AMX Phast PLL-SD10 Manuel utilisateur

Page 1of 3 08/07/00 Rev. C

User Guide

Model PLL-SD10 Smart Dimmer

Description

The PLL-SD10 is a solid state, microprocessor-controlled

dimmer. Before the network is applied, the PLL-SD10 can control

the load with a default feature set.

If the button is pressed and released, the PLL-SD10 will

automatically ramp to its full on or off state. If the button receives

another push and release before the final state has been reached,

the PLL-SD10 will halt at that point in the load curve.

When the button is pressed and held, the PLL-SD10 will begin to

ramp slowly to its full on or off state. When released, it will halt at

that point in the load curve.

By default, the LED on the button of the PLL-SD10 is off when

the load is off, and is on when the load is on.

When the PLL-SD10 is connected to the PHASTLink network, the

following features are available for programming:

•LED Brightness and On/Off State

•Ramp Rate Adjust

•Network-Controlled Lighting Scenes

•Maximum On Level

•Push and Hold Delay

•Detachable Button (push/hold/release)

Electrical Specifications

•Max Load 600 Watts

••Supply 120 VAC, 60 Hz

•Interface PHASTLink

Junction Box Requirements

Maximum Number of Conductors

Box Dimensions (inches) Min. Cu. In.

Capacity No. 18 No. 16 No. 14 No. 12 No. 10 No. 8 No. 6

3 x 2 x 2 1/2 12.5 8765542

3 x 2 x 3 1/4 14.8 9876542

3 x 2 x 3 1/2 18.0 12 10 98763

Installation

WARNING! DANGEROUS VOLTAGE!

To reduce the risk of serious injury or death, turn all power off before installing this equipment.

WARNING!

PHAST lighting products generate heat. They should only be installed in room-temperature

(approx. 77°F, 25°C) indoor environments. Installing these products in attics, closets, or other

confined areas with inadequate ventilation or heat dissipation ability has the potential to cause

overheating and a possible fire hazard, and will void the warranty.

1. Connect the black (hot) wire to the line voltage (see Figures 2 and 3).

2. Connect the white (common) wire to neutral.

3. Connect the red wire to the load (incandescent lights, up to 600 watts).

Figure 1 -PLL-SD10

Page 2of 3 08/07/00 Rev. C

4. Connect the green wire to ground.

5. The blue wire is a low-voltage tap to connect up to seven PHAST PLL-3WAY switches (see

Figures 2 and 3).

6. Make sure the RJ-45 connectors have been correctly installed on the PHASTLink cables and

insert the RJ-45 connectors in the RJ-45 jacks on the back of the PLL-SD10 (see Figure 3).

Make sure the connectors are fully seated in the jacks.

Note: The PLL-3WAY switch also has RJ-45 jacks, but these have no connection to any

internal circuitry in the PLL-3WAY. The RJ-45 jacks on the PLL-3WAY are only

provided as a convenient means of continuing a PHASTLink line through a junction

box that contains a PLL-3WAY. Refer to the PLL-3WAY documentation for details.

7. For optimum performance, we recommend the installation of a double 120-ohm terminator in

one of the RJ-45 jacks of the last device (or the only device) in a chain of PHASTLink

devices.

To build a double 120-ohm terminator:

a. Install a 120-ohm resistor between pins 1 and 2 of an RJ-45 connector. See Figure 4 for

RJ-45 pin numbers.

b. Install a 120-ohm resistor between pins 7 and 8 of the same RJ-45 connector.

Note: Use ¼-watt or larger resistors.

8. Make sure there is a minimum 0.25-inch gap between all high-and low-voltage components.

9. Remove the plastic face plate and mount the PLL-SD10 in the junction box.

10. Screw the PLL-SD10 to the junction box through the mounting slots.

Note: For multi-gang installations, break off the metal corner tabs on the metal heat sink.

The outer tabs on the end devices may be left intact. Up to five PLL-SD10 units can

be mounted in a single multi-gang junction box without de-rating the load capacity.

CAUTION!

To avoid damaging this device and voiding the warranty:

•DO NOT connect the ground wire (green) or the 3-way control wire (blue) to the hot, load,

or neutral wires.

•DO NOT short the load wire (red) to the ground, common, or 3-way control wires.

Figure 2 -Wiring Diagram

RJ-45

PHASTLink

Neutral

Page 3of 3 08/07/00 Rev. C

Troubleshooting

Problem: LED does not come on at power-up.

1. Check the voltage across the Hot and Common wires to make sure the device is getting

power (should be 120VAC).

2. Make sure the 3-way Control wire is not shorted to Ground. If this wire is shorted, the device

may appear in Landmark Designer, but it will not operate via the button.

Problem: Dimmer works, but does not appear in Landmark Designer.

1. Check the PHASTLink cable.

2. Make sure the device's Ground wire is properly grounded and NOT shorted to Common,

Load, or Hot wires.

Technical Support

Note: There are no user-serviceable parts inside the device. Opening the device will

void your warranty and may expose you to dangerous voltages.

If you experience problems with your PHAST products, double check all external connections,

settings. If the problem persists, call your PHAST dealer or PHAST Technical Support.

•Write your PHAST dealer's number here for easy

reference:___________________________

•You can contact PHAST Technical Support at 800-979-9637 or 801-264-8090.

•Support is also available at the PHAST web site at http://phast.com

PHAST Corporation

79 West 4500 South, Building 14

Salt Lake City, Utah 84107

801-264-8090

800-979-9637

801-264-8271 FAX

http://phast.com

Figure 3 -Rear View of PLL-SD10

Figure 4 -RJ-45 Plug

(neutral)

Table des matières

Autres manuels AMX Variateur

AMX

AMX RDD-DM4/120 Manuel utilisateur

AMX

AMX Dual DC Dimmer Module RDM-2DC Manuel utilisateur

AMX

AMX Radia RE-DM6 Manuel utilisateur

AMX

AMX RDM-INC50 Manuel utilisateur

AMX

AMX RDM-INC50 Guide de démarrage rapide

AMX

AMX PRO-2400 Manuel utilisateur

AMX

AMX ALD-H48 Manuel utilisateur

AMX

AMX RDM-2INC Guide de démarrage rapide

AMX

AMX Radia RDC-DC/120 Manuel utilisateur

AMX

AMX Single Channel Lutron FDB Ballast Dimmer... Instructions de montage

AMX

AMX RDM-DC DC MODULE Instructions de montage

AMX

AMX RDM-3DC TRIPLE DC MODULE, 1,920 W (X3), 0-12... Instructions de montage

AMX

AMX RDM-2FDB DUAL FDB MODULE, 1,920 W (X2) Instructions de montage

AMX

AMX Radia Eclipse RE-DM4 Manuel utilisateur

AMX

AMX ALD-D48 Instructions d'utilisation

AMX

AMX RDM-FDB Instructions de montage

AMX

AMX RDM-DC Manuel utilisateur

AMX

AMX Incandescent Dimmer Module RDM-INC Instructions de montage

AMX

AMX RDD-DM6 6-CHANNEL INTEGRATED DIMMER MODULE Manuel utilisateur

AMX

AMX Multimode Dimmer Module RDM-MDM Instructions de montage

AMX

AMX Radia Eclipse RE-DM4 Manuel utilisateur

AMX

AMX Incandescent Dimmer Module RDM-INC50 Instructions de montage

AMX

AMX RDM-3FDB Manuel d'exploitation et d'entretien

AMX

AMX RDM-INC Instructions de montage

Manuels Variateur populaires d'autres marques

ZooZ

ZooZ ZEN54 LR Manuel utilisateur

Lex

Lex 6KW Manuel utilisateur

DIODE LED

DIODE LED TOUCHDIAL Mini Manuel utilisateur

Viessmann

Viessmann 5590 Manuel utilisateur

American DJ

American DJ DP-8A Manuel utilisateur

Teleco

Teleco TVSTICK868RGB29 Manuel utilisateur

INSTEON

INSTEON LampLinc 2457D2 Manuel utilisateur

LEGRAND

LEGRAND WattStopper RH703PTU Manuel utilisateur

ADB

ADB EURODIM TWIN TECH Manuel utilisateur

Sinope

Sinope DM2550ZB-C4 Manuel utilisateur

SkyLink

SkyLink SK7 Manuel utilisateur

Makel

Makel RC Manuel utilisateur

Lightronics

Lightronics XC-62 Manuel utilisateur

Triton Blue

Triton Blue DM-1225 Manuel utilisateur

ETC

ETC ES750 Mode d'emploi

NA OMEGA + Manuel utilisateur

GE ZB3001 Manuel utilisateur

LSC

LSC DP-1210 Manuel utilisateur