Anritsu MP2110A BERTWave Manuel utilisateur

Document No.: M-W3831AE-18.0

ANRITSU CORPORATION

MP2110A

BERTWave

Operation Manual

For safety and warning information, please read this

manual before attempting to use the equipment.

Keep this manual with the equipment.

18th Edition

Safety Symbols

To prevent the risk of personal injury or loss related to equipment malfunction, Anritsu Corporation uses the following

safety symbols to indicate safety-related information. Ensure that you clearly understand the meanings of the

symbols BEFORE using the equipment. Some or all of the following symbols may be used on all Anritsu equipment.

In addition, there may be other labels attached to products that are not shown in the diagrams in this manual.

Symbols used in manual

This indicates a very dangerous procedure that could result in serious injury or

death if not performed properly.

This indicates a hazardous procedure that could result in serious injury or death if

not performed properly.

This indicates a hazardous procedure or danger that could result in light-to-severe

injury, or loss related to equipment malfunction, if proper precautions are not taken.

Safety Symbols Used on Equipment and in Manual

The following safety symbols are used inside or on the equipment near operation locations to provide information

about safety items and operation precautions. Ensure that you clearly understand the meanings of the symbols and

take the necessary precautions BEFORE using the equipment.

This indicates a prohibited operation. The prohibited operation is indicated

symbolically in or near the barred circle.

This indicates an obligatory safety precaution. The obligatory operation is indicated

symbolically in or near the circle.

This indicates a warning or caution. The contents are indicated symbolically in or

near the triangle.

This indicates a note. The contents are described in the box.

These indicate that the marked part should be recycled.

MP2110A

BERTWave

Operation Manual

13 January 2017 (First Edition)

24 August 2020 (18th Edition)

publisher.

The operational instructions of this manual may be changed without prior notice.

Printed in Japan

DANGER

WARNING

CAUTION

For Safety

iii

WARNING

●ALWAYS refer to the operation manual when working near locations

at which the alert mark shown on the left is attached. If the advice in

the operation manual is not followed, there is a risk of personal injury

or reduced equipment performance. The alert mark shown on the left

may also be used with other marks and descriptions to indicate other

dangers.

●Overvoltage Category

This equipment complies with overvoltage category II defined in IEC

61010. DO NOT connect this equipment to the power supply of

overvoltage category III or IV.

●To ensure that the equipment is grounded, always use the supplied

3-pin power cord, and insert the plug into an outlet with a ground

terminal. If power is supplied without grounding the equipment, there

is a risk of receiving a severe or fatal electric shock or causing

damage to the internal components.

●Only qualified service personnel with a knowledge of electrical fire and

shock hazards should service this equipment. This equipment cannot

be repaired by the operator. DO NOT attempt to remove the equipment

covers or unit covers or to disassemble internal components. There are

high-voltage parts in this equipment presenting a risk of severe injury

or fatal electric shock to untrained personnel. In addition, there is a risk

of damage to precision components.

●The performance-guarantee seal verifies the integrity of the

equipment. To ensure the continued integrity of the equipment, only

Anritsu service personnel, or service personnel of an Anritsu sales

representative, should break this seal to repair or calibrate the

equipment. Be careful not to break the seal by opening the equipment

or unit covers. If the performance-guarantee seal is broken by you or

a third party, the performance of the equipment cannot be

guaranteed.

Repair

Electric Shock

Calibration

For Safety

WARNING

●This equipment should always be positioned in the correct manner. If

the cabinet is turned on its side, etc., it will be unstable and may be

damaged if it falls over as a result of receiving a slight mechanical

shock.

Always set up the equipment in a position where the power switch

can be reached without difficulty.

Falling Over

For Safety

CAUTION

●Always remove the main power cable from the power outlet before

cleaning dust around the power supply and fan.

- Clean the power inlet regularly. If dust accumulates around the

power pins, there is a risk of fire.

- Keep the cooling fan clean so that the ventilation holes are not

obstructed. If the ventilation is obstructed, the cabinet may

overheat and catch fire.

●Never input a signal of more than the indicated value between the

measured terminal and ground. Input of an excessive signal may

damage the equipment.

●Always take the following anti-static measures to prevent the internal

circuit from being damaged when using a connector indicated by the

symbol shown on the left.

- Wear a wrist strap connected to the ground terminal of this

equipment.

- Connect the ground wires of this equipment, external measuring

instruments and DUT before connecting a coaxial cable.

- Eliminate static electricity charged between the cores and outer

conductors of an external device and the coaxial cable, before

connecting this equipment and the external device.

This equipment uses a Poly-carbon monofluoride lithium battery to

backup the memory. This battery must be replaced by service personnel

when it has reached the end of its useful life; contact the Anritsu sales

section or your nearest representative.

Note: The battery used in this equipment has a maximum useful life of

2 years. It should be replaced before this period has elapsed.

The life of the battery will vary depending on the length of equipment

usage and the operating environment.

The following conditions may be observed if the battery has expired:

●When power to the equipment is supplied, the time display may no

longer match the actual time.

Replacing Memory

Back

-up Battery

Cleaning

Check Terminal

Static Sensitive

For Safety

CAUTION

This equipment uses USB flash drive as external storage media for

storing data and programs.

If this media is mishandled or becomes faulty, important data may be lost.

To prevent this chance occurrence, all important data and programs

should be backed-up.

Anritsu will not be held responsible for lost data.

Pay careful attention to the following points.

●Never remove the USB flash drive from the instrument while it is

being accessed.

●The USB flash drive may be damaged by static electric charges.

●Anritsu has thoroughly tested all external storage media such as USB

flash drive, Hard disk drive and DVD drive. Users should note that

external storage media may not have been tested by Anritsu, thus

Anritsu cannot guarantee the performance or suitability of such

media.

External

Storage Media

For Safety

vii

CAUTION

The instrument is equipped with a SSD (Solid State Drive) from which,

as with any flash memory, data may be lost because of limitation of

writing times. It is recommended to periodically back up all important

data and programs to protect them from being lost accidentally.

Anritsu will not be held responsible for lost data.

To reduce the possibility of data loss, particular attention should be given

to the following points.

●The equipment should only be used within the recommend

temperature range, and should not be used in locations where the

temperature may fluctuate suddenly.

●Always follow the guidelines to ensure that the equipment is set up in

the specified manner.

●Always ensure that the fans at the rear and side of the equipment are

not blocked or obstructed in any way.

●Exercise care not to bang or shake the equipment whilst the power is

on.

●Never disconnect the mains power at the plug or cut the power at the

breaker with the equipment turned on.

The life span of certain parts used in this equipment is determined by the

operating time or the power-on time. Due consideration should be given to

the life spans of these parts when performing continuous operation over

an extended period. The safety of the equipment cannot be guaranteed if

component parts are used beyond their life spans. These parts must be

replaced at the customer's expense even if within the guaranteed period

described in Warranty at the beginning of this manual.

For details on life-span, refer to the corresponding section in this manual.

Coaxial switch: One million times (Switching scope optical input

connector)

Coaxial switch: Five million times (Switching BERT clock output

channel)

SSD

Lifetime of Parts

For Safety

viii

CAUTION

This instrument is designed for an industrial environment.

In a residential environment this instrument may cause radio interference

in which case the user may be required to take adequate measures.

Exposure to corrosive gases such as hydrogen sulfide, sulfurous acid,

and hydrogen chloride will cause faults and failures.

Note that some organic solvents release corrosive gases.

Use in a

Residential

nvironment

se in Corrosive

Atmospheres

Equipment Certificate

Anritsu Corporation certifies that this equipment was tested before shipment

using calibrated measuring instruments with direct traceability to public

testing organizations recognized by national research laboratories, including

the National Institute of Advanced Industrial Science and Technology, and

the National Institute of Information and Communications Technology, and

was found to meet the published specifications.

Anritsu Warranty

Anritsu Corporation will repair this equipment free-of-charge if a malfunction

occurs within one year after shipment due to a manufacturing fault, and

software bug fixes will be performed in accordance with the separate

Software End-User License Agreement, provide, however, that Anritsu

Corporation will deem this warranty void when:

●The fault is outside the scope of the warranty conditions separately

described in the operation manual.

●The fault is due to mishandling, misuse, or unauthorized modification or

repair of the equipment by the customer.

●The fault is due to severe usage clearly exceeding normal usage.

●The fault is due to improper or insufficient maintenance by the customer.

●The fault is due to natural disaster, including fire, wind or flood,

earthquake, lightning strike, or volcanic ash, etc.

●The fault is due to damage caused by acts of destruction, including civil

disturbance, riot, or war, etc.

●The fault is due to explosion, accident, or breakdown of any other

machinery, facility, or plant, etc.

●The fault is due to use of non-specified peripheral or applied equipment or

parts, or consumables, etc.

●The fault is due to use of a non-specified power supply or in a

non-specified installation location.

●The fault is due to use in unusual environments(Note).

●The fault is due to activities or ingress of living organisms, such as insects,

spiders, fungus, pollen, or seeds.

In addition, this warranty is valid only for the original equipment purchaser. It

is not transferable if the equipment is resold.

Anritsu Corporation shall assume no liability for damage or financial loss of

the customer due to the use of or a failure to use this equipment, unless the

damage or loss is caused due to Anritsu Corporation’s intentional or gross

negligence.

Note:

For the purpose of this Warranty, "unusual environments" means use:

●In places of direct sunlight

●In dusty places

●Outdoors

●In liquids, such as water, oil, or organic solvents, and medical fluids, or

places where these liquids may adhere

●In salty air or in place chemically active gases (sulfur dioxide, hydrogen

sulfide, chlorine, ammonia, nitrogen dioxide, or hydrogen chloride etc.)

are present

●In places where high-intensity static electric charges or electromagnetic

fields are present

●In places where abnormal power voltages (high or low) or instantaneous

power failures occur

●In places where condensation occurs

●In the presence of lubricating oil mists

●In places at an altitude of more than 2,000 m

●In the presence of frequent vibration or mechanical shock, such as in cars,

ships, or airplanes

Anritsu Corporation Contact

In the event of this equipment malfunctions, please contact an Anritsu

Service and Sales office. Contact information can be found on the last page

of the printed version of this manual, and is available in a separate file on the

PDF version.

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Anritsu Équipement de test

Anritsu

Anritsu MT8850A Manuel utilisateur

Anritsu

Anritsu MP1800A Manuel utilisateur

Anritsu

Anritsu AutoCal 36581NNF Manuel utilisateur

Anritsu

Anritsu MG369 A Series Manuel utilisateur

Anritsu

Anritsu Network Master Series Manuel utilisateur

Anritsu

Anritsu Site Master S112 Manuel utilisateur

Anritsu

Anritsu 3656B W1 Manuel utilisateur

Anritsu

Anritsu MP1800A Manuel utilisateur

Anritsu

Anritsu MT1000A Network Master Pro Manuel utilisateur

Anritsu

Anritsu MT1000A Network Master Pro Manuel utilisateur

Anritsu

Anritsu MS9720A Manuel utilisateur

Anritsu

Anritsu Site Master S113B Manuel utilisateur

Anritsu

Anritsu MX900030A Manuel utilisateur

Anritsu

Anritsu 681XXC Manuel utilisateur

Anritsu

Anritsu MT1000A Network Master Pro Manuel utilisateur

Anritsu

Anritsu SQA-R MP1900A Manuel de référence

Anritsu

Anritsu MT8870A Manuel utilisateur

Anritsu

Anritsu MT9810A Manuel utilisateur

Anritsu

Anritsu 691 B Series Manuel utilisateur

Anritsu

Anritsu MD8480A Manuel utilisateur

Anritsu

Anritsu Precision AutoCal 36585 Series Manuel utilisateur

Anritsu

Anritsu MT8852B Manuel du propriétaire

Anritsu

Anritsu MD8470A Manuel utilisateur

Anritsu

Anritsu ME7840A Manuel utilisateur

Manuels Équipement de test populaires d'autres marques

SMART

SMART KANAAD SBT XTREME 3G Series Manuel utilisateur

Agilent Technologies

Agilent Technologies BERT Serial Manuel utilisateur

Agilent Technologies

Agilent Technologies N3280A Manuel utilisateur

Vernier

Vernier Go Direct Voltage Manuel utilisateur

Lifeloc

Lifeloc R.A.D.A.R. Manuel utilisateur

Fluke

Fluke T5-600 Instructions d'utilisation et d'installation

Mercury

Mercury TSL01 Manuel utilisateur

MAHA

MAHA MBT Series Manuel utilisateur

Fuji Electric

Fuji Electric P-61 Manuel utilisateur

ETC

ETC SealerAtor Manuel utilisateur

Skyfine

Skyfine ETHYWAY V2 Manuel utilisateur

Appion

Appion G5 Twin Manuel utilisateur

PCB Piezotronics

PCB Piezotronics 8159-0112A Manuel utilisateur

BW Technologies

BW Technologies MicroDock II Manuel utilisateur

Sun Nuclear

Sun Nuclear 1027 Manuel utilisateur

Biomark

Biomark HPR LITE READER Manuel utilisateur

Hioki

Hioki 3169-20 Manuel utilisateur

Ashcroft

Ashcroft ATE-100 Manuel utilisateur