ANTAIRA RS232 Manuel utilisateur

Thank you for purchasing this 4-Port RS232 Serial PCI Card. It is an

add-in card that connects to a PC or server via the PCI Bus to provide

high-speed serial connectivity. The serial ports are fully compatible

with RS232 standard by the complete bundled drivers.

Each port supports 15KV ESD protection feature. It provides an ideal

solution for most critical applications.

Features:

Fully PCI Bus 2.3 and PCI Power Management 1.1 Compliant

Supports 4 RS232 serial ports over a PCI Slot

Supports low profile form factor by an optional short bracket

Fully 16C1050 High performance UART channels

±15kV IEC1000-4-2 ESD Protection for RS-232 I/O's

Supports both 3.3V and 5V PCI Slots

Baud rate up to 921.6 Kbps in a asynchronous mode

256-byte deep FIFO per transmitter and receiver

Supports 5V or 12V over DB44 connector pins, the

Fan out Octopus Cable Supplies it to DB9 Connectors

Software/Hardware Flow Control & Xoff Re-Transmit Function

Supports Win98/ME, 2K, 2003, XP, Vista, Win7, 8, 8.1 and Linux

4-Port RS232 Serial PCI Card

Installation Guide

1. Introduction

DB44 fan out cable

PCI connector

Normal

Profile

Bracket

Low

Profile

Bracket

4-Port RS232 Serial PCI Card

JP3 – PME Enable/Disable Jumper: This jumper provides an option to

enable the PCI card to wake up the system by its serial ports. The

default was set at “DIS” (disabled).

JP3

Settings

PME Disabled

(default)

PME Enabled

S1_PWR, S2_PWR, S3_PWR and S4_PWR: - Pin-9 Power Setting

Jumpers for S1, S2, S3 and S4 Respectively: The design of each

2. Connector Layout

J2: Aux. Power

Connector

JP2: Aux Power

Source Selector

JP4: Factory use

only, should be

kept at ”CEN”

JP3: PME

Enable/Disable

S1_PWR~S4_PWR: Pin 9

Power Selector for

S1~S4

3. Jumper Settings

ENA DIS

J3, J5, J4, J6:

Internal Connectors

for S1, S2, S3, S4

JP1: UART

Power

Selector

4-Port RS232 Serial PCI Card

DB9 male connector has an option to supply DC power to its Pin-9.

Pin number 9 of the DB9 connector was defined for RS232 RI (Ring

Indicator) signal. Since some applications do NOT use this signal, in

this case, Pin-9 can be used to deliver DC power for the serial

devices. This product provides 2 settings for the power, +5V and

+12V. The default factory setting was set at “RI”, i.e. no power

supplied on the DB9M connector’s pin-9.

Pin-9 Power Setting Table:

S1_PWR, S2_PWR, S3_PWR,

S4_PWR Settings

Description

(default)

No Power Supplied on Pin-9

(default)

+5V DC on Pin-9

+12V DC on Pin-9

JP2 – 5V and 12V Power Source Selection Jumper: To supply power

to Pin-9 of each DB9 connector, you need +5V and +12V power

source. Both can be selected from either PCI golden fingers or

from J2 AUX Power connector instead. If you select from J2, then

you need connect a power cable to connect it to your system

power supply.

12V

DIS

12V

DIS

12V

DIS

4-Port RS232 Serial PCI Card

JP2

Description

(default)

Both +5V and +12V are

from PCI golden fingers

(default)

Both +5V and +12V are

from J2 4-pin AUX power

connector

JP1 – UART Power: This jumper is used to select the power for the

RS232 transceivers. The default setting is “+3.3V”. Due to some old

RS232 devices need higher swing voltage level, in this case,

please move the jumper to “+5V” instead.

JP1

Description

(default)

RS232 Transceivers

(default)

RS232 Transceivers

I5V

X5V

X12V

I12V

I5V

X5V

X12V

I12V

+5V

+3.3V

+5V

+3.3V

4-Port RS232 Serial PCI Card

Note:

PLEASE DO NOT LET WINDOWS AUTO SEARCH THE DRIVERS ON THE CD, it

will cause problems because the INF files will be conflict in this case.

Instead, please browse to the correct location (folder) manually to

make sure the correct drivers are chosen and installed correctly.

4. Software Installation

Drivers are in each

corresponding folder

4-Port RS232 Serial PCI Card

The pin assignment of the 4 DB9 male connectors on the fan

out cable as follows:

DB9(Male) to DB9(Male) Wiring:

5. Connector Pin Assignments

DB9(PCI Card) DB9(Serial Device)

1 DCD 1 DCD

2 RXD 2 RXD

3 TXD 3 TXD

4 DTR 4 DTR

5 GND 5 GND

6 DSR 6 DSR

7 RTS 7 RTS

8 CTS 8 CTS

4-Port RS232 Serial PCI Card

Type

Specifications

Connectors

Cable

Bus Interface

Number of Ports

RS-232 Signals

Baud Rate

Data Bits

Stop Bits

I/O address/IRQ

Parity

Flow Control

Power Requirement

Operating Temperature

Operating Humidity

Storage Temperature

DB44 Female

DB44M-to-DB9MX4 Octopus type

32-bit PCI

TXD, RXD, RTS, CTS, DTR, DSR, DCD, GND

110 bps to 921.6Kbps

5,6,7,8

1, 1.5, 2

Plug-and-Play (various)

None, Even, Odd

RTS/CTS, XON/XOFF

3.3V/200mA

0 to 55°C(32 to 132°F)

5 to 95% RH

-20 to 85°C (-4 to 185°F)

6. Specifications

Table des matières

Autres manuels ANTAIRA Carte PCI

ANTAIRA

ANTAIRA MSC-204A1-S Manuel utilisateur

ANTAIRA

ANTAIRA RS232 Manuel utilisateur

ANTAIRA

ANTAIRA MSC-202ALP Manuel utilisateur

ANTAIRA

ANTAIRA SC-102AL-1 Manuel utilisateur

ANTAIRA

ANTAIRA RS232 Manuel utilisateur

ANTAIRA

ANTAIRA MSC-202A-V2 Manuel utilisateur

ANTAIRA

ANTAIRA MSC-204B1 Manuel utilisateur

ANTAIRA

ANTAIRA msc-401a1 Manuel utilisateur

ANTAIRA

ANTAIRA msc-116a Manuel utilisateur

ANTAIRA

ANTAIRA MSC-102B1L Manuel utilisateur

ANTAIRA

ANTAIRA MSC-104B Manuel utilisateur

ANTAIRA

ANTAIRA MSC-208A Manuel utilisateur

ANTAIRA

ANTAIRA MSC-202AL Manuel utilisateur

ANTAIRA

ANTAIRA MSC-102B1 Manuel utilisateur

ANTAIRA

ANTAIRA msc-216a Manuel utilisateur

ANTAIRA

ANTAIRA Dual Channel Gigabit Ethernet PCIe Card Manuel utilisateur

ANTAIRA

ANTAIRA MSC-204A2 Manuel utilisateur

ANTAIRA

ANTAIRA MSC-202B1 Manuel utilisateur

ANTAIRA

ANTAIRA MSC-102B1-SI Manuel utilisateur

Manuels Carte PCI populaires d'autres marques

ERMA

ERMA SSI 1417 Manuel utilisateur

SIIG

SIIG CyberSerial Dual PCI Instructions de montage

Moxa Technologies

Moxa Technologies CP-102E Manuel utilisateur

I-Bus

I-Bus IBC2602 Manuel utilisateur

Exsys

Exsys EX-60102 Manuel utilisateur

Chelsio Communications

Chelsio Communications T5 Series Manuel utilisateur

Conrad Electronic

Conrad Electronic 97 46 71 Manuel utilisateur

Micro Innovations

Micro Innovations USB650A Manuel utilisateur

KTI Networks

KTI Networks KF-310 Manuel utilisateur

Asus

Asus SpaceLink WL230 Manuel utilisateur

SIIG

SIIG SC2475 Manuel utilisateur

TRENDnet

TRENDnet TEW-703PI Manuel utilisateur

Belkin

Belkin F5D7000F Manuel utilisateur

Pericom

Pericom PI7C7100 Manuel utilisateur

ADLINK Technology

ADLINK Technology cPCI-3548 Manuel utilisateur

Digium

Digium TE200 Series Manuel utilisateur

Allo.com

Allo.com 2nd Gen E1/T1/J1 Manuel utilisateur

Western Digital

Western Digital FireWire PCI Adapter Manuel utilisateur