POWER AMPLIFIER

Features

• 1 rack unit high

• High power class-D power ampliﬁer module

• Bridgeable 4 channel ampliﬁer

• Dynamic output power: 4 x 110 W @ 4 ohms

• Sine wave power per channel: 4 x 100 W @ 4 ohms (500 ms)

• Dynamic bridged output power: 2 x 225 W @ 8 ohms (500 ms)

• Bridged Sine wave output power: 2 x 200 W @ 8 ohms

• High thermal efﬁciency

• Universal switching power supply unit

• No cooling fan

• Low power consumption

• Integrated APC clip limiter

• Balanced euroblock inputs

• Unbalanced inputs on RCA with pass through

• Input level attenuators on all inputs

• Euroblock speaker output connectors

• Extended speaker and amp protection circuits: DC protect, over

current protect, over temperature protect, input overload

• Individual channel mute buttons and versatile LED status

indicators

• Removable rack-ears

Note: the integrated APC clip limiter cannot be bypassed.

34 11

2 125

1. Channel 4 overload led: when this led lights up, you are

overloading the input. Lower the input signal immediately to

prevent distortion.

2. Channel 3 overload led: when this led lights up, you are

overloading the input. Lower the input signal immediately to

prevent distortion.

3. Channel 4 input gain setting: adjust the input gain to the

output level of your source. Make sure to avoid the clip led

lighting up at the strongest input peak level.

4. Channel 3 input gain setting: adjust the input gain to the

output level of your source. Make sure to avoid the clip led

lighting up at the strongest input peak level.

5. Bridge/2 channel mode selector: push the selector switch to

enable bridge mode operation. Minimum load impedance in

bridge mode is 8 ohms. The yellow led underneath the switch

lights up when bridge mode has been activated. Always

Connections

17 18

20 21 22

Instruction manualREVAMP4100

disconnect the speaker(s) before (de-)activating bridge mode !

In bridge mode, the input signal from channel 3 is used.

6. Channel 2 overload led: when this led lights up, you are

overloading the input. Lower the input signal immediately to

prevent distortion.

7. Channel 1 overload led: when this led lights up, you are

overloading the input. Lower the input signal immediately to

prevent distortion.

8. Channel 2 input gain setting: adjust the input gain to the

output level of your source. Make sure to avoid the clip led

lighting up at the strongest input peak level.

9. Channel 1 input gain setting: adjust the input gain to the

output level of your source. Make sure to avoid the clip led

lighting up at the strongest input peak level.

10. Bridge/2 channel mode selector: push the selector switch to

enable bridge mode operation. Minimum load impedance in

bridge mode is 8 ohms. The yellow led underneath the switch

lights up when bridge mode has been activated. Always

disconnect the speaker(s) before (de-)activating bridge mode !

In bridge mode, the input signal from channel 1 is used.

11. Channel 4 speaker output on 2 pole euroblock connector.

12. Channel 3 speaker output on 2 pole euroblock connector.

13. Channel 2 speaker output on 2 pole euroblock connector.

DIGITAL POWER AMPLIFIER

14. Channel 1 speaker output on 2 pole euroblock connector.

15. Channel 4 unbalanced input and link cinch connector: connect

the line level input signal for channel 4 here. Line level is 0 dBV.

Input and link connector are internally connected 1 on 1.

16. Channel 3 unbalanced input and link cinch connector: connect

the line level input signal for channel 3 here. Line level is 0 dBV.

Input and link connector are internally connected 1 on 1. This

connector is also used in bridge mode.

17. Channel 4 balanced input on 3 pole euroblock connector.

18. Channel 3 balanced input on 3 pole euroblock connector: this

connector is used in bridge mode.

19. Channel 2 unbalanced input and link cinch connector: connect

the line level input signal for channel 2 here. Line level is 0 dBV.

Input and link connector are internally connected 1 on 1.

20. Channel 1 unbalanced input and link cinch connector: connect

the line level input signal for channel 1 here. Line level is 0 dBV.

Input and link connector are internally connected 1 on 1. This

connector is also used in bridge mode.

21. Channel 2 balanced input on 3 pole euroblock connector.

22. Channel 1 balanced input on 3 pole euroblock connector: this

connector is used in bridge mode.

23. Mains inlet: connect the mains power cord here.

Instruction manualREVAMP4100

DIGITAL POWER AMPLIFIER

Operation

1. Removable rack ears for 19” rack mounting.

2. Power switch: after switching on the power, the power led will

light up after approx 1 second.

3. Power led

4. Channel 1 status led bar and mute switch: when the mute

switch is pressed, the orange “LIMIT – MUTED” led will light

up. This led will also light up when the internal limiter is

activated to avoid the ampliﬁer from being overloaded by high

input signals. The “CLIP – OVERLOAD” led indicates that the

power ampliﬁer is clipping: reduce the input signal at once

whenever this occurs !!! The green “SIGNAL - -40dB” led will

light up when an input signal is present.

5. Bridged CH 1-2 led

1 12 3 4

Table des matières

Autres manuels APART Amplificateur

APART

APART pubdrive2000 Manuel utilisateur

APART

APART MA200CDR Manuel utilisateur

APART

APART PM1122 Manuel utilisateur

APART

APART MA-35 Manuel utilisateur

APART

APART REVAMP4120T Manuel utilisateur

APART

APART REVAMP2600 Manuel utilisateur

APART

APART MA200 Manuel utilisateur

APART

APART REVAMP8250 Manuel utilisateur

APART

APART Concept 1T Manuel utilisateur

APART

APART MA30 Manuel utilisateur

APART

APART REVAMP2060T Manuel utilisateur

APART

APART PA8250 Manuel utilisateur

APART

APART REVAMP2250 Manuel utilisateur

APART

APART Champ-4 Manuel utilisateur

APART

APART SB-160 Manuel utilisateur

APART

APART Champ-One Manuel utilisateur

APART

APART MA125 Manuel utilisateur

APART

APART vinci 2125 Manuel utilisateur

APART

APART Champ - 4 Manuel utilisateur

APART

APART MA247 series Manuel utilisateur

APART

APART PIR7600 Manuel utilisateur

APART

APART REVAMP4120T Manuel utilisateur

APART

APART AUDIOSYSTEM8.8 Manuel utilisateur

APART

APART REVAMP1680 Manuel utilisateur

Manuels Amplificateur populaires d'autres marques

ASTRO

ASTRO HVO V40 P Manuel utilisateur

Marantz

Marantz SUPERSCOPE BLA-545 Instructions de montage

NAD

NAD CI980 Manuel utilisateur

Technics

Technics SE-CH770 Manuel utilisateur

Harman Kardon

Harman Kardon HK6300 Manuel utilisateur

NAD

NAD T975 Manuel utilisateur

McIntosh

McIntosh MA6850 Manuel utilisateur

Electro-Harmonix

Electro-Harmonix ENGLISH MUFF’N Manuel utilisateur

Viatron

Viatron Autrix Manuel utilisateur

GME

GME GA9800 Manuel utilisateur

Atlas

Atlas CP700 Manuel utilisateur

Roland

Roland KC-1000 Manuel utilisateur

Pyle

Pyle PFMRA350BW Manuel utilisateur

Advantage

Advantage S-250 Manuel utilisateur

IRT Electronics

IRT Electronics DVA-3007 Manuel utilisateur

Dimavery

Dimavery BA-100 Series Manuel utilisateur

Sony

Sony XM-S400D Manuel utilisateur

Schertler

Schertler ROY X Manuel utilisateur