Analog way SPU001 Manuel utilisateur
Thank you for choosing Analog Way and the Secure Power Unit. By following these simple steps, you will be able to
set up and use your external power supply secure unit. Dedicated to Analog Way’s LiveCore™ series (NeXtage 08,
NeXtage 16, SmartMatriX Ultra,Ascender 16, Ascender 32 &Ascender 48), the Secure Power Unit allows a redundant
supply and a protecon against power cuts or failures.
• 1 x Secure Power Unit 1 RU Frame (SPU001)
• 1 x LiveCore™ power supply (OPT-SPS)
• 1 x SPU baery (OPT-SPUBATTERY)
• 1 x SPU adaptator block with aached cable
• 1 x IEC power supply cable
• 1 x Grounding cable
• 1 x RS232 cable
• 1 x Rear rack rail kit
• 1 x Quick start guide*
* Quick start guide is also available on www.analogway.com
TEST buon Baery charge
PSU Status
SpeakON™
DC Power 12V Baery Power Supply Unit 2 Power Supply Unit 1
RS232 port
Ground
Secure Power Unit - Ref. SPU001
QUICK START GUIDE
WHAT’S IN THE BOX
PANELS DESCRIPTION
Go to our website to register your product(s)
and be noed about new rmware updates:
hp://bit.ly/AW-Register
THE TEST BUTTON
Pushing shortly the TEST buon performs a test of the Secure Power Unit. It enables a view of the Secure Power Unit
supply and of the baery charge without any LiveCore™ device connected (or in standby). A long press will perform a
forced charge of the baery if the baery charge is lower than 95% (only when the LiveCore™ device is in standby or
without any LiveCore™ connected).
The Secure Power Unit has been designed to replace the power supply of LiveCore™ devices. It provides a redundant
supply plus a baery.
If a power supply unit stops working, the other one supplies the device. If both stop working, the baery keeps the
device switched on for a duraon of 5-10 minutes to enable the device to be turned o properly or x the electrical
issue.
When a LiveCore™ device is powered on using the Secure Power Unit, the baery is automacally charging.
It is possible to charge the baery when no LiveCore™ device is running. (see Test Buon descripon).
To nd informaon about the Secure Power Unit on the Web RCS (Setup > Services > SPU), the Secure Power Unit has
to be connected to the LiveCore™ device through an RS232 cable.
PSU LED Status
These LEDs show the status of PSU 1 and 2 slots.
BATTERY CHARGE LEDS
These LEDs give the status of the charging rate.
When charging, the LEDs ash unl full charge
is reached. When discharging, LEDs indicate the
remaining charge (same color as charging).
Solid red:
Solid green:
Solid red:
Solid orange:
Solid green:
O:
Blinking red:
Stand-by mode
The PSU is OK
25% LED: the charge is lower than 25%
25% LED: the charge is upper or equal to 25%
50% LED: the charge is upper or equal to 50%
75% LED: the charge is upper or equal to 75%
100% LED: the charge is complete
50% LED: the charge is lower than 50%
75% LED: the charge is lower than 75%
100% LED: the charge is lower than 100%
Baery mode
Solid green:
Solid red:
O:
Blinking green:
Acve mode
The PSU is no longer working or not
connected to the mains power
The corresponding PSU is not present
Auto test mode
Buon color usage:
LED color usage:
LED color usage:
Test buon & PSU LED
OPERATION OVERVIEW
HOW DOES THE SECURE POWER UNIT WORK
Installaon steps are detailed hereaer for a rst installaon or a hot swap. Please make sure to carefully follow
instrucons.
First installaon:
Please take the usual safety measures against ESD.
All devices must be disconnected from the mains power.
When installing a new Secure Power Unit, the exisng power supply from the LiveCore™ device is moved to the Secure
Power Unit ; the second power supply is already installed in the Secure Power Unit.
Web RCS: Setup > Services > SPU
The rst step is to unplug the power supply unit from the
LiveCore™ device and to transfer it into the free slot of the
Secure Power Unit. This provide a second redundant power
supply.
The second step is to insert the head frame into the LiveCore™
device and connect the SpeakON™ connector to the Secure
Power Unit.
STEP #1 STEP #2
1 1
22
INSTALLING THE SECURE POWER UNIT
03/21/2016 - SPU001-QSG
Code: 140156
This Analog Way product has a 1 year warranty on parts and labor (except for the power supply, the frame head and
the baery that are under warranty only in case of “Dead On Arrival”). This warranty does not include faults resulng
from user negligence, special modicaons, electrical surges, abuse (drop/crush), and/or other unusual damage. In the
unlikely event of a malfuncon, please contact your local Analog Way oce for service.
Hot swap:
You may wish to replace defecve elements while the installaon is running.
To replace a defecve power supply unit while the LiveCore™ device is running, follow these steps (taking the usual
safety measures against ESD):
• Unplug the power cable from the mains,
• Unplug the power cable from the defecve Power Supply Unit and take it o,
• Fit the new Power Supply Unit,
• Plug the IEC power cable to the Power Supply Unit,
• Connect the power cable to the mains.
To replace the baery, put the LiveCore™ device in stand-by, replace the baery then turn on the LiveCore™ device.
The third step is to connect the Secure Power Unit to the
LiveCore™ through an RS232 cable. It will provide informaon
about the Secure Power Unit directly on the Web RCS
interface. Connect the ground between the Secure Power
Unit and the LiveCore™ device.
The last step is to power the Secure Power Unit. The LiveCore™
device is ready to run safely.
WARNING: In order to power the Secure Power Unit, plug IEC
cables rst in the Secure Power Unit then plug into the mains
power.
STEP #3 STEP #4
1
2
11
2
Take the usual precauons against ESD (electrostac discharge).
To ensure maximum life to the baeries used in the Secure Power Unit, some precauons of use are required.
1) In use on a Secure Power Unit:
The charging/discharging system in the Secure Power Unit automacally provides the best baery perfomance. No
acon is required.
2) Storage:
Like all baeries, when a lithium baery is not used, it is subject to a low self-discharge.
For storage periods longer than 6 months, you should monitor the level of charge and, if the baery is at 50% or less,
you must charge the baery using the "Forced charging" feature of your Secure Power Unit.
PRECAUTION OF USE AND STORAGE OF LITHIUM-ION BATTERIES
WARRANTY AND SERVICE
Autres manuels Analog way Générateur portable
