Anker PowerConf S3 Manuel utilisateur
Anker PowerConf S3
User Manual
English 01
Deutsch 09
Español 17
Français 25
Italiano 33
Português 41
Pусский 49
日本語 57
한국어 65
简体中文 73
繁體中文 81
89
EN 01
At a Glance
4 6
8 9 107
2 31 5
131211
1Multi-function button 8Power button
2
Volume down button
9
Bluetooth button
3Mute button 10 Bluetooth LED
4Phone call button 11 USB-A port for charge-out
5Volume up button 12 Audio output port
6
Status LED
13
USB-C port for charge-in and
connection to PC
7Power LED
02 EN
Connecting
a) Connect to your PC by using a USB-C cable
b) Connect to your PC or mobile device via Bluetooth
pairing
When powered on for the rst time, PowerConf S3 will automatically enter the
Bluetooth pairing mode.
Anker PowerConf S3
EN 03
Flashes blue Bluetooth pairing
Steady blue Bluetooth connected
• Each time you power on PowerConf S3, it will automatically connect with
the last successfully connected device if available.
• To disconnect Bluetooth, press the Bluetooth button again.
Powering On/Off
Press and hold the power button for 2 seconds to power on. The status LED
will light on clockwise and then fade out.
To power off, press and hold the power button for 2 seconds.
2”
04 EN
• PowerConf S3 will automatically power on once connected to your PC.
• PowerConf S3 will automatically power off after 30 minutes of inactivity or
no source.
Button Controls
Press or press and hold Volume up/down
Press Answer/End a call
Press and hold for 2 seconds Reject a call
Press Mute or restore the
microphone
Press Play/Pause music
Status LED
Lights up white for 2 seconds USB connected to PC
Breathes green Coming call
EN 05
Partially lights up blue Sound direction detected
Lights up blue clockwise or
counterclockwise Increase/Decrease volume
Turns red Muted
Lights up green Press Power button to check the battery
level
Charging
a) Charging PowerConf S3
06 EN
b) Charging an external device
• When powered off or being charged, PowerConf S3 won’t charge out.
• When the remaining battery is less than 30%, the charge out current will
be 5V 1A; if less than 10%, PowerConf S3 won’t charge out.
Audio Output
Connect an external speaker to the AUX OUT port of PowerConf S3 by using
an AUX cable (not provided). The audio will be played through the speaker.
EN 07
AnkerWork APP
Download the AnkerWork app to enhance your experience.
08 EN
Specifications
Specications are subject to change without notice.
Charge input 5V 2A
Charge out 5V 2.1A
Rated output power 3W RMS
Battery capacity 5200 mAh
Charging time 4 hours
Talktime 24 hours
Driver size 1 x 1.75” (full range)
Frequency response 20 Hz - 20 kHz
Bluetooth version V 5.3
Bluetooth range 10 m / 33 ft
Autres manuels pour PowerConf S3
1
Table des matières
Langues :
Autres manuels Anker Téléphone
Anker
Anker PowerConf S500 Manuel utilisateur
Anker
Anker PowerConf S3 Manuel utilisateur
Anker
Anker PowerConf Manuel utilisateur
Anker
Anker PowerConf S500 Manuel utilisateur
Anker
Anker PowerConf S330 Manuel utilisateur
Anker
Anker PowerConf+ Manuel utilisateur
Anker
Anker PowerConf Manuel utilisateur
Anker
Anker PowerConf Manuel utilisateur
Anker
Anker PowerConf+ Manuel utilisateur
Anker
Anker A3301 Manuel utilisateur
